IMPORTANT Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference. NOTICE The serial number for this equipment is located on the rear panel. Please write this seriai number on your enclosed warranty card end keep it in • secure area. This is for your security.
IMPORTANT READ INSTRUCTIONS -- AN the safety and operating instructions should be read before the p_oduct is _perated RETAIN INSTRUCTIONS -- The safety and operating it_structions should be retained for future reference HEIEO WARNINGS -- Art war ni_gs o_ the product and in the operating instrubeons should be adhered to =OLLOW INSTRUCTIONS -- All operating and use instructions should be followed *_LEANING -- Unplug this product from the wall ooPet before cleanir)g The product should be cleaned only wit h a p
DTS (Digital Theater Systems) decoder equipped _ (VSX-D608 only) DTS is the digital sound system introduced m theaters Playback of DVD, LD, and CD recorded creates the enwronment of a theater or the sensahon of a concert hall in your home "DTS" and "OTS Drgltal Surround" are trademarks Manufactured m DTS audio of D_glta/ Theater Systems, Jnc under hcence from Digital Theater Systems, Inc.
Introductory Information ............................................................ 6 Checking the Supphed Accessories .................................. How to Use Th_s Manual ............................................ 6 6 Preparing the Remote Control ................................ Receiver InstaHabon ............................... 6 7 When Making Cable Connections ............................. 7 Connections .................................................................................
[ Checking the Supplied Accessories ] Please check that you have recewed all of the fol)owing accessories w=th the receiver Lil c FM wire antenna AM loop antenna Remote control unit "AA" IEC LR6 batteries x 2 I How to Use This Manual Th=s manual is divided into two main sections SET UP This section explains how to make the necessary connections from the receiver to your other audio and wdeo components.
Operating range of remote control unit Point the remote control toward the remote sensor [] on the front panel of this umt to operate The remote control umt will operate the receiver for up to a distance of 7 meters (23 feet) w_thrn 30* angle on each s_de of the sensor of the remote sensor as dlustrated below 7m(23 Operating other PIONEER components Connecting an optional control cord allows you to operate other PIONEER components simp)y by pmntmg the receiver'S remote control at the remote sensor on
] I Antennas FM wire antenna Connect the FM wire antenna and fully extend (for best reception, attach horizontally along a window frame, etc.). AM loop antenna f: n this section, the area within dotted line only applies to the (See below) SX-D608 VSX-D608 r • AM loop antenna _, Assemble the antenna ,_ Twist exposed wire strands together and insert into AM antenna terminals ,3, Attach to a wall, etc (if des=red) and face toward the direction prov=ding the best recept=on.
I Audio Components Connections I Be sure to switch power to standby and remove the power cord from the wall outlet when you make or change connections. Connect your audto components as shown below Refer to "Digttal Connecttons" on page 11 when making digital connect=ons from your DVD or LD player.
[Video Components Connections • When connecting components, the receiver should be off and the power cord unpluged. • Connect your video components as shown below. Also, refer to "Digital Connections" on page 11 when making digital connections from your DVD or LD player. • Although only "$2" is printed on the S-Video jacks on the rear panel, S, $1 and $2 S-video connection can be made as well NSX-D608 U.S. model only).
[ Digital Connections ] Digital components can be connected as shown below. You can select up to four (three on the VSX-D508) of the following be assigned to the digital inputs on this unit: DVD/LD, TV/SAT, MD/TAPE, CD, VCR1 (VCR). To assign the digital inputs, refer to "Setting Up for Surround Sound" on page 16) The digital signal input is output directly to digital recording components from the optical digital output jack.
I DVD 5.1 Channel Connection 1 DVD and LD discs are often compatible with both 2 channel and 5.1 channel audio output formats, Refer to page 33 for more information on how to switch between the two input methods. Connections can be made from a DVD player, Dolby Digital decoder, or DTS decoder equipped with 5.1 analog outputs to the 5.1 analog inputs on this unit, VSX-D608 ! t with 5.1 channelanalogue I Components equipped I o.__putjacks -- [ The 5.
I Speakers I • Use speakers with a nominal impedance of 6 _ to 16 _. • The front speaker R terminal is only used in stereo mode (Not available during DVD 5.1 channel, DSP mode, 1313 (Dolby) mode (VSX-D508), or []/DTS mode (VSX-D608)). • When you use the speaker on your TV as a center speaker, please connect the CENTER PREOUT jack on this unit to the audio input jack on your TV. In this case, the center speaker shown below is unnecessary.
Connecting To use separate additional amplifiers amplifiers to power your center speaker, make the connections shown below. Do not make simultaneous connections to both the CENTER PREOUT jack and the CENTER SPEAKER terminals. (e.g. Do not connect a separate power amplifier to the CENTER PREOUT jack if you have already connected a center speaker to the CENTER SPEAKER terminal.
Speaker placement To achieve the best possible surround sound, install your speakers as shown below securely to prevent accidents and improve sound quality Be sure all speakers are installed Sub Woofer F,'° ttCeote, / Position • Install the left and right front speakers at equal dtstances from the TV • When mstalhng speakers near the TV, we recommend using magnet=cally shielded speakers to prevent possible interference such as distortion in the color of the TV screen If you do not have magnetically s
I Setting Up for Surround Sound ! Be sure to switch the power of this unit on {The STANDBY indicator goes out) before operating. To ensure the best possible surround sound, be sure to complete the following set up operations. This is particularly important when using the IX] (Dolby) sound mode, You only need to make these settings once (unless you change the placement of your current speaker system or add new speakers, etc.).
SPEAKER setting mode Establishes the size and configuration of the speaker system you have connected. In the display, "F", "C", and "S" refer to front, center, and surround speakers respectively. Speaker size is denoted as "L" for large speakers, "S" for small speakers, and "8" (asterisk) if no speaker is connected. If the cone size of your Ez .3 -B ,._ T speaker is larger 1 12 cm (5 in.), please set to Large. Press _ or _' to set the front speaker.
SUB WOOFER 0NIOFF setting mode Sets whether the SUB WOOFER is used or not. • • Initial setting is "ON", Setting the front speaker in the "ON" position, _" _:, LI _ I{[.., Cr_Sb_er size to "Small" in the SPEAKER setting mode automatically Press z_ or _ to select sub woofer Q l',J frequency sett,ng locks the sub woofer ON or OFF. mode Setting speakers to "Small" in "SPEAKER setting mode" sends the respective channels' bass frequencies to the sub woofer lot "Large" speakers).
Low cut filter ON/OFF Turn the low cut filter ON when setting mode distorted sound is output through the sub woofer. • Initial setting is "OFF". • If the SUB WOOFER is set to "OFF" in the SUB WOOFER ON/OFF setting mode, the low cut filter cannot be set. • The low cut filter is not effective when DTS signals are input. L.L."," FRONT u"_, .... ,, -s ,° speaker Press _ or v to select low cut filter ON or OFF.
Dynamic range control setting mode Dynamic range is the difference between the loudest and softest sounds in any given signal. The dynamic range control helps you play back sounds so the quieter sounds are audible yet the louder sounds don't get distored. It does this by compressing the dvnamic range, When watching s movie at low volume, setting this function enables low level sounds to be heard more easily.
Optical digital input 3 setting Sets the input component to be assigned (VSX-D608 to the optical only) input 3 jack, • Initial setting is "TV'. • You cannot assign the same component to more than one digital input jack. The jack most recently selected is established for the component and the jack formerly selected is turned off. • DVD/LD, TV/SAT, CD, MD/TAPE, VCR 1 (VCR only on VSX-D508) digital input connection is possible.
Setting Up the Remote Control 1 In addition to controlling the receiver, the supplied remote control can operate your other components (DVD, MD, VCR, TV, LD, CD, etc.). If your component(s) are listed in the "Preset Code List" on page 56, simply recall the corresponding preset code. Recalling preset codes The following steps show you how to recall preset codes for each MULTI CONTROL button.
3 Press A or V repeatedly to display the name of the component's manufacturer. ("VCR" is displayed on VSX-D508) ! _ . At J J - F_U_; F_ A list of all available preset codes is provided 4 Point enter the remote the 3 digit toward the setup code. $ ILr_ -8=. on page 56. component to be controlled, When you enter the setup code, the remote emits a power ON/OFF signal. If the component turns ON or OFF, you have entered the proper code.
I Display 1 3 r_. :_ _'_ ,_ (_, _ _ ! I_IJ ,LI_! VSX-D6O8 only SIGNAL _ _5_ SELECT indicators _) Digital indicators dts (VSX-D6O8 only) : Lights when DTS signals are input. (DoIby/DTS mode is ON) 0_PRO LOGIC : When the Dolby mode on the receiver is on, this indicator lights during 2 channel playback of Dolby Digital sources. r]0DIGITAL : When the Dolby mode on the receiver is on, this indicator lights to indicate playback of a Dolby Digital signal.
I Remote I Control These pages describe the buttons on the remote control used to operate the receiver. @ RECEIVER button Press to switch the receiver on or to put in standby. MUTING button Press to mute the volume. "MUTING" display. Press again to cancel. z_/_F/<_/D/ENTER ® appears in the _7_ Number buttons These buttons can perform a variety of different functions depending on the remote operation mode.
[ Front Panel 1 VSX-D608 I . "_E PR, l s_uoul O STANDBY/ON button LOUDNESS button Switches the loudness on or off, Use to raise the level of the low and high frequencies so they can be more easily heard when listening at low volumes. Press to switch the receiver on or put in standby. STANDBY indicator Lights when the receiver is in standby mode, (Please note that this receiver consumes a small amount of power (2.
VSX-Dh08 I SIGNAL SELECT button Use to select input signals for the digital components. First press DVD/LD, TV/SAT, MD/TAPE 1, CD or VCR 1 (VCR on VSX-Dh08) (_, Function buttons) to select the component, then press SIGNAL SELECT repeatedly to select one of the following: ANALOG : Selects the analog (R and L) audio signals. DIGITAL : Selects the digital audio signals. This receiver automatically detects and displays the format of the signal being input.
This receiver incorporates Surround two surround modes for enjoyment of a variety of program sources. modes (3_ (Dolby) mode Use this mode when playing Dotby Digital or Dolby Pro Logic software. the input signal, so all you have to do is enjoy! Decod(ng switches automatically according to You can identify Dolby Digital software by the _or ,,_._ marks. Most Dolby Pro Logic software is marked [3B_, but unmarked software may also incorporate Dolby Pro Logic.
Switching ANALOG/DIGITAL Signal Input The input of the component set in the digital input setting (Refer to page 20, 21) can be switched to an analog or digital input signal by pressing the SIGNAL SELECT button. 1 Press SIG. SELECT on the remote control or SIGNAL SELECT on the front panel to select the input signal corresponding to the source component, Each press switches between ANALOG and DIGITAL signal selection. - SIG.
Playing Sources with Dolby Digital 1 or DTS Sound Follow steps 1 to 3 of the playback "Playback" on page 40.) procedure, (Refer to _i' Turn on the power of the playback component• 21 Press RECEIVER to turn on the receiver. 5 r3" Press FUNCTION to select the source component 2 3 2 Press SIG.SELECT on the remote control or SIGNAL SELECT on the front panel to select DIGITAL. (Refer to "Switching page.) 3 you want to play. ANALOG/DIGITAL Press DO to switch the i3D/DTS D508) mode on.
Selecting a Sound Mode 1 To ensure the best possible surround sound, be sure Surround Sound" (starting on page 16) before using (Dolby) sound mode. When using the sound modes, mode is turned on, selection automatically switches Surrround to complete the set up procedures described in "Setting Up for the sound modes. This is particularly important when using the 130 SPEAKERS A are used. if SPEAKERS B are selected and a sound to SPEAKERS A only. operation 1 Press RECEIVER.
Switching the Dolby/DTS mode (ADVANCED THEATER mode)(VSX-D608 only) Switch the Dolby/DTS mode by pressing the DO button. When Dolby/DTS mode is ON, Dolby Pro Logic, Dolby Digital, and DTS signal processing is performed automatically corresponding to the input signal. Switch the Dolby/DTS mode on and off by pressing the remote control or 00/DTS on the front panel. Each presschangesthe display as follows.
DVD 5.1ch input playback Connect a component with 5.1 channel output to enjoy the surround Press DVD/LD DVD/LD (VSX-D608) on the unit. Each press switches --L_ the input: DVD/LD _ DVD/LD 5.1ch ooo _) ._r_ <, c==n sound created by 5.1 channel playback. 'i '_: i _ _ -B i,. l_ l, 1j : l I c: h _1 DVD/LD (VSX-D508} • When DVD 5.1ch input is selected, Dolby mode, DSP mode, SIGNAL SELECT, input ATT, DIRECT, TONE, MIDNIGHT mode, DIGITAL NR and speakers B cannot be operated. • When DVD 5.
Reducing noise during playback When DIGITAL NR is on, auditory (DIGITAL NR function) noise during DIGITAL NR (VSX-D608 only) playback can be reduced, Press DIGITAL NR on the front panel, Each press switchesDIGITAL NR on or off, 13 f / / 33 I \ / f ]] .Ltl/ J.t / L. _LI • In cases described -8_,n below, DIGITAL NR cannot be used. []/DTS mode is ON. DSP mode is ON. DVD 5.
Listening in MIDNIGHT Listening Mode 1 When the volume is low, surround effects tend to become less than satisfactory. Turn the MIDNIGHT listening mode on to enjoy the effects of quality surround sound even at low volumes. This mode allows you to hear effective surround sound of movies at low volume levels. Press MIDNIGHT. Each press switches MIDNIGHT listening mode on or off. I_ 1" _rs L _ - rl I_lf T L ['1 The effect is automatically J T -BI,. adjusted according to the volume level.
Automatic and Manual Tuning The following steps show you how to tune (n FM and AM radio broadcasts us(rig the automatic (search) and manual (step) tuning functions, if you already know the exact frequency of the station you want, see "Direct Tuning" on the following page. 1 3 2 Press FUNCTION repeatedly on the remote or FM/AM on the front panel to select the tuner, Press TUNER to set the remote to the tuner operation mode. The station you were previously ;io 4 1 tuned to is received automatically.
[ Direct Tuning The following steps show you how to tune directly to a specific frequency using the remote control 1 Press FUNCTION repeatedly on the remote or FM/AM on the front panel to select the tuner. Press TUNER to set the remote to the tuner operation mode. The station you were previously tuned to is received automatically. 2 2 Press ENTER to select the band (FM or AM).
[ Memorizing Frequently ! Tuned Stations The following steps show you how to memorize up to 30 radio stations in 3 classes (each holding memorizing FM frequencies, the receiver also memorizes the MPX mode (STEREO or MONO). Using the front 32 10 channels). When panel 1 Tune in the desired station. See "Automatic and Manual Tuning"or "Direct Tuning"on pages36, 37. 2 Press MEMORY to activate the memory function. "A--" blinks in the display, _j i-_ i-- f-3 .
Recalling Using the Memorized the remote Stations 1 control 1 Press FUNCTION repeatedly on the remote or FM/AM on the front panel to select the tuner. Press TUNER to set the remote to the tuner operation mode. The station you were 3_3 "] _LI 2 1 3 2 tuned I-3 :3 _3 .3 I"" -3 I'lLJ -_ to is received automatically. 'dB Press CLASS repeatedly to select a class.
Playback 1 1 2 2 Turn on the power of the playback component. ___J Press RECEIVER to turn on the receiver. Be sure that the standby indicator turns off on STANDBY indicator the front panel. 5 3 Press FUNCTION I . ( I L ._-_ _ to select the source you want to playback.
Adjusting bass and treble (tone control) Use BASS (+/-) or TREBLE (+/-) to adjust the low and high frequencies. TREBLE +/- Press BASS (+/-) to adjust the low frequencies, | Press TREBLE (+/-) to adjust the high frequencies. BASS +/T i-_l _- rt [- 3.3 jj -- -_ _;i • The tone control can be adjusted in a range of _+6. • Pressing + and - simultaneously restores the setting to O. • In cases described below, the tone control cannot be adjusted.
I Recording from Audio Components l The following operations show you how to record audio to the cassette, DAT, or MD deck connected or TAPE 2 MONITOR jacks. The receiver's volume, balance, tone (BASS, TREBLE, and LOUDNESS), and surround on the recorded signal. 1 2 to the MD/TAPE 1 effects have no effect Select the component you want to record. Press SIG.
I Recording from Video Components I The following operations show you how to record audio and video to the video tape recorder connected to the VCR 1 or VCR 2 (VCR only on VSX-D5O8) jacks. -_ he receiver's volume, balance, tone (BASS, TREBLE, and LOUDNESS), and surround on the recorded signal. 1 Select the component you want effects have no effect to record. Be sure to press SIG. SELECT on the remote or SIGNAL SELECT on the front panel to choose "ANALOG".
Remote Controlling Other Components DVD or LD player operations (_ Before to perform operations, remote attempting to the DVD/LD operationthese mode. press the DVD/LD (MULTI CONTROL) button to switch the Number buttons Use to select chapters (tracks). 4-9/ _1< : Hold down for fast reverse playback. : Hold down for fast forward playback. _1< : Press to return to the beginning of the current chapter (track). Press repeatedly to return to the beginning of previous chapters (tracks).
TV operations Before attempting to perform these operations, the remote to the TV operation mode. press TV CONTROL or TV/SAT (MULTI CONTROL) to switch Press to switch the TV on or off. Raises the volume of the TV. Lowers the volume of the TV. _4_Number ® buttons Use to select a specific TV channel. TV Press to switch the TV on or off. (This operation is possible regardless of the current remote operation mode, however, it can only be used with the component assigned to TV CONTROL.
SAT (Satellite Tuner) operations - The operations are available from the receiver's remote22). control presetfollowing code (refer to "Setting up the Remote Control" on page after you • CONTROL) Before remote attempting to perform these operations, to the TV/SAT operation mode. press the TV/SAT (MULTi recal_ a Satellite button tuner to switch the Press to switch the satellite tuner on or off. Use as cursor buttons to obtain information programs.
CD player operations Before attempting perform these operations, to the CD operation to mode. press the CD (MULTI CONTROL) button to switch the remote Press to switch the CD player on or off. 1 Gnu Press to pause playback. _3 Press to start playback. Press to stop playback. ® Number buttons Use to select tracks. ® : Hold down for fast reverse playback. IH_ : Hold down for fast forward playback. _<-<: Press to return to the beginning of the current track.
MD recorder operations Before to perform thesemode. operations, remote attempting to the MD/TAPE operation press the MD/TAPE (MULTI CONTROL) button to switch the Press to switch the MD recorder on or off. Press to pause playback. Press to start playback. Press to stop playback. Number buttons Use to select tracks. <_1 : Hold down for fast reverse playback. I_ : Hold down for fast forward playback. I<< : Press to return to the beginning of the current track.
Cassette deck operations [_ Before attempting to perform these operations, remote to the MD/TAPE operation mode. press the MDFFAPE (MULTI CONTROL) button to switch the Press to switch the cassette deck on or off (not possible with all models). Press to pause playback or recording. Press to start playback. ®.. Press to stop playback or recording. -<-< : Press to rewind the tape. Hold down during playback for fast reverse playback (not possible with all models). : Press to fast forward the tape.
VCR operations Before attempting to perform operations, press the VCR 1 or VCR 2 (MULTI CONTROL) button to switch the remote to the VCR operationthese mode. o Press to switch the VCR 1 or VCR 2 (VCR only on VSXD508S) on or off (not possible with all models). II Press to pause playback or recording. ® Press to start playback. Press to stop playback or recording. Number buttons Use to select a specific channel on the VCR's TV tuner.
[ Background Control of Other Components The following steps show you how to control one component to rewind a tape while listening to CD, etc. 1 ] while listening to another. This may be useful if you want Select a component, For example: then start playback. Press FUNCTION to select the CD player, then press the CD button, and start playing a CD. (You should hear the sound of the CD playing back.) 2 Press MODE CHECK to display the current operation mode.
Dolby Digital 1 Dolby Digital is a compression format which records the sound of 6 channels of the theater surround system (Dolby Digital) on the movie film digital track. Of the 6 channels, the sub woofer channel is intended for bass only, and because the frequency range is smaller than the main channel, it is expressed as 5.1 channel. Dolby Digital is the name of the Dolby surround multi-channel Surround System and Do,by Pro Logic Surround System.
DTS DTS has been adopted as a sound recording format for latest movie theaters since the release of "JURASIC PARK" in 1993, and has a good reputations for high quality sound and dynamic surround effects. In this system, 6 channels of digital sound are recorded on CD-ROM, not on the film. It adopts a simultaneous playback format. With a low rate of compression of sound signals and a high rate of transmittance, higher sound quality format is produced.
Troubleshooting 1 Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service center or your dealer to carry out repair work. Symptom The power does not turn ON.
Symptom Cause Remedy Broadcast stations cannot be selected automatically, Weak radio signals. Connect an outdoor to page 8). No sound from surround speakers. Speaker settings are incorrect. Refer to "SPEAKER setting mode" on page 17 to check the speaker settings. Refer to "Setting the volume level of each channel" on page 21 to check the speaker levels. Connect the speakers (refer to page 13). or center The rear and/or center levels are turned down.
I Preset Code List Device Manufacturer DVD TOSHIBA SONY PANASONIC JVC SAMSUNG SHARP AKAI RCA PIONEER SONY PANASONIC KENWOOD PHILIPS MITSUBISHI RCA PIONEER LD SAT VCR RCA SONY PIONEER RCA ZENITH MAGNAVOX FISHER PANASONIC TOSHIBA JVC HITACHI SONY MITSUBISHI TAPE SANYO SHARP GOLDSTAR OPTIMUS GRANDIENTE PIONEER SONY TECHNICS KENWOOD TEAC DENON ONKYO YAMAHA JVC FISHER I Code 001 002 003 004 005 006 007 009 O00, 003 101 105,106 103 104 100 107 100 102 (DVD code) 201,203 202 200 401,406,408,414,405,413,
Specifications Amplifier FM Tuner Section Section Continuous average power output of 100 watts* per channel, min., at 8 ohms, from 20 Hz to 20,000 Hz with no more than 0.09 %** total harmonic distortion (front). Continuous Power Output Front .................................. 100 W + 100 W (1 kHz, 0.8 %, 8 _l) Center ............................................... 100 W (1 kHz, 0.8 %, 8 _) Rear ................................... 100 W + 100 W (1 kHz, 0.
We Want You Listening I J_FI'_N] N(; For A Lifetime U sod wisely, y (mr new sonnd equipmem 'a'i_l pro'dale a liletirne of fun and enjoynlcnt. Since head ng damage from loud noise is often undetectablc until it is too [ate. this manufacturer and the Electronic Industries Association's Consunler t]eclronics ¸Group recommend you avoid prolonged cxposuTe 1o exccssi'_c n_/ise Tbix list of sound le,.,clsis included I()l¸ your protecbon.
Published by Copyright All PIONEER ELECTRONIC CORPORATION _ _,M_,o _c.om_, M_o AUSTRALIA DE MEXICO © P_oneer 1998 Electronic Pioneer Corporation Etectronic Corp,)rat=on reserved¸ k_,Tokyo1_3.B69_. JaO_ PIONEER ELECTRONICS [USA] INC. PO. BOX 1540, Long Beach, California 90901 1540 PIONEER ELECTRONICS OF CANADA, INC. 300 Allstate Parkway, Markham, Ontario L3R OP2, Canada PIONEER ELECTRONIC [EUROPE] N.V. Haven 1097, Keetberglaan 1, 9120 Melsele, Belgium TEL: 03/570.