Quick Start Guide

CYR1298-A < 5 > CYR1298-A < 6 > CYR1298-A < 7 > CYR1298-A < 8 >
Dedicated App
The dedicated app “Dash Camera Interface” can be used to check the video recorded on this product or make settings
on the screen of an iPhone or Android device.
To use this app, a Wi-Fi connection must be made between this product and iPhone or Android device beforehand.
1 Set the Wi-Fi function of this product to on.
2 Operate the device to select this product as the Wi-Fi connection device.
The SSID name (access point name) and password of this product can be checked in the Wi-Fi settings screen.
• Only one device can be connected to this product at any one time. When a second device is connected, the first
device is disconnected.
• While a Wi-Fi connection is made, no operations can be performed on this product. If a function button is pressed
while a Wi-Fi connection is made, a message will be displayed prompting you to break the Wi-Fi connection. If you
select [Yes], the Wi-Fi connection will be disconnected, and operations on this product will be enabled.
• You can change the SSID name of this product by operating the dedicated app “Dash Camera Interface”. Note,
however, when the SD card is formatted, the SSID name returns to its default setting.
• It is recommended to enter the search term “Dash Camera Interface” in the search field to search for the application.
Dash Camera Interface
Check the Accessories
Main Unit×1 2nd Camera×1 Mounting Bracket×1 Power Cable
(5 m/16 ft. 5 in.)×1
Mini Pin Jack-RCA
Conversion Cable
(0.2 m/7-7/8 in.)×1
AV Cable
(5 m/16 ft. 5 in.)×1
2nd Camera
Connection Cable
(3 m/9 ft. 10 in.)×1*
2nd Camera
Connection Cable
(6 m/19 ft. 8 in.)×1*
microSDHC Card
(16 GB)×1
Quick Start Guide×1 Warranty×1 Cleaning Cloth×1
* The 2nd camera connection cable is included already connected.
During playback
56 78
5 Back
6 Next file
7 Previous file
8 Play/stop, delete
During MENU screen display
9a bc
9 Back
a Up*
Hold down to switch Wi-Fi on/off
b Down*
Hold down to switch microphone on/off
c Confirm
* When the volume or sensitivity MENU screen is displayed, increase or decrease the volume or sensitivity.
Inserting and Ejecting the microSD Card
Turn off the power to this product when inserting and removing the microSD card.
Inserting the microSD Card
Hold the top edge of the microSD card, position the
microSD card so that the label is facing the backside of
this product, and slowly insert it into the microSD card slot
until it clicks.
CAUTION
Do not insert the microSD card at an angle. Doing so
may cause damage.
Ejecting the microSD Card
Slowly push in the top edge of the microSD card until
it clicks (1). The lock will be released. Pull out the
microSD card (2).
Part Names
b
9
4
a
d
3
5
1
6
2
c
87
e
f
Top
Front
Left side
Right side
Back 2nd camera
1 AV Output Terminal
2 Power Port
Connect the power cable and AV cable.
3 2nd Camera Connection Terminal
Connect to the 2nd camera connection terminal
(e) using the 2nd camera connection cable.
4 microSD Card Slot
5 System Indicator
6 LCD
7 Function Buttons
8 Lens
Pioneer polarized filter AD-PLF100 (sold
separately) can help reduce reflections of the
dashboard onto the windshield, and enable the
capture of high-contrast videos.
9 Speaker
a Microphone
b Reset Button
Press this button with the tip of a ballpoint pen to
reset this product.
c Angle Adjustment Jog Dial
The angle of the lens can be adjusted by turning
this dial.
d Mounting Bracket
e Connection Terminal
f Lens
Status Display
The status display shows the operating status of this product.
00:00
12 3 54 6 7 8
1 Recording in progress
2 Elapsed recording time
3 Event recording status*1
4 Parking mode
5 Sound recording*2
6 Wi-Fi connection status*3
7 GPS reception status*4
8 Power status
(
: Battery mode  : Charging)
*1 When manual event recording is performed or vibration is detected in the event recording mode, and event
recording has been activated, “×2” is displayed.
*2 A red “\” is displayed when sound recording is set to off.
*3 During a Wi-Fi connection, this is displayed in green, and when Wi-Fi is disconnected, this is displayed in white. A
red “x” is displayed when Wi-Fi connection is set to off.
*4 During GPS reception, this is displayed in green, and when GPS cannot be received, this is displayed in white. In the
parking mode, a red “x” is displayed since GPS reception is set to off.
System Indicator Display
The operating status of this product is displayed with the system indicator.
System Indicator
Menu Displayed/
During Playback
Video Recording Recording Event
Error Has Occurred
(Including microSD
Card not Inserted)
Illuminated green
Illuminated red
Blinking red
Function Buttons
The functions of the function buttons are indicated by the icons displayed at the bottom of the screen.
The functions of the buttons will depend on the displayed screen. (Icons are not displayed on some screens.)
In the playback screen or MENU screen, pressing the function button returns you to the previous screen.
Recording
12 34
1 Main menu display
2 Switching of camera video
Hold down to switch Wi-Fi on/off
3 Manual recording of events
Hold down to switch microphone on/off
4 Take photo
English