Operation Manual

11
Before You Start
Operating range of remote control unit
The area in which you can use the remote control to operate the
VSX-D709S is fairly large. To use, point the remote control toward
the remote sensor on the front panel of this unit while within the
range shown right.
Remote control may not function properly if:
• There are obstacles between the remote control and the remote
sensor.
• Direct sunlight or fluorescent light is shining onto the remote
sensor.
• The receiver located near a device emitting infrared rays.
• Operated simultaneously with another remote control which
uses infrared rays.
Installing the Receiver
Please note:
• Do not place objects directly on top of this unit. This would
prevent proper heat dispersal.
• When installing in a rack, shelf, etc., be sure to leave more than
8 inches of space above the receiver.
Opening the Front Panel
To open the front panel push gently on the lower third of the panel with your
finger.
Î

SOURCE
ENTER
LOUDNESS
INPUT ATT
DIGITAL NR
FL DIMMER
REMOTE SETUP
SYSTEM SETUP
SIGNAL SELECT
TV VO
L
TV
TVFUNK
ENTER
TUNE
TUNE
D.ACCESS
BAND
GUIDE
M
ENU
CLASS
RETURN
MIDNIGHT DSP STEREO
FU
N
C
T
IO
N
ADVANCED
STANDARDMUTE
S.M
ODE
CLEAR
DTV INFO
AV PRE-PRO
GRAM
M
ED AND LEARNING
REMO
TE CONTROL UNIT
/ DSP
R
ECEIV
ER
D
IR
ECT CO
N
TRO
L
M
PX
DTV ON / O
FF
DTV M
ENU
ST ST
CHANNEL
EFFECT/CH SEL
RECEIVER
TV CONTROL
MASTER VOLUM
E
DISC
+10
VIDEO SELECT
M
ULTI CONTRO
L
MULTI CH INPUT
DVD
CD
CD-R
TUN
TVC
RECEIVER
1 2 3
4 5 6
7 8 9
 ! ⁄
0
*‹&
2
TV
VCR
1
VCR
2
4 ¢
¶
30
30
23 feet (7m)
8 inches (20 cm )
Receiver
PREPARATION
Remote Control
Receiver
To CONTROL IN
terminal of another
PIONEER component
bearing the Î mark.
PIONEER
component bearing
the Î mark.
• You can also control PIONEER components (and those made by other manufacturers) by pointing the
receiver's remote control directly at the respective component. This type of operation does not re-
quire control cords. All you have to do is recall the appropriate the stored settings (see p.55-56).
• If you use a remote control hooked up via the CONTROL IN jack with a control cord, you won't be able
to use this unit's remote control.
memo
The PIONEER SR System: Operating other PIONEER components
Connecting an optional control cord allows you to operate other PIONEER components simply by pointing the
receiver's remote control at the remote sensor on the front panel of the receiver. The receiver then sends the
remote control signals to the other devices via the CONTROL OUT terminal.
OUT
IN
CONTROL
Î
SOURCE
ENTER
LOUDNESS
INPUT ATT DIGITAL NR FL DIMMER
REMOTE SETUP SYSTEM SETUPSIGNAL SELECT
TV VOL
TV
TVFUNK
ENTER
TUNE
TUNE
D.ACCESS BAND
GUIDE MENU
CLASS
RETURN
MIDNIGHT DSP STEREO FUNCTION
ADVANCEDSTANDARD MUTE
S.MODE CLEAR DTV INFO
AV PRE-PROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
/ DSP
RECEIVER DIRECT CONTROL
MPX DTV ON / OFF DTV MENU
ST ST
CHANNEL
EFFECT/CH SEL
RECEIVER
TV CONTROL
MASTER VOLUME
DISC
+10
VIDEO SELECT
MULTI CONTROL
MULTI CH INPUT
DVD
CD CD-R TUN TVC
RECEIVER
1 2 3
4 5 6
7 8 9
 ! ⁄
0
*‹&
2
TV
VCR
1
VCR
2
4 ¢
¶