Manual

ManualsBrandsPioneer ManualsAudio EquipmentOfficial Pioneer receiver

OPERATING USING GUI

ZS I _ Intelligent

Ikj System Control

GUI

GUI (Graphic User Interface) lets you use the TV screen to

operate the system.

• Press the GUI MODE button on this unit or the G.U.I. button

on the remote control, and operation indications for the

currently selected function are displayed on the TV screen.

• To operate, use the z_,_>,v,<3buttons on the remote control

(they light up when the GUI mode is ON) or the MULTI-

JOG on this unit to move the cursor (the hand shaped mark)

displayed on the TV screen. When the cursor is on the

button you want to operate, press the GUI ENTER button.

• When the operating instructions say "Press the button",

this means move the cursor to the desired button and press

the GUI ENTER button.

NOTE:

• If you do not perform any of the operations above within 10 N 30

seconds, the GUIdisplay is canceled.

• <Multi-voltage model only>

Set the rear panel PAL/NTSC switch to match your TV's color

system. Thescreen will be unclear if the color system does not

match.

RECEIVER CONTROL BUTTONS I

• The buttons in the following explanation are the receiver operation button indications common to all function displays. (The

illustration shows LD operation indications.)

(Figure 1" Main Menu display) (Figure 2: Sub Menu display)

® ®®

1_ SURR MODE (Surround Mode):

Switches between the five DSP modes and the DOLBY PRO-

LOGIC mode as follows.

DOLBY PRO-LOGIC _ JAZZ _ DANCE q

SURROUND

ff_ PRO-LOGIC _ HALL _ SIM. SURR ÷

THEATER (SIMULATED SURROUND)

The selected mode is displayed on the right of the function

indications.

3CH LOGIC:

Switches DOLBY 3CH LOGIC ON/OFF.

When ON, "3CH LOGIC" is displayed on the right of the

function indications.

® SUPER BASS:

Swithces SUPER BASS ON/OFF.

When ON, "SUPER BASS" is displayed on the right of the

function indications.

4_ DIRECT:

Press this to listen to source sound without passing the audio

signal through sound quality and balance adjusting circuitry.

The surround mode, and rear and center speakers are

automatically switched off.

COPY:

Press to copy from a Laserdisc to a VCR, or to copy between

VCR 1 and VCR 2.

When you press this button, the display changes to COPY

indications. (This button is displayed only when the function

is LD, VCR 1 or VCR 2. Refer to page 32)

(_ SURR EDIT (Surround Edit):

Press to make adjustments such as level setting for the

currently selected surround mode or DOLB¥ 3CH LOGIC.

When you press this button, the display changes to

SURROUND EDIT indications. (Refer to page 33)

NOTE:

You cannotpress this button when the surround mode is OFF.

SET UP:

Press this button and the display changes to the SET UP

MENU. (Refer to pages 34~36)

Display change button:

Switches between Main Menu display (Figure 1) and Sub

Menu display (Figure 2).

® V.SEL (VIDEO SIGNAL SELECTOR):

This switches only the video signal in sequence, leaving the

sound unchanged. (Refer to page 32.)

I--* VCR 1----_VCR 2 --_ VIDEO ---_ TV/SAT--'* LD --I

off •

SLEEP

This operates the sleep timer. Move the cursor to this button,

and each time you press the GUI ENTER button, timer

settings change as follows.

[_ 90min---_60min----*30min-_*0min (off)--I

@ SYSTEM OFF

Switches power to this unit, the TV, and the currently selected

function OFF.

NOTE:

When you press the SYSTEMOFFbutton, power to components

not made by Pioneer switches ON if power to these components

was alreadyswitched OFF.