PWM-T210 Installation Instructions UNIVERSAL FLAT PANEL MOUNT IN-PWMT210.
PWM-T210 TABLE OF CONTENTS Warning Statements Parts List Installation Tools Locating the Center of the Display Mounting Bracket Positioning Securing the Mounting Brackets Marking the Wall Marking the Bottom Mounting Points Securing the Lower Wall Plate Securing the Upper Wall Plate Mounting the Display Securing the Display Technical Specifications Warranty Contact Premier Mounts Page 2 3 4 4 5 5 6 7 7 8 8 9 10 11 11 11 Installation Instructions
PWM-T210 Safety Precautions This wall mount should be installed by qualified personnel having sufficient skill and competence to install it. Qualified installation specialists or your dealer should install the mount and set up the plasma display in order to avoid personal injury or property damage. Premier does not assume liability for injury or damage, including liability, caused by improper installation, mounting or setup of the plasma display, misuse, modification or natural disasters.
PWM-T210 Parts List NOTE: This mount is shipped with all installation hardware and components. Make sure that none of these parts are missing and/ or damaged before beginning installation. If there are parts missing and/or damaged, please stop and contact Premier Mounts (800) 368-9700.
PWM-T210 Locating the Center of the Display CAUTION: Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result in serious personal injury and possible damage to the flat panel. WARNING: INVERT THE FLAT PANEL PLACE IT ON A SOFT, FLAT SURFACE TO PREVENT DAMAGE TO THE FLAT PANEL. USE A BLANKET, FOAM, ETC. FAILURE TO DO SO WILL RESULT IN DAMAGING THE FLAT PANEL.
PWM-T210 Display Bottom CL Mounting Bracket Align the Mounting Brackets Display Bottom Viewing Guide Center Center of Display Figure 4 4. Match the center of viewing guide with the center line you marked in step 1 (Figure 4). Figure 5 5. The mounting brackets are designed with a center of viewing guide on the side of them (Figure 5). Securing the Mounting Brackets The Griplates™ have M4, M5, M6 and M8 hole patterns to fit the hardware that your flat panel requires.
PWM-T210 Marking the Wall Viewing Port Center CENTER OF VIEWING HEIGHT DESIRED Mark the Wall 1. VIEWING PORTS CENTER OF VIEWING LINE Wall Structure MARKING THE LINE Figure 7 Align the center viewing port from the carton template to the wall. Match the center of viewing port to the center of viewing height desired (Figure 7). Figure 8 2. Mark a line on the bottom of the carton template (Figure 8). Marking the Bottom Mounting Points CAUTION: The lag bolts must be secured to the center of a stud.
PWM-T210 Securing the Lower Wall Plate Marked Wall Level Wall Plate Wall Plate Template Figure 11 1. 2. Figure 12 Level and secure the plate to the wall with the reference arrow facing up to the ceiling (Figure 11). Secure the plate using the provided lag bolts and washers. 3. 4. 5. When the bottom wall plate is properly installed to the wall. Lay the carton template on top of the wall plate.
PWM-T210 Mounting the Display WARNING: AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF THIS PRODUCT. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL. Top Bottom Figure 15 1. Raise the flat panel with the mounting brackets secured to the flat panel and insert the top and bottom hooks from each bracket to the rods from the wall plates (Figure 15). Lateral Shift M6 x 30 Lateral Shift Screw M6 x 30 Lateral Shift Screw Figure 16 2.
PWM-T210 Securing the Display M6 x 12mm Safety Knob M6 x 12mm Safety Knob Figure 17 1. Tilt the flat panel and secure the two (2) M6 x 12 mm safety knobs to each of the mounting brackets (Figure 17). NOTE: Page 10 To remove the display from the wall simply extend the display to its maximum tilt range, remove the two (2) M6 x 12mm Safety Knobs, push the flat panel back to it's flat position and loosen or remove the two (2) M6 x 30 lateral shift screws and lift the unit of the wall.
PWM-T210 Technical Specifications Dimensions shown in (mm)/inches. Warranty Limited Lifetime Warranty All Premier Mounts products carry a limited lifetime warranty from ship date against defects in materials and workmanship. Premier Mounts is not liable for improper installation that results in damage to mounts, adapters, display equipment or personal injury.
