Owner's Manual

< 9 > < 10 > < 11 > < 12 >
Mounting to Dashboard
•
Protective film is affixed to the suction surface
(back side) of the suction cup. Do not peel off
the film until step 10. If the suction surface of the
suction cup becomes dirty, the suction power will
be reduced and the product may fall.
•
Select the following location to install the
product. If the product is not installed correctly,
it will fall, etc.
* Smooth and level location on the dashboard
* Location where the entire suction surface can
be affixed
•
Be sure to attach the supplied safety strap to
prevent the product from falling.
1
Turn the nut counterclockwise
and remove it.
2
Assemble the dashboard
mount attachment and
nut, and insert them into
the attachment hole of the
product.
3
Fix them in place by turning
the nut clockwise.
4
Determine the mount position.
Deter mine the mount position of the product
by plac
ing the attachment on the dashboard
without removing the film.
5
Adjust the angle and height.
Loosen each of the screws for the angle 1
and height 2, make adjustments, and then
tighten the screws.
1
2
6
Pass the safety strap through
the hole in the suction cup
surface mount sheet and
fasten the strap.
Pass the shortest loop of the safety strap
through the hole in the suction cup surface
mount sheet and fasten the strap.
7
Pass the other end of the
safety strap through the
gap in the dashboard mount
attachment and fasten the
strap.
Pass the longest loop of the safety strap
through the gap in the dashboard mount
attachment, pass the suction cup surface
mount sheet at the other end through the
loop, and fasten the strap.
8
Peel off the double-sided tape
release paper on the back of
the suction cup surface mount
sheet and affix the suction cup
surface mount sheet to the
dashboard.
•
Affix the suction cup surface mount sheet
to the desired mounting position.
•
Wipe clean and dry the affixing location
before affixing.
•
After affixing the suction cup surface
mount sheet, firmly press the entire
affixing surface to push out any air.
•
Select the following location to affix the
suction cup surface mount sheet.
* Smooth and level location on the
dashboard
* Location where the entire suction
surface can be affixed
9
Raise the suction surface lock
lever.
10
Peel off the film from the
suction surface and place the
suction surface on the suction
cup surface mount sheet.
11
Lower the suction surface
lock lever to lock the suction
surface in place.
Move the product up, down, left, and right to
check that it does not rattle.
Connecting
1
Insert the supplied USB
charger into the vehicle’s
cigarette lighter socket.
Cigarette
lighter socket
Use the supplied USB charger to perform
quick charging. Quick charging may not
be possible with a charging port fitted to
the vehicle as standard or a commercially
available USB charger with an insufficient
voltage/current because USB output
equivalent to the product input specification is
required.
2
Connect the USB input port
of this product and the USB
charger with the supplied
USB Type-C Cable.
When inserting the USB connector into this
product, insert it until you hear a click. When
the cable is connected, the power lamp and
charging lamp will illuminate. For details
on illumination status, see “Product Status
Display”.
Turning the Power On and Off
Turning the Power On
1
Press the power button.
The power lamp (blue) lights. For details
on illumination status, see “Product Status
Display”.
Power button
Power lamp
•
Normally, when the vehicle’s engine is
turned on (ACC ON), power is supplied
from the USB charger and the product
power turns on automatically.
•
When the product power on state
continues for 5 minutes after power stops
being supplied from the USB charger, the
product power will turn off automatically.
•
If the charge of the electric double-layer
capacitor has run out due to opening
and closing the arms several times while
there is no power supplied from the USB
charger, the product power will not turn on.
Turning the Power Off
1
Press and hold down the
power button for 3 seconds.
The power lamp (blue) goes out and the
power turns off.
Installation