Instruction Manual XPRS2 Series XPRS102 / XPRS122 / XPRS1152S / XPRS1182S Active Loudspeaker / Active Subwoofer pioneerdj.com/support/ For other support information for this product, visit the above site.
How to read this manual Thank you for choosing this speaker. To make sure you get the most from its functions and use them effectively, please read the Instruction manual and Precautions for Use carefully. Please keep the Instruction manual and Precautions for Use together with the Warranty.
Rear panel (subwoofer model) DSP control With the integrated DSP control menu, you can choose from multiple DSP and system settings on the speaker. To access the DSP control menu, follow the steps below. 1. Press the MASTER VOL knob and the DSP control menu will appear. 7 6 5 a 8 4 3 9 2. Use the MASTER VOL knob to scroll through the menu items. 3. Press the MASTER VOL knob to select the menu item you want to modify. The menu item you chose will open on the right side of the DSP menu. 4.
MENU You can use the Input Settings menu to configure the speaker’s input sensitivity control as well as the Delay and Phase control settings. HI MD LM LO 12.1K 2.52K 500.0 101.5 Back Default: 0 decibels Range: -18 decibels – +18 decibels ALLBYPASS will be deleted, invalidating all set EQs. FLAT is to restore all adjusted EQs to factory settings. NOTE The indoor equalizer (EQ) range shown is the factory default range for individual speakers.
2. Select Yes. Pole socket Front 35-mm-diameter pole socket 3. When the prompt asks if you’re sure, select Yes. Pole socket Installation using a speaker pole XPRS102, XPRS122 The speaker will reboot the system and reset to the original factory settings. Installation and connections XPRS1152S, XPRS1182S Important notes on installation The sound produced by the speaker is subtly influenced by the conditions of the room you use it in.
Active subwoofer and active satellite speaker Connections For active full-range speaker system CAUTION Make your initial connections with all the equipment powered off and ensure all the main volume controls are turned down completely. 1. Connect one end of a signal cable to the Output Left/Right on your mixer (with a stereo jack or XLR connector) and connect the other end of the cable to the Line Input (COMBO) on your active speaker (with a stereo jack or XLR connector). 2.
DIGITAL SIGNAL PROCESSING MASTER VOL DSP DISPLAY SIG SIG MIC HI-Z 1 2 OFF MAX SIG SIG/LIMITER POWER OFF MAX 3 OFF MAX INPUT STEREO MIC/LINE HI-Z/LINE MIX OUT Vocal Microphone DJ Mixer, Etc. Instrument The direction of the arrow indicates the signal path.
Specifications Model System type Transducer low Transducer driver Frequency response (-6 dB) Max SPL Power rating 4 DSP modes Electronic protections XPRS102 Multi-purpose, 2-way active loudspeaker with DSP controls 10” woofer, 2.5” voice coil 1” exit compression driver, 1.75” voice coil 50 Hz – 20 kHz 129 dB Class D 2000 W (peak) LIVE / MUSIC / SPEECH / MONITOR Thermal / overload / digital Limiter / compressor Connectors Input: MIC / LINE (Combo) / HI-Z / LINE (Combo) / 3.
© 2022 AlphaTheta Corporation. All rights reserved. 6F, Yokohama i-Mark Place, 4-4-5 Minatomirai, Nishi-ku, Yokohama, Kanagawa 220-0012 JAPAN 〒220-0012 神奈川県横浜市西区みなとみらい4丁目4番5号 横浜アイマークプレイス6階 6F, Йокогама i-Mark Place, 4-4-5 Минатомирай, Ниси-ку, Йокогама, Канагава 220-0012 ЯПОНИЯ Artemis Building, Odyssey Business Park, West End Road, South Ruislip, Middlesex, HA4 6QE, U.K. TEL: +44-203-7617-220 2050 W. 190th Street, Suite 109, Torrance, CA 90504, U.S.A.
