User manual

34
Connecting your equipment
03
! When connecting to an HDMI/DVI-compatible monitor using the HDMI OUT 2 terminal, switch the HDMI
output setting to OUT 2 or OUT 1+2. See Switching the HDMI output on page 83 .
In the same way, when an HDMI/DVI-compatible monitor is connected to the HDMI OUT 3 terminal, switch
the HDMI OUT 3 setting to ON (page 83 ). In this case, MAIN/HDZONE at ZONE Setup must be set to MAIN
(page 108 ).
! For input components, connections other than HDMI connections are also possible (see Connecting your DVD
player with no HDMI output on page 34 ).
! If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables.
— When the TV and receiver are connected by HDMI connections, if the TV supports the HDMI ARC (Audio
Return Channel) function, the sound of the TV can be input to the receiver via the HDMI OUT terminal, so
there is no need to connect an audio cable. In this case, set ARC at HDMI Setup to ON (see HDMI Setup on
page 74 ).
After setting the ARC, some time may be required for the connected device to be recognized and the sound to
be produced.
— If you use a coaxial digital audio cable or RCA (analog) audio cable, you’ll need to tell the receiver which digi-
tal or analog audio input you connected the TV to (see The Input Setup menu on page 50 ).
— Please refer to the TV’s operation manual for directions on connections and setup for the TV.
! If the TV to be connected using HDMI supports 4K/60p, you can switch the 4K/60p signal output setting in
accordance with TV performance. When the 4K/60p setting is changed to 4:4:4, the video image may not be
output normally unless the HDMI cable supports 4K/60p 4:4:4 24 bit (18 Gbps transmission). In such a case,
select 4:2:0 (page 83 ).
! You cannot input 4K/60p 4:4:4 24 bit video from HDMI IN 3 to the IN 7 terminal. Use the BD IN, HDMI IN 1 or
HDMI IN 2 terminal.
! The HDMI OUT 3 terminal outputs 4K/60p 4:4:4 24 bit video when MAIN/HDZONE is set to MAIN. When it is
set to HDZONE, the 4K/60p 4:4:4 24 bit video is not output.
Connecting your DVD player with no HDMI output
This diagram shows connections of a TV (with HDMI input) and DVD player (or other playback component with no
HDMI output) to the receiver.
LAN
(
10/100
)
OUT 3
(HDZONE)
OUT 2OUT 1
(CONTROL)
DC OUTPUT
for WIRELESS LAN
(
OUTPUT 5 V
0.6 A MAX
)
(
OUTPUT 5 V
0.9 A MAX
)
OPTICALCOAXIAL
SELECTABLE
ASSIGNABLE
ASSIGNABLE ASSIGNABLE
DVR/BDR
INOUT
MONITOR
OUT
COMPONENT VIDEO
P B Y
P
R
IN
1
(
DVD
)
BD IN IN
2
(
SAT/CBL
)
IN
3
(
DVR/BDR
)
IN
6
IN
4
IN
7
MHL
IN
1
(
TV
)
IN
2
(
DVR/BDR
)
IN
1
(
DVD
)
IN
2
(
SAT/CBL
)
IN
1
(
DVD
)
IN
2
(
DVR/
BDR
)
OUT
HDMI
ASSIGNABLE
1
-
7
ASSIGNABLE
DVR/BDR
INOUT
MONITOR
OUT
P B Y
P
R
IN
1
(
DVD
)
IN
2
(
DVR/
BDR
)
LAN
(
10/100
)
OUT 3
(HDZONE)
OUT 2OUT 1
(CONTROL)
DC OUTPUT
for WIRELESS LAN
(
OUTPUT 5 V
0.6 A MAX
)
(
OUTPUT 5 V
0.9 A MAX
)
OPTICALCOAXIAL
SELECTABLE
ASSIGNABLE ASSIGNABLE
IN
1
(
DVD
)
BD IN IN
2
(
SAT/CBL
)
IN
3
(
DVR/BDR
)
IN
6
IN
4
IN
7
MHL
IN
1
(
TV
)
IN
2
(
DVR/BDR
)
IN
1
(
DVD
)
IN
2
(
SAT/CBL
)
OUT
COMPONENT VIDEO
HDMI
ASSIGNABLE
1
-
7
HDMI IN
DIGITAL OUT
COAXIAL
OPTICAL
ANALOG
RL
AUDIO OUT
VIDEO
VIDEO OUT
Y
PB
PR
COMPONENT VIDEO OUT
HDMI/DVI-compatible monitor
DVD player, etc.
Select oneSelect one
! With factory default settings, video from the video cable or component cable will not be output from the HDMI
terminal. To output video, you must switch video input to the device connected with the video cable or compo-
nent cable and set V.CONV to ON (page 80 ).
! If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables
(page 33 ).
— When the TV and receiver are connected by HDMI connections, if the TV supports the HDMI ARC (Audio
Return Channel) function, the sound of the TV can be input to the receiver via the HDMI OUT 1 terminal, so
there is no need to connect an audio cable. In this case, set ARC at HDMI Setup to ON (see HDMI Setup on
page 74 ).
! If you use an optical digital audio cable or RCA (analog) audio cable, you’ll need to tell the receiver which digi-
tal input you connected the player to (see The Input Setup menu on page 50 ).
! If HDZONE is set to on, video images connected using a video cable or component cable are not output from
the HDMI terminal. To output video images, turn HDZONE off (page 84 ).