AUDIO/VIDEO MULTI-CHANNEL AMPLIFIER VSA-E08 Operating Instructions
IMPORTANT 1 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Quick Start Guide This is a quick guide to setting up your new amplifier so you can get home theater surround sound. For more details on any of the information presented here check the main section of the manual. Before making or changing the connections,switch off the power and disconnect the power cord from the AC outlet.
Quick Start Guide 2 Speaker Connections Home theater is designed to be setup with five, or seven speakers (front left & right; center; surround left & right; and, optimally, surround back left & right) and a subwoofer but you can use this amplifier with fewer speakers. Hook up the speakers you have to the A speaker terminals on the back of the amplifier. If you only have two speakers hook them up as "FRONT." If you have three hook up the single speaker as "CENTER." Follow the diagram on p.
Quick Start Guide 4 Digital Input Assignment This is only necessary if you did not hook up your DVD to DIGITAL IN 1, as in the first diagram on p. III. 1 AMP DVD/LD Amplifier TAPE 2 MONITOR MAIN INPUT ATT. SUB FL DIMMER REMOTE SETUP MD/TAPE1 BASS TV/SAT 1 Turn on the amplifier and your TV, press the AMP button on the remote control. 2 2 Press the SUB button on the remote control.
Quick Start Guide 5 Playing a DVD with Surround Sound 1 Turn on the Amplifier, your TV, and the DVD player. 2 Press the STANDARD button on the front panel for the basic surround sound setting. You can also press the remote control AMP button and then press the STANDARD button on that Amplifier MAIN screen. 3 Press the DVD/LD button on the remote control. You should see "DVD/LD" in the display on the amplifier. 4 Play a DVD.
Table of Contents Features .............................................. 8 Before You Start ................................. 9 Connecting Your Equipment ............. 12 Displays & Controls ........................... 21 Initial Set Up ....................................... 27 On Screen Display .................................................... 27 Switching video system between PAL and NTSC .................................................. 27 Setting Up the Remote Control ..........................
Features Multi Channel Stereophonic Concept The VSA-E08 amplifier is constructed with Pioneer’s industry-leading multi channel stereophonic concept. This well-developed approach to amplifier circuitry takes the high level base technology that, up until now, has been only used for stereo equipment and applies it to multi-channel audio-visual amplifiers.
Before You Start Checking the Supplied Accessories Please check that you have received all of the following supplied accessories. “AA” IEC LR6 batteries x 4 Remote control unit PREPARATION Touch pen (Attached to the back of the remote control) Cushion for Remote x 4 Operating Instructions How to Use This Manual This manual is for the VSA-E08 Audio/Video MultiChannel Amplifier. This manual is divided into three main sections which will tell you how to setup and use the unit : Playback“ on p.41.
Before You Start Remote Control Battery Alarm When the batteries get too weak to operate the remote control properly an alarm will sound and a warning screen will appear on the remote. Change the batteries as shown on the previous page. Change Battery !! SIZE AA, LR6 The Touch Pen & Lock The touch pen is located in the back right-hand corner of the remote control. Take it out by sliding your finger along the bottom right edge of the remote control and then grasping the pen with thumb and forefinger.
Before You Start The PIONEER SR System: Operating other PIONEER components Connecting an optional control cord allows you to operate other PIONEER components simply by pointing the amplifier’s remote control at the remote sensor on the front panel of the amplifier. The amplifier then sends the remote control signals to the other devices via the CONTROL OUT terminal. PREPARATION IN OUT CONTROL CONTROL IN OUT Amplifier PIONEER component bearing the Î mark.
Connecting Your Equipment Before making or changing the connections, switch off the power and disconnect the power cord from the AC outlet. Audio Components To begin set up connect your audio components to the jacks as shown below. These are all analog connections and your analog audio components (turntable, cassette deck) use these jacks.
Connecting Your Equipment Digital Connections PREPARATION In order to use Dolby Digital/DTS soundtracks which are at the heart of home theater you need to make digital audio connections. You can do this by either a coaxial or an optical connection (you don’t need to do both).
Connecting Your Equipment Example Connection for a DVD/LD or LD player Make sure you connect your DVD/LD or LD players using both the 2 RF jack and either a coaxial or optical (you don't need to do both of these) digital connections. If your player has an 2 RF output this will ensure you can use all LDs (see p.15). We also recommend hooking up your digital components to analog audio jacks. Before making or changing the connections, switch off the power and disconnect the power cord from the AC outlet.
Connecting Your Equipment Video Components PREPARATION Connect your video components to the jacks as shown below. Regarding a DVD there are two types of connections to make. Hook up your video signal with either component video, S-video, or composite video cords (the quality descends in this order) but remember, the video component you are watching and your TV must be hooked up with same type of video cord or you won't be able to see the picture.
Connecting Your Equipment Satellite TV Components Connect your satellite TV components to the jacks as shown below. Hook up the video signal with either component video, S-video, or composite video cords (the quality descends in this order) but remember, the video component you are watching and your TV must be hooked up with same type of video cord or you won't be able to see the picture.
Connecting Your Equipment TV AUDIO R 2 RF IN (AC-3) IN 1 IN 2 IN 3 IN 4 VIDEO L IN 5 VIDEO COMPONENT VIDEO DVD/LD TV/SAT IN IN Y S VIDEO DVD / LD IN IN TV / SAT IN IN PB IN IN PR PRE OUT SURROUND R L MULTI CH IN VIDEO IN FRONT OUT 1 OUT 2 PREPARATION Connect your TV to the jacks as shown below.
Connecting Your Equipment Speakers A full complement of eight speakers is shown here but, naturally, everyone's home set up will vary. Simply connect the speakers you have in the manner described below. The VSA-E08 will work with just two stereo speakers (called "front" speakers in the diagram) but the amplifier is designed to be used with at least three speakers. One of the latest features of home theater is the use of SURROUND BACK speakers.
Connecting Your Equipment 7 Speaker terminals 1 Twist exposed wire strands together. 3 Tighten terminal. 2 Loosen speaker terminal and insert exposed wire. PREPARATION 10mm Placing Your Speakers Proper speaker placement is essential to realize the best sound from your system. The diagram and tips given here are just a rough guide; be sure to read the instructions that come with your speakers.
Connecting Your Equipment Connecting additional amplifiers To hook up surround back speakers you need to use an additional amplifier. Other than for that purpose this amplifier has more than sufficient power for any home use, but it is possible to add additional amplifiers to every channel of your system. Make the connections shown below to add amplifiers to power your speakers. Before making or changing the connections, switch off the power and disconnect the power cord from the AC outlet.
Displays & Controls Display All the display information is explained and/or referenced here. 2 34 5 6 SIGNAL ATT LOUDNESS SELECT OVER H.P ANALOG SP DIGITAL AC-3RF AUTO 7 MIDNIGHT 8 9 10 DSP STEREO 12 11 VOLUME PRO LOGIC AB 13 PREPARATION 1 DIGITAL dB MPEG TAPE 2 AC-3DTS MPEG L C R LS S RS LFE 14 1 SIGNAL SELECT indicators Light to indicate the input signal you selected of the source signal. ANALOG : Lights when analog signals are assigned.
Displays & Controls Front Panel All the controls on the front panel are explained and/or referenced here. To open the front panel push gently on the lower third of the panel.
Displays & Controls 4 TONE control buttons TONE button CHANNEL SELECT button Switches the tone adjust controls between the FRONT, CENTER, SURROUND and SURROUND BACK speakers. You can then use the BASS and TREBLE controls to adjust the sound. BASS (–/+) buttons (See p.49) Use to adjust low frequencies. TREBLE (–/+) buttons (See p.49) Use to adjust the high frequencies. 5 LOUDNESS button (See p.49) Switches the LOUDNESS mode on or off. Can not be used in THX, MULTI CH IN. DIGITAL NR button (See p.
Displays & Controls Remote Control These pages describe the buttons on the remote control used to operate the amplifier. Since the screen on this LCD remote control changes when you select a different function, explanations of buttons for controlling other components/functions can be found in the sections for those components/functions.
Displays & Controls Basic Amplifier LCD Screens Amplifier MAIN Screen 2 3 Amplifier DSP MAIN THX 5 SUB STEREO / dts / MPEG 4 EFFECT 4 ADVANCED STANDARD THEATER MIDNIGHT MULTI CH IN DIGITAL NR SIGNAL SELECT LOUDNESS 6 PREPARATION 1 0 9 7 8 1 Amplifier MAIN button Press this button to select the main amplifier screen (above) when the remote control is on the sub amplifier screen. 8 2/dts/MPEG buttons (See p.
Displays & Controls Amplifier SUB Screen 1 Amplifier 2 TAPE 2 MONITOR 4 1 Amplifier SUB button Press this button to select the sub amplifier screen (above) when the remote control is on the main amplifier screen. 2 TAPE 2 MONITOR button (see p.66) Selects the tape deck (or MD recorder, etc.) connected to the TAPE 2 MONITOR inputs/ outputs. Allows monitoring of a recording as it's being made. 3 FL DIMMER button (See p.51) Use to adjust the brightness of the main display.
Initial Set Up On Screen Display There are a number of possible ways to hook up the amplifier to your video components, like a DVD player, and hook up to your amplifier to your TV, but some of them won't allow you to use the on-screen display of this unit. To avoid this one simply needs to follow two rules. 1 Always use the same type of video cords to hook up your video components to the amplifier as you use to hook up the amplifier and your TV.
Initial Set Up Setting Up the Remote Control Since this remote is based on LCD screens, you should try and get used to the touch-sensitive nature of the buttons as well as the way in which different screens control different operations. You can move between the different screens with the function buttons on the left and right and/or certain buttons within each screen. The BACK button will always return the remote control to the previous screen.
Initial Set Up 5 Decide which other adjustments you‘d like to make and press those buttons.
Initial Set Up Setting Up for Surround Sound To ensure the best possible surround sound, complete the following set up operations. You only need to make these settings once (unless you change the placement of your current speaker system or add new speakers, etc.). These set up operations use your TV to display the settings and choices so be sure your TV and amplifier are properly hooked up.
Initial Set Up DIGITAL INPUT SELECT In order to be able to use your digital equipment properly you need to assign digital inputs for each of the digital components you connected. Match the DIGITAL IN buttons 1-5 with the digital jacks 1-5 in accordance with what component is hooked up to each digital jack. Check the digital terminal numbers on the back of the amplifier to make certain what component is in which jack (if necessary, see p.10 for more on digital connections).
Initial Set Up SPEAKER SETTING The following steps show you how to select the correct set up for the type and number of speakers you connected. If continuing from DIGITAL INPUT SELECT go to step 1. If starting fresh, complete steps 1-3 on p.30 first. System Setup BACK 1 Press the SPEAKER SETTING button. DIGITAL INPUT SELECT 1 SPEAKER SETTING CROSSOVER NETWORK BASS PEAK LEVEL MANAGER DYNAMIC RANGE CONTROL CHANNEL DELAY CHANNEL LEVEL 2 Select the THX or FREE setting.
Initial Set Up ONE (SINGLE) SURROUND BACK SPEAKER Sub woofer Center Front R Speaker Setting Front L + BACK + + THX FREE Surround L Surround R + + + SETUP OK Surround back NO SURROUND BACK SPEAKERS Sub Center woofer Front R Speaker Setting Front L + + BACK + THX FREE Surround L Surround R + + Surround back (not hooked up) Speaker Setting + + BACK + THX FREE + + + + SETUP OK 4 « Speaker Setting + + BACK + THX FREE + + + + SETUP OK memo If you have a subwoofer and
Initial Set Up CHANNEL DELAY Adding a slight delay to some speakers is necessary to achieve a surround sound effect. You need to figure out the distance from your listening position to your speakers to add the proper delay. The following steps show you how to set the delay time for each channel by specifying the distances from your listening position to each speaker. Once you specify the speaker distances, the amplifier calculates the correct delay times automatically.
Initial Set Up CHANNEL LEVEL The following steps show you how to balance the sound output level of your speakers. Proper speaker balance is essential for obtaining high quality surround sound. If continuing from CHANNEL DELAY go to step 1. If starting fresh, complete steps 1-3 in “Setting Up for Surround Sound“ (p.30) first. 1 Press the CHANNEL LEVEL button. System Setup The CHANNEL LEVEL settings will appear on your remote control screen.
Initial Set Up 3 AUTO T.TONE MANUAL T.TONE 3 Using the remote control display, follow the instructions below to adjust the speaker levels so that you hear the test tone at the same volume from each speaker when seated in your normal listening position. NOTE : The volume of the subwoofer tends to sound lower than it actually is. You may need to adjust the level after testing with an actual soundtrack. In AUTO mode 1 Use the +/– (or 5˜∞) buttons to adjust the level of the speaker outputting the test tone.
Initial Set Up CROSSOVER NETWORK The following steps show you how to adjust the crossover network. The crossover network is the frequency at which the system divides the signal and sends the different parts (high, mid, low) to different speakers. Speaking precisely, this setting sets the cutoff point for the bass frequencies rerouted from your SMALL speakers to your subwoofer or speaker set to LARGE. If continuing from CHANNEL LEVEL go to step 1.
Initial Set Up BASS PEAK LEVEL MANAGER The LFE (Low Frequency Effect) channel in Dolby Digital,DTS or MPEG program sources can produce heavily concentrated ultra-low bass tones that may exceed the capabilities of your speaker system. The following steps show you how to set the peak level for the ultra-low bass (LFE) channel. If continuing from CROSSOVER NETWORK go to step 1. If starting fresh, complete steps 1-3 in "Setting Up for Surround Sound" (p.30) first.
Initial Set Up DYNAMIC RANGE CONTROL This feature makes it possible to enjoy full surround sound effects on Dolby Digital sources even at low volumes. It does this by compressing the dynamic range. Dynamic range is the difference between the loudest and the softest sounds in any given signal. Compressing the range plays sounds so the quieter ones are audible and the louder ones don’t get distorted or become overpowering.
Initial Set Up DUAL MONO SETTING The dual mono setting can only be used when listening to Dolby Digital discs that have dual mono software encoded in them. Dual mono software usually is used to put two different soundtracks on one DVD. With this setting you can choose which channel in the dual mono setting you want to listen to. Thus, it is useful for soundtracks that have one language on one channel and a different language on the other.
Basic Playback Sound Modes The five sound modes on the receiver are explained here. These can be turned on from the front panel or from the AMPLIFIER MAIN SCREEN on the remote control. There are three cinema modes: STANDARD, HOME THX CINEMA, and ADVANCED THEATER. These are designed to be used with multi channel surround sound audio/visual sources (like DVDs and LDs). Intrinsic to home theater, these modes can deliver realistic and powerful surround sound that recreates the movie theater experience.
Basic Playback HOME THX CINEMA modes THX is a set of technical standards created by Lucasfilm, Ltd. These standards were designed to emulate a film sound stage and thus reproduce, with the greatest possible accuracy, the soundtrack intended by the filmmakers. To get THX sound use one the three modes explained below. You will only be able to access the second two modes if you have hooked up SURROUND BACK speakers. For more detailed information see p.18,20,32-33.
Basic Playback DSP modes The DSP (Digital Signal Processing) modes allow you to transform your living room into a variety of different sonic environments when playing either two-channel or multi-channel sources. If you have SURROUND BACK speakers switched on (see p.32-33) then 7.1 will appear after the name of all of these modes in the display on the amplifier. HALL 1 Simulates the acoustic effects of a large concert hall. Suitable for classical music.
Basic Playback Selecting a Sound Mode To ensure the best possible surround sound, be sure to complete the set up procedures described in “Setting Up for Surround Sound” (starting on page 30) before using the sound modes. This is particularly important when using the 2(Dolby) Digital / MPEG or DTS sources. When using the sound modes, using SPEAKERS A will give the best results. If you use SPEAKERS B the sound will be down mixed to the two front B speakers. Using surround sound 1 Press the AMP.
Basic Playback Playing Sources with Dolby Digital, MPEG or DTS Sound The following instructions show you how to play Dolby Digital, MPEG or DTS sound sources with the VSA-E08. use 4 1 Turn on the power of the playback component.
Basic Playback Playing Sources with Stereo Sound The following instructions show you how to play audio or audio-visual sources with the VSA-E08. memo 4 If the TAPE 2 indicator is visible in the display, it means the TAPE 2 MONITOR is on. Press TAPE 2 MONITOR on the front panel to turn it off unless you want to listen to TAPE 2. use 1 Turn on the power of the playback component.
Basic Playback Switching ANALOG/DIGITAL Signal Input This button selects the type of input, ANALOG, DIGITAL or 2 RF, sent to the amplifier. You need to take special care to switch to the appropriate input when necessary. For example, the switch would have to be on DIGITAL to hear DOLBY DIGITAL/MPEG or DTS surround sound material but it would have to be on analog to record from the ANALOG out jacks on the amplifier.
Basic Playback Reducing Noise During Playback (DIGITAL NR Function) To reduce extraneous noise switch on DIGITAL NR. This noise reduction can be used with every mode except THX and MULTI CH IN. 1 Press the DIGITAL NR button on the remote control’s Receiver MAIN screen or on the front panel. MAIN Amplifier MAIN DSP SUB Each press switches DIGITAL NR on or off.
Basic Playback Listening in LOUDNESS Mode The LOUDNESS mode allows you to boost the bass in a signal. It is useful for listening to music at low volumes. MAIN Amplifier MAIN DSP SUB STEREO / dts / MPEG THX EFFECT Press the LOUDNESS button on the remote control’s Amplifier MAIN screen or on the front panel. Each press switches LOUDNESS mode on or off.
Basic Playback MULTI CHANNEL IN Playback MULTI CH IN allows you to connect an external decoder to enjoy certain types of specialized discs. To use MULTI CH playback follow the instructions below. MAIN Amplifier DSP MAIN Press the MULTI CH IN button on the remote control’s Amplifier MAIN screen or the MULTI CH INPUT button on the front panel.
Basic Playback Direct Playback MAIN STEREO Amplifier DSP MAIN SUB STEREO / dts / MPEG THX EFFECT ADVANCED STANDARD THEATER MULTI CH IN MIDNIGHT DIGITAL NR SIGNAL SELECT LOUDNESS Use the STEREO button on the remote control or the STEREO/ DIRECT button on the front panel to alternate between STEREO and DIRECT mode. The DIRECT mode will give you the most accurate reproduction of two channel (stereo) sources but won't let you add any effects to the sound.
Remote Control of Other Components Setting Up the Remote Control to Control Other Components In addition to controlling the amplifier, the supplied remote control can operate your other components (VCR, TV, LD, CD, etc.) after you program it to do so. In this way, instead of fumbling with many different controls and buttons, you only need to use one remote control. If your component(s) are listed in the remote control's memory, simply follow the steps below.
Remote Control of Other Components 5 Select the name of the company that makes your component.
Remote Control of Other Components Learning Mode: Programming Signals from Other Remote Controls If preset codes are not available for your component(s), or the available preset codes do not operate correctly, you can use this procedure to program in signals from the remote control(s) of your other component(s). These steps can also be used to add further operations to the remote control screens that were successfully set with the stored settings (see p.52-53). 1 Press the REMOTE SETUP.
Remote Control of Other Components 5 AMP 6 DVD:OK BACK DVD/LD REMOTE SETUP 1 2 3 MD/TAPE1 4 5 6 CD TV/SAT SEARCH MODE VCR1 TOP MENU 7 8 9 LINE/ TUNER SET UP 10 0 C TV CONTROL MENU VCR2 7 Learning AMP REMOTE SETUP DVD/LD MD/TAPE1 TV/SAT CD VCR1 LINE/ TUNER VCR2 TV CONTROL 5 Point the two remote controls toward each other. Press the button on the other remote control corresponding to the operation you want to program.
Remote Control of Other Components Item Memo Use the ITEM MEMO capability to add more infomation to the remote control display screens for different functions, like your DVD or CD player. For example, you could add the name of the company that makes your component, then the top line of the screen for the respective component would read something like "DVD PIONEER" .
Remote Control of Other Components Key Rename Use the KEY RENAME capability to rename the buttons (keys) on the remote control screens for different functions (DVD, etc.). You would want to do this if you taught a specific button a new operation on the previous two pages. For example, you could teach the SEARCH MODE button to be an audio key and the rename it "AUD".
Remote Control of Other Components Using Remote Control with Other Components DVD or LD player operations • The following operations are available from the Amplifier’s remote control after you program your DVD or LD player into it, but some operations may need to be learned separately by the amplifier (see “Setting Up the Remote Control to Control Other Components,“ p.52-55). • To perform these operations, press the DVD/LD button to set the remote to the DVD or LD operation mode.
Remote Control of Other Components CD player operations memo • The following operations are available from the Amplifier’s remote control after you program your CD player into it, but some operations may need to be learned separately by the amplifier (see “Setting Up the Remote Control to Control Other Components,“ p.52-55). • To perform these operations, press the CD button to set the remote to the CD operation mode.
Remote Control of Other Components MD operations memo • The following operations are available from the Amplifier’s remote control after you program your MD recorder into it, but some operations may need to be learned separately by the amplifier (see “Setting Up the Remote Control to Control Other Components,“ p.52-55). • To perform these operations, press the MD/TAPE1 button to set the remote to the MD operation mode.
Remote Control of Other Components TV operations • The following operations are available from the Amplifier’s remote control after you program your TV into it, but some operations may need to be learned separately by the amplifier (see “Setting Up the Remote Control to Control Other Components,“ p.52-55). • To perform these operations, press the TV/SAT or TV CONTROL button to set the remote to the TV operation mode.
Remote Control of Other Components STB (satellite tuner) operations memo 4 3 • The following operations are available from the amplifier's remote control after you program your satellite tuner into it, but some operations may need to be learned separately by the amplifier (see “Setting Up the Remote Control to Control Other Components,“ p.52-55). • To perform these operations, press the TV/SAT button to set the remote to the SAT operation mode.
Remote Control of Other Components Tuner operations memo • The following operations are available from the amplifier's remote control after you program your FM/AM tuner into it, but some operations may need to be learned separately by the amplifier (see “Setting Up the Remote Control to Control Other Components,“ p.52-55). • To perform these operations, press the LINE/TUNER button to set the remote to the CD operation mode.
Remote Control of Other Components Cassette deck operations You can use this remote control to control a single or a double cassette deck after you program the deck player into it. If you have a regular cassette deck with only one set of tape heads use the buttons on the right marked “SINGLE/DECK II“. If you have a double cassette deck with use the buttons on the left for deck I and the buttons on the right for deck II.
Remote Control of Other Components VCR operations memo • The following operations are available from the Amplifier’s remote control after you program your VCR deck into it, but some operations may need to be learned separately by the amplifier (see “Setting Up the Remote Control to Control Other Components,“ p.52-55). • To perform these operations, press the VCR 1 or VCR 2 button to set the remote to the VCR operation mode.
Using Other Functions Recording from Audio Components The following explanations show you how to record an analog or digital audio signal. Note that your analog components cannot record a player that is only connected digitally (and vice-versa). If you want to record from a digital component to an analog one (for example, a tape deck), or vice-versa, the digital component it must be connected via analog jacks and you need to set the SIGNAL SELECT switch to ANALOG.
Using Other Functions Video Select This function allows you to listen to one sound source while you watch a different video source on your TV. The sound source is set in the normal fashion as is explained on p.45. You then alter the video input with the VIDEO SELECT button. Press the VIDEO SELECT button on the front panel to cycle through the different possible video inputs. The first press shows the video input you are currently using.
Using Other Functions Multi Operations Multi operations allow you to tell the amplifier and your other components to do a number of things with the push of only two buttons on the LCD commander. For example, you can program the unit to turn on your TV, turn on your DVD player and start playing the loaded DVD. This allows you to freely decide which operations you want performed as well as the order in which you want them performed.
Using Other Functions 6 DVD:Multi Operation AMP DVD/LD TV/SAT SEARCH MODE VCR1 TOP MENU VCR2 MENU SETUP BACK 1 2 3 MD/TAPE1 4 5 6 CD 7 8 9 LINE/ TUNER 10 0 C TV CONTROL Multi Operation [ DVD/LD ] AMP 6 Select a command from the screen of the component (for example 3 [play]). REMOTE SETUP BACK The command and component chosen will appear in the window of command 1. To erase a command Press the command button you want to erase and press the CLEAR button.
Using Other Functions System OFF The SYSTEM OFF feature allows you to tell the receiver and your other components to stop and turn off with the push of only one button on the LCD commander (this feature will only work with components that have a standby mode). For example, you can program the unit to stop your DVD, turn off your TV, turn off your DVD player and turn off the receiver itself. You don't need to program in other the power for PIONEER components, they will go off automatically in this mode.
Using Other Functions AMP DVD:System Off DVD/LD BACK 1 2 3 MD/TAPE1 4 5 6 CD TV/SAT SEARCH MODE VCR1 TOP MENU 7 8 9 LINE/ TUNER SET UP 10 0 C TV CONTROL MENU VCR2 6 AMP 6 Select a stop or a power ( ) command. REMOTE SETUP The command and component chosen will appear in the window of command 1. To erase a command Press the command button you want to erase and press the CLEAR button. To go back one step Press the BACK button.
Using Other Functions Setting up the DIRECT FUNCTION The direct function will not be necessary for most users. It is designed in case you have an external video source connected to your TV (a video source that is not going through the VSA-E08). For this explanation we'll call this the "external video deck." You'd like to control external video deck with this unit's remote control so you've assigned it a function button (for example purposes, the VCR 2 button).
Techno Tidbits & Problem-solving 1 Dolby Digital Dolby Digital is a compression format which records the sound of 6 or 8 channels of the theater surround system (Dolby Digital) on the movie film digital track. Of the 6-8 channels, the sub woofer channel is intended for bass only, and because the frequency range is smaller than a main channel, the overall soundtrack is expressed as 5.1 or 7.1 channels.
Techno Tidbits & Problem-solving R DTS DTS has been adopted as a sound recording format in the latest movie theaters since the release of “JURASSIC PARK” in 1993, and has a good reputation for high quality sound and dynamic surround effects. In this system, 6 channels of digital sound are recorded on CD-ROM, rather than on the film. DTS adopts a simultaneous playback format. With a low rate of compression of sound signals and a high rate of transmittance, a higher sound quality format is produced.
Techno Tidbits & Problem-solving Troubleshooting Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service center or your dealer to carry out repair work.
Techno Tidbits & Problem-solving Symptom No sound from surround or center speakers. Cause • Speaker settings are incorrect. • The rear and/or center levels are turned down. • The surround and/or center speakers are disconnected. Sound is produced from some components, but not from digital components. • SIGNAL SELECT is set incorrectly. • The digital inputs are assigned incorrectly, or not at all. No sound is output or a noise is output when software with DTS is played back.
Techno Tidbits & Problem-solving Specifications Amplifier Section Continuous Power Output (STEREO MODE) FRONT ... 130 W + 130 W (DIN 1 kHz, THD 1 %, 6 Ω) Continuous Power Output (SURROUND MODE) FRONT ... 130 W + 130 W (DIN 1 kHz, THD 1 %, 6 Ω) CENTER ................ 130 W (DIN 1 kHz, THD 1 %, 6 Ω) SURROUND ....................................... 130 W + 130 W (DIN 1 kHz, THD 1 %, 6 Ω) Rated Power Output .............................. 100 W + 100 W (20 Hz-20 kHz, THD 0.
Published by Pioneer Corporation. Copyright © 2000 Pioneer Corporation. All rights reserved. PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS [USA] INC. P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. PIONEER ELECTRONICS OF CANADA, INC. 300 Allstate Parkway, Markham, Ontario L3R OP2, Canada PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11 PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
