User Guide

Installation
SpeciedInstallationPositiononFrontWindshield
When installing this product, install in a position that satisfies all of the following conditions if allowed by applicable law
in your location:
• Install in a 7-inch/17.8 cm square in the lower corner of the windshield farthest from the driver, a 5-inch/12.7 cm
square in the lower corner of the windshield nearest to the driver and outside of any airbag deployment zone, or in a
5-inch/12.7 cm square mounted to the center uppermost portion of the interior of the windshield. The ideal location is
behind the rearview mirror out of the driver’s view as shown below.
• A position where this entire product is within 20 % of the top edge of the height of the front windshield (range within
20 % of the actual length, excluding parts overlapping weatherstrips, mouldings, etc. and masked parts) or is in the
shadow of the rear view mirror as viewed from the driver’s seat.
Note that “20 %” as described above is a rough estimate. Please install the product in accordance with your location’s
laws and regulations.
• A position where the lens part of this product is within the wiping range of the wiper.
• A position where the lens part of this product does not hang over the sunshade or the black ceramic lines/black
ceramic pattern.
• A position where this product faces in the horizontal direction to the front.
• A position where the power cable can be routed without unnecessary force.
Installation Direction
Horizontal Direction
Main Unit
Front Windshield
Ground
Main Unit
Horizontal Direction
Main Unit
Main Unit
*Install this product in a location
where it will not interfere with the
driver’s field of view,such as behind
the rear view mirror.
Installation Angle
Allowable Installation Angle:
30° to 60° (With Lens
Horizontal)
Front
Windshield
Forward Direction
of Vehicle
Within 20 % of Height
Rear View Mirror
Range of Windshield Wipers
A Pillar
A Pillar
AirBag
IMPORTANT
• Always install this product in the specified installation position to ensure a clear view of the road while driving and to
achieve full performance from the product.
Pioneer is not liable for any damages due to faulty or improper installation or use of the product.
• For vehicles equipped with driver-assistance systems, there may be areas where the installation of accessory items is
prohibited. For details, please refer to the instruction manual of your vehicle.
• Installing the Dash Camera main unit or cables near the film antenna element may affect the TV reception sensitivity.
Recommended Installation Position on Rear Windshield
When installing the 2nd camera on the inside of the rear
window, installation in a vehicle and in a position that
satisfies all of the following conditions is recommended.
• A position where the lens part of the 2nd camera is within
the wiping range of the wiper.
• A position where the 2nd camera faces in the horizontal
direction to the rear and side to side.
• A position where the lens part of the 2nd camera and the
double-sided tape do not overlap the heating wires.
• A position where the 2nd camera connection cable can
be routed without unnecessary force.
2nd camera
Rear windshield
Connection cable
Heating wires
Wiping range of the rear wiper
1 Clean the installation area of dirt and oils
using the included cleaning cloth.
■ Front windshield
■ Rear windshield
2 Install this product.
①: Set the mounting bracket on the main unit.
②: Peel off the double-sided tape release paper from the
mounting bracket.
③: Install at the specified position of the front windshield.
2
1
3
①
Front
Windshield
Firmly push
this product.
CAUTION
• Make sure that the surface of the front windshield is clean
and dry before applying the tape.
• Firmly push the area around the LCD. Next, remove this
product from the mounting bracket, and directly press
the mounting bracket against the tape. In this way, the
product can be firmly installed on the windshield.
• Never touch the surface of the LCD.
• Use extreme care as the double-sided tape on the
mounting bracket is extremely strong, and should not be
reapplied once it has been applied.
• To ensure the installation strength of the adhesive tape,
leave this product for 24 hours after application before
using it.
3 Install the 2nd camera.
①: Peel off the double-sided tape release paper from the
2nd camera.
②: Install in the specified position on the rear window so
the image of the 2nd camera is displayed horizontally
with the flat part shown in the figure (the △ on the side
faces up) facing upwards.
Note
• You can use the dedicated app to display the 2nd
camera’s image horizontally to support installation.→
“Dedicated App”
1
2
Install with the flat
surface facing
upwards.
Turn the lens towards the outside of the
vehicle and press down firmly so that the
image of the 2nd camera is displayed
horizontally.
CAUTION
• If the image of the 2nd camera is not displayed
horizontally, it may not detect approaching vehicles
behind correctly.
English
Dedicated App
The dedicated app “Dash Camera Interface” can be used to check the video recorded on this product or make settings
on the screen of an iPhone or Android device.
To use this app, a Wi-Fi connection must be made between this product and iPhone or Android device beforehand.
1 Set the Wi-Fi function of this product to on.
2 Start the dedicated app from your device.
3 Operate the device to select this product as the Wi-Fi connection device.
The SSID name (access point name) and password of this product can be checked in the Wi-Fi settings screen.
• Only one device can be connected to this product at one time. When a second device is connected, the first device
will be disconnected.
• While a Wi-Fi connection is made, no operations can be performed on this product. If a function button is pressed
while a Wi-Fi connection is made, a message will be displayed prompting you to break the Wi-Fi connection. If you
select [Yes], the Wi-Fi connection will be disconnected, and operations on this product will be enabled.
• You can change the SSID name of this product by operating the dedicated app “Dash Camera Interface”.
• It is recommended to enter the search term “Dash Camera Interface” in the search field to search for the application.
Dash Camera Interface
Check the Accessories
Main Unit×1 2nd Camera×1 Mounting Bracket×1 Power Cable
(5 m/16 ft. 5 in.)×1
2nd Camera
Connection Cable
(3 m/9 ft. 10 in.)×1*
2nd Camera
Connection Cable
(6 m/19 ft. 8 in.)×1*
microSDHC Card
(16 GB)×1
Quick Start Guide×1
Warranty×1 Cleaning Cloth×1
* The 2nd camera connection cable is included already connected.
■ During playback
56 78
5 Back
6 Previous file
7 Next file
8 Play/stop, delete
■ During MENU screen display
9a bc
9 Back
a Up*
Hold down to switch Wi-Fi on/off
b Down*
Hold down to switch microphone on/off
c Confirm
* When the volume or sensitivity MENU screen is displayed, increase or decrease the volume or sensitivity.
Inserting and Ejecting the microSD Card
Turn off the power to this product when inserting and removing the microSD card.
Inserting the microSD Card
Hold the top edge of the microSD card, position the
microSD card so that the label is facing the backside of
this product, and slowly insert it into the microSD card slot
until it clicks.
CAUTION
• Do not insert the microSD card at an angle. Doing so
may cause damage.
Ejecting the microSD Card
Slowly push in the top edge of the microSD card until
it clicks (1). The lock will be released. Pull out the
microSD card (2).
CAUTION
• Ensure care is taken when handling the microSD card,
as it could become hot after being written.