Quick Start Guide

CYR1298-A < 9 > CYR1298-A < 10 > CYR1298-A < 11 > CYR1298-A < 12 >
Installation
SpeciedInstallationPositiononFrontWindshield
When installing this product the inside of the front windshield, install in a vehicle and in a position that satisfies all of the
following conditions.
• A position where this entire product is within 20% of the top edge of the height of the front windshield (range within
20% of the actual length, excluding parts overlapping weatherstrips, mouldings, etc. and masked parts) or are in the
shadow of the rear view mirror as viewed from the driver’s seat.
Note that “20%” as described above is a rough estimate. Please install the product in accordance with your country’s
laws and regulations.
• If allowed by applicable law in your location, install in a 7-inch/17.8 cm square in the lower corner of the windshield
farthest from the driver, a 5-inch/12.7 cm square in the lower corner of the windshield nearest to the driver and outside
of any airbag deployment zone, or in a 5-inch/12.7 cm square mounted to the center uppermost portion of the interior
of the windshield. The ideal location is behind the rearview mirror out of the driver’s view as shown below.
• A position where the lens part of this product is within the wiping range of the wiper.
• A position where the lens part of this product does not hang over the sunshade and black ceramic lines/black ceramic
pattern.
• A position where this product faces in the horizontal direction to the front and side to side.
• A position where the power cable can be routed without unnecessary force.
Installation Direction
Horizontal Direction
Main Unit
Front Windshield
Ground
Main Unit
Horizontal Direction
Main Unit
Main Unit
*Install this product in a location
where it will not interfere with the
driver’s field of view,such as behind
the rear view mirror.
Installation Angle
Allowable Installation Angle:
30° to 60° (With Lens
Horizontal)
Front
Windshield
Forward Direction
of Vehicle
Within 20 % of Height
Rear View Mirror
Range of Windshield Wipers
A Pillar
A Pillar
AirBag
IMPORTANT
Always install this product in the specified installation position to ensure a safe field of view while driving and to achieve
full performance from the product.
Recommended Installation Position on Rear Windshield
When installing the 2nd camera on the inside of the rear
window, installation in a vehicle and in a position that
satisfies all of the following conditions is recommended.
• A position where the lens part of the 2nd camera is within
the wiping range of the wiper.
• A position where the 2nd camera faces in the horizontal
direction to the rear and side to side.
• A position where the lens part of the 2nd camera and the
double-sided tape do not overlap the heating wires.
• A position where the 2nd camera connection cable can
be routed without unnecessary force.
2nd camera
Rear windshield
Connection cable
Heating wires
Wiping range of the rear wiper
1 Clean the installation area of dirt and oils
using the included cleaning cloth
■ Front windshield
■ Rear windshield
2 Install this product
①: Set the mounting bracket on this product.
②: Peel off the double-sided tape release paper from the
mounting bracket.
③: Install at the specified position of the front windshield.
2
1
3
Front
Windshield
Firmly push
this product.
CAUTION
• Make sure that the surface of the front windshield is dry
before applying the tape.
• Firmly push the area around the LCD. Next, remove this
product from the mounting bracket, and directly press
the mounting bracket against the tape. In this way, the
product can be firmly installed on the windshield.
• Never touch the surface of the LCD.
• Use extreme care as the double-sided tape on the
mounting bracket is extremely strong, and it will be
difficult to reapply the tape once it has been applied.
• To ensure the installation strength of the adhesive tape,
leave this product for 24 hours after application before
using it.
3 Install the 2nd camera
①: Peel off the double-sided tape release paper from the
2nd camera.
②: With the flat part shown in the figure facing up (position
where the △ mark on the side is facing up), install
the 2nd camera at the specified position on the rear
windshield.
1
2
Install with the flat
surface facing
upwards.
Face the lens towards the outside of the
car and firmly push.
4 Connect the power cable, 2nd camera
connection cable and AV cable to this
product
2nd camera
2nd camera connection cable
Power cable
AV Cable
Main Unit
Note
• Connecting the AV cable is only required if connecting
the VREC-DZ700DC to a compatible stereo with an
AV Input.
5 Route the power cable, 2nd camera
connection cable and AV cable to the
passenger seat side
シガーライター
電源ケーブル
アクセサリー
ソケット
Main Unit
2nd camera
Connection cable
6 Connect the power cable and AV cable
→
“Connecting the Power Cable”
7 Turn the vehicle engine on to display the
recording screen
8 Adjust the angle of the lens so that video
outside and inside the vehicle is properly
displayed
Turn the angle adjustment
jog dial to adjust the lens
angle.
Turn this part to adjust
the lens angle.
Before driving, turn the lens of this product towards
the outside of the vehicle.
This product restarts when the lens angle is moved
from the outside of the vehicle to the inside, and vice
versa.
To switch between camera video from this product
and video from the 2nd camera, press the
button. →
“Function Buttons”
Note
• A protective film is applied to the lens when the
product is purchased. Peel off this film.
Connecting the Power Cable
• Be sure to disconnect the ⊖ terminal of the vehicle’s battery before connecting the power cable.
• The product should be installed by authorized service company personnel who have special training and
experience with mobile electronics products.
The parking mode (security mode allowing 24-hour, 365-day surveillance) can be used by extracting power directly from
the vehicle by the power cable.
You can also connect the product to a head unit by using an AV cable and audio output mini pin jack-RCA conversion
cable so that you can check video footage and/or the camera view using the head unit screen.*
*Do not connect the product via AV cable unless the head unit displays video input only while the vehicle is parked.
Black 0.5 m/1 ft. 8 in.
Yellow 0.5 m/1 ft. 8 in.
Red 0.5 m/1 ft. 8 in.
4.5 m/
14 ft. 9 in.
Fuse
(F 2 AL/250 V)
Fuse
(F 2 AL/250 V)
0.2 m/
7-7/8 in.
Wiring specification of
this product
Audio is recorded in
monaural sound.
Audio (L)
Audio (R)
Ground
Video
Yellow Video
White Audio (L)
Red Audio (R)
Black 5 m/16 ft. 5 in.
Ground (Black)
Securely connect to the metal part of the vehicle body.
To prevent noise, connect as close to the navigation unit
as possible.
+ Battery power supply (Yellow)
Always connect to the power circuit supplied with power
from the battery, regardless of whether the vehicle
engine switch is ON or OFF.
Accessory power supply (Red)
Connect to the power circuit supplied with power when
the vehicle engine switch is turned to the ACC position.
Never install the accessory power supply to a vehicle
that does not have an ACC position on the engine switch.
Doing so may lead to a dead battery.
Note: Connect the red and yellow lead wires to
the terminals after wiring through the vehicle’s
fuse unit.
Video/audio output mini pin jack
Connect to the AUX input of the main unit of a Pioneer
product with a mini jack terminal compatible with video
input. Connection to main units of other brands with RCA
input terminals is also possible by using the included
mini pin jack-RCA conversion cable (figure below).
*After connecting, the following message is displayed:
“Is the 3.5mm Audio/Video Jack Connected?” Select
“Yes” or “No”.
Connection Precautions
To prevent fuming and damage to the product, be sure
to first securely connect the black lead wire (Ground)
of this product to the metal part of the vehicle body.
Connect separate black lead wires (Ground) for
products with a high current consumption such as a
power amplifier. When setting up connections all at once,
there is a risk of fuming or damage to the product when
screws loosen or come off completely.
Black lead wire (Ground)
Metal part of the vehicle body
*1
*1 Not supplied for this unit
English