Quick Start Guide

500-014720002 < 9 > 500-014720002 < 10 > 500-014720002 < 11 > 500-014720002 < 12 >
Installation
SpeciedInstallationPositiononFrontWindshield
When installing this product the inside of the front windshield, install in a vehicle and in a position that satisfies all of the
following conditions if allowed by applicable law in your location:
• Install in a 7-inch/17.8 cm square in the lower corner of the windshield farthest from the driver, a 5-inch/12.7 cm
square in the lower corner of the windshield nearest to the driver and outside of any airbag deployment zone, or in a
5-inch/12.7 cm square mounted to the center uppermost portion of the interior of the windshield. The ideal location is
behind the rearview mirror out of the driver’s view as shown below.
• A position where this entire product is within 20% of the top edge of the height of the front windshield (range within
20% of the actual length, excluding parts overlapping weatherstrips, mouldings, etc. and masked parts) or are in the
shadow of the rear view mirror as viewed from the driver’s seat.
Note that “20%” as described above is a rough estimate. Please install the product in accordance with your location’s
laws and regulations.
• A position where the lens part of this product is within the wiping range of the wiper.
• A position where the lens part of this product does not hang over the sunshade and black ceramic lines/black ceramic
pattern.
• A position where this product faces in the horizontal direction to the front and side to side.
• A position where the cigarette lighter power cable can be routed without unnecessary force.
Installation Direction
Horizontal Direction
Main Unit
Front Windshield
Ground
Main Unit
Horizontal Direction
Main Unit
Main Unit
*Install this product in a location
where it will not interfere with the
driver’s field of view,such as behind
the rear view mirror.
Installation Angle
Allowable Installation Angle:
20° to 75° (With Lens
Horizontal)
Front Windshield
Forward Direction
of Vehicle
Within 20 % of Height
Rear View Mirror
Range of Windshield Wipers
A Pillar
A Pillar
Air Bag
IMPORTANT
Always install this product in the specified installation position to ensure a safe field of view while driving and to achieve
full performance from the product.
Pioneer is not liable for any damages due to faulty or improper installation or use of the product.
Recommended Installation Position on
Rear Windshield
When installing the rear camera on the inside of the rear
window, installation in a vehicle and in a position that
satisfies all of the following conditions is recommended.
• A position where the lens part of the rear camera is
within the wiping range of the wiper.
• A position where the rear camera faces in the horizontal
direction to the rear and side to side.
• A position where the lens part of the rear camera and
the double-sided tape do not overlap the heating wires.
• A position where the rear camera connection cable can
be routed without unnecessary force.
Rear camera
Rear windshield
Connection cable
Heating wires
Wiping range of the rear wiper
Install this product
1 Clean the installation area of dirt
and oils using the included cleaning
cloth.
2 Install this product.
1 : Set the mounting bracket on the main unit.
2 : Peel off the double-sided tape release paper from the
mounting bracket.
3 : Install at the specified position of the front windshield.
Front Windshield
Mounting Bracket
Firmly push this product.
①
③
②
CAUTION
• Make sure that the surface of the front windshield is clean
and dry, before attaching the mounting bracket.
• Never touch the surface of the LCD.
• Use extreme care as the double-sided tape on the
mounting bracket is extremely strong, and should not be
reapplied once it has been applied.
• To ensure the installation strength of the adhesive tape,
leave this product for 24 hours after application before
using it.
Note
• A protective film is applied to the lens when the product
is purchased. Peel off this film.
3 Adjust the installation angle.
Loosen the angle adjustment bolt to adjust. After
adjusting, tighten the loosened bolt to secure.
Angle adjustment bolt
Removing this product
1 While pressing the protruding part as shown in the
figure below, 2 remove the main unit.
①
②
Install the Rear Camera
The top and bottom of the image can be set according
to the mounting direction of the rear camera.
1 Clean the installation area of dirt
and oils using the included cleaning
cloth.
2 Install the rear camera.
1 : Peel off the double-sided tape release paper from
the rear camera.
2 : Adjust the lens so that it faces outside the vehicle,
and install at the specified position on the rear
windshield.
1
②
Firmly push this product.
Turn this part to adjust.
CAUTION
• Make sure that the surface of the rear windshield is
clean and dry, before attaching the rear camera.
• Use extreme care as the double-sided tape on the
rear camera is extremely strong, and should not be
reapplied once it has been applied.
• To ensure the installation strength of the adhesive tape,
leave this product for 24 hours after application before
using it.
Note
• A protective film is applied to the lens when the
product is purchased. Peel off this film.
Connecting the Cables
1 Connect the cigarette lighter power
cable and rear camera connection
cable to the main unit.
Main Unit
Rear camera
Rear Camera
Connection Cable
Cigarette Lighter Power Cable
Rear camera dedicated
input terminal
Power cable
connection terminal
3 m/9 ft. 10 in.
6 m
/19 ft. 8 in.
4 m
/13 ft. 2 in.
2 Route the cigarette lighter power cable
and rear camera connection cable to the
passenger seat side.
シガーライター
電源ケーブル
アクセサリー
ソケット
Rear camera wiring example
Main Unit
Rear camera
Connection cable
3 Connect the cigarette lighter power cable
to the vehicle accessory socket.
Fully insert this into the vehicle accessory socket
to make a good connection. (The location of the
accessory socket will differ depending on the
vehicle.)
Cigarette Lighter Power Cable
Accessory socket
CAUTION
• The accessory socket will be extremely hot
immediately after using the cigarette lighter. The tip
of the cigarette lighter power cable may melt or short
circuit if it is plugged in while the socket is hot. Wait
for the socket to cool before plugging in the cigarette
lighter power cable.
4 Turn the vehicle engine on to display the
recording screen.
5 Adjust the angles of this product and of
the rear camera lens so that video outside
the vehicle is properly displayed.
To switch between camera video from the main unit
and video from the rear camera, press the switch
screen button.

“Function Buttons”
English