Flat Panel Television User Manual

ManualsBrandsPioneer ManualsFlat Panel TVPDP-614MX External Control Manual PDP-614MX and PDP-424MV

External Control Manual

RS-232C Configuration

(for PDP-614MX and PDP-424MV)

Version 1.0

Dec 2005

Summary of content (60 pages)

PAGE 1
External Control Manual RS-232C Configuration (for PDP-614MX and PDP-424MV) Version 1.
PAGE 2
PDP-614MX External Control Manual Application These specifications are applicable to plasma monitors and communications control from external equipment. Connections Connections should be made as described below. plasma monitor External equipment e.g., Personal computer 1) Connector on the plasma monitor side: EXTERNAL CONTROL connector. Type of connector: D-Sub 9-pin male No.
PAGE 3
PDP-614MX External Control Manual 2) Connector on the external equipment side: Serial port (RS-232C) connector. See the specifications of the equipment that is to be connected for the type of connector and the pin assignment. 3) Wiring Use a crossed (reverse) cable. Wire the cable so that each pair of data lines cross between the two devices. These data line pairs are RXD (Receive data) and TXD (Transmit data), DTR (DTE side ready) and DSR (DCE side ready), and RTS (Ready to send) and CTS (Clear to send).
PAGE 4
PDP-614MX External Control Manual Communication Format 8bit 8bit 8bit 8bit 8bit 8bit 8bit 8bit Command 1 Unit ID 1 Unit ID 2 Command 2 Data length Data Check sum Command1 Command 1, along with command 2, is a number used to distinguish each command. When making it operate using ID, bit1 and bit0 are set up as follows.
PAGE 5
PDP-614MX External Control Manual the lower order 8 bits of one frame of sent or received data comprising the sum total of Command 1, Unit ID 1 and 2, Command 2, Data Length, and Data. Check Sum Example DFH 80H 60H Command1 Unit ID1 Unit ID2 47H 01H Command2 Data Length 01H 08H Data Check Sum Total 208H 2) Error Processing • When the communication interval is vacant for more than 4 ms, thereafter a received Command 1 will be recognized.
PAGE 6
PDP-614MX External Control Manual The control method of the set by Set ID When controlling two or more sets of plasma monitors, if the command using Set ID is used, it will become controllable individually. The example of the POWER ON command to the plasma monitor which set ID as "5" is shown below. It is not based on ID but is the POWER ON command to all sets. 9F 80 60 4E 00 CD In ID= "5", the value of ID-1=4 is set up.
PAGE 7
PDP-614MX External Control Manual Command Reference List 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 Power ON Power OFF Input Switch Change VOLUME Gain Data AUDIO Mute ON AUDIO Mute OFF CONTRAST Gain Data BRIGHT Gain Data SHARPNESS Gain Data Color Gain Data TINT Gain Data AV SELECTION Select COLOR TEMP SELECT RED Gain Data GREEN Gain Data BLUE Gain Data DNR MODE Set BASS Gain
PAGE 8
PDP-614MX External Control Manual 29 35 51 54 OSM Select INVESE Set TIMER SWITCH TIMER PROGRAM SETTING 55 PRESENT TIME SETTING 56 MULTI MODE Select 57 MULTI MODE Request 58 AUTO ID SET START 59 PLE LINK 60 VIDEO WALL SETTING 61 POWER DELAY ON (DIVIDER setting : 1/4/9) 62 POWER DELAY ON (DIVIDER setting : 16/25) 65 ORBITTER SET 67 OSM ANGLE 69*1 PICTURE Size 70 OPTION Select 71 REPEAT Timer DFH DFH DFH DFH 58H C7H 02H 30H 01H 03H 01H 08H DFH DFH 1FH 5FH DFH DFH DFH 31H 03H 3BH F0H F1H F3H F2H 03H 03H
PAGE 9
PDP-614MX External Control Manual 01. Power ON Function The external control equipment switches on the power of the plasma monitor. Transmission Data 9FH 80H 60H 4EH 00H CKS ACK The plasma monitor returns the following ACK when the power is switched on. 3FH 60H 80H 4EH 00H CKS NOTE: Do not set the Power ON or Power OFF command continuously. 02. Power OFF Function The external control equipment switches off the power of the plasma monitor.
PAGE 10
PDP-614MX External Control Manual 03. Input Switch Change Function The external control equipment switches the input of the plasma monitor. Transmission Data DFH 80H 60H 47H 01H DATA00 DATA00 : Input Select CKS 01H : Video1 02H : Video2 03H : Video3 05H : COMPNT1 06H : COMPNT2 07H : PC1DSUB 08H : PC2-BNC 0CH : PC3-DVI ACK The plasma monitor returns the following ACK when the input is switched.
PAGE 11
PDP-614MX External Control Manual 04. VOLUME Gain Data Function The external control equipment changes the VOLUME gain data of the plasma monitor. Transmission Data DFH 80H 60H 7FH 03H DATA00 DATA01 DATA02 DATA00: USER SOUND Gain Flag CKS 05H DATA01: VOLUME Gain Flag 01H DATA02: VOLUME Gain 00H: Step0 : 0AH: Step10 (Default) : 2AH: Step42 ACK 7FH 60H 80H 7FH 02H DATA00 DATA01 CKS DATA00: USER SOUND Gain Flag 05H DATA01: VOLUME Gain Flag 01H 05.
PAGE 12
PDP-614MX External Control Manual 07. CONTRAST Gain Data Function The external control equipment changes the CONTRAST gain data of the plasma c Transmission Data DFH 80H 60H 7FH 03H DATA00 DATA01 DATA02 DATA00 : USER PICTURE Gain Flag CKS 01H DATA01 : CONTRAST Gain Flag 07H DATA02 : CONTRAST Gain CCH : -52 : FFH : -01 00H : 0 01H : +01 : 14H : +20 ACK 7FH 60H 80H 7FH 02H DATA00 DATA01 CKS DATA00: USER PICTURE Gain Flag DATA01: CONTRAST Gain Flag 01H 07H 08.
PAGE 13
PDP-614MX External Control Manual 01H : +01 : 10H : +16 Only when a RGB signal is connected DATA02 : SHARPNESS Gain 01H : 1 02H : 2 03H : 3 04H : 4 ACK 7FH 60H 80H 7FH 02H DATA00 DATA01 CKS DATA00 : USER PICTURE Gain Flag DATA01 : SHARPNESS Gain Flag 06H 01H 13
PAGE 14
PDP-614MX External Control Manual 10. COLOR Gain Data Function The external control equipment changes the COLOR gain data of the plasma monitor. Transmission Data DFH 80H 60H 7FH 03H DATA00 DATA00 : USER PICTURE Gain Flag DATA01 DATA02 CKS 01H DATA01 : COLOR Gain Flag 04H DATA02 : COLOR Gain E0H : -32 : FFH : -01 00H : 0 01H : +01 : 20H : +32 * COLOR Gain is from -22 (EAH) to +22 (16H) only during video.
PAGE 15
PDP-614MX External Control Manual ACK 7FH 60H 80H 0AH 01H DATA00 CKS DATA00: 01H : STD 02H : MOVIE1 03H : MOVIE2 04H : Default 05H : Dynamic 13. COLOR TEMP SELECT Function The external control equipment changes the COLOR TEMP of the plasma monitor. Transmission Data DFH 80H 60H 00H 01H DATA00 DATA00 : CKS 00H: low 01H: middle 02H: high 03H: middle low ACK 7FH 60H 80H 00H 01H DATA00 DATA00 : CKS 00H: low 01H: middle 02H: high 03H: middle low 14.
PAGE 16
PDP-614MX External Control Manual 15. GREEN Gain Data Function The external control equipment changes the GREEN Gain Data of the plasma monitor.
PAGE 17
PDP-614MX External Control Manual 16. BLUE Gain Data Function The external control equipment changes the BLUE Gain Data of the plasma monitor.
PAGE 18
PDP-614MX External Control Manual 17. DNR MODE Set Function The external control equipment sets the NR (Noise Reduction) mode of the plasma monitor. Transmission Data DFH 80H 60H C0H 01H DATA00 CKS DATA00: 01H : OFF 02H : LOW 03H : MID 04H : HIGH ACK 7FH 60H 80H C0H 01H DATA00 CKS DATA00: 01H : OFF 02H : LOW 03H : MID 04H : HIGH 18. BASS Gain Data Function The external control equipment changes the BASS gain data of the plasma monitor.
PAGE 19
PDP-614MX External Control Manual 19. TREBLE Gain Data Function The external control equipment changes the TREBLE gain data of the plasma monitor. Transmission Data DFH 80H 60H 7FH 03H DATA00 DATA00 : USER PICTURE Gain Flag DATA01 DATA02 CKS 05H DATA01 : TREBLE Gain Flag 04H DATA02 : TREBLE Gain F3H : -13 : FFH : -01 00H : 0 01H : +01 : 0DH : +13 ACK 7FH 60H 80H 7FH 02H DATA00 DATA01 CKS DATA00: USER PICTURE Gain Flag 05H DATA01: TREBLE Gain Flag 04H 20.
PAGE 20
PDP-614MX External Control Manual 0AH : 2.35:1 ACK 7FH 60H 80H 51H 01H DATA00 CKS DATA00 02H : WIDE 03H : ZOOM 04H : STD 05H : FULL 06H : DOT BY DOT 08H : UNDERSCAN 09H : 14:9 0AH : 2.
PAGE 21
PDP-614MX External Control Manual 22. V.POSITION Gain Data Function The external control equipment changes the V. POSITION gain data of the plasma monitor. Transmission Data DFH 80H 60H 7FH 03H DATA00 DATA01 DATA02 DATA00 : USER PICTURE Gain Flag 03H DATA01 : V.POSITION Gain Flag 01H DATA02 : V.POSITION Gain C0H : -64 : FFH : -01 00H : 0 01H : +01 : 40H : +64 ACK 7FH 60H 80H 7FH 02H DATA00 DATA01 DATA00: USER PICTURE Gain Flag DATA01: V.
PAGE 22
PDP-614MX External Control Manual 23. H.POSITION Gain Data Function The external control equipment changes the H. POSITION gain data of the plasma monitor. Transmission Data DFH 80H 60H 7FH 03H DATA00 DATA01 DATA02 CKS DATA00 : USER PICTURE Gain Flag 03H DATA01 : H.POSITION Gain Flag 02H DATA02 : H.POSITION Gain 80H : -128 : FFH : -01 00H : 0 01H : +01 : 7FH : +127 ACK 7FH 60H 80H 7FH 02H DATA00 DATA00: USER PICTURE Gain Flag DATA01: H.POSITION Gain Flag DATA01 CKS 03H 02H 24. V.
PAGE 23
PDP-614MX External Control Manual 25. H.SIZE Gain Data Function The external control equipment changes the H.SIZE gain data of the plasma monitor. Transmission Data DFH 80H 60H 7FH 03H DATA00 DATA00 : USER PICTURE Gain Flag DATA01 DATA02 CKS 03H DATA01 : H.SIZE Gain Flag 08H DATA02 : H.SIZE Gain 00H : 0 : 40H : +64 ACK 7FH 60H 80H 7FH 02H DATA00 DATA00: USER PICTURE Gain Flag DATA01: H.SIZE Gain Flag DATA01 03H 08H CKS 26.
PAGE 24
PDP-614MX External Control Manual 27. PHASE Gain Data Function The external control equipment changes the PHASE gain data (Phase) of the plasma monitor. Transmission Data DFH 80H 60H 7FH 03H DATA00 DATA00 : USER PICTURE Gain Flag DATA01 DATA02 CKS 03H DATA01 : PHASE Gain Flag 03H DATA02 : PHASE Gain 00H : 0 : 40H : +64 : ACK 7FH 60H 80H 7FH 02H DATA00 DATA00: USER PICTURE Gain Flag DATA01: PHASE Gain Flag DATA01 03H 03H CKS 28.
PAGE 25
PDP-614MX External Control Manual 29. OSM ADJ. POSITION Data Function The external control equipment sets the position of the OSM menu of the plasma monitor. Transmission Data DFH 80H 60H 1AH 02H DATA00 DATA00 : OSM ADJ. Gain Flag DATA01 DATA01 CKS 02H 01H : 1(TOP LEFT) 02H : 2(TOP CENTER) 03H : 3(TOP RIGHT) 04H : 4(BOTTOM LEFT) 05H : 5(BOTTOM CENTER) 06H : 6(BOTTOM RIGHT) ACK 7FH 60H 80H 1AH 01H DATA00 CKS DATA00 : OSM ADJ. Gain Flag 02H 30.
PAGE 26
PDP-614MX External Control Manual Function The external control equipment switches on or off the PURECINEMA of the plasma monitor.
PAGE 27
PDP-614MX External Control Manual 33. LONG LIFE Set Function The external control equipment sets the PLE, ORBITER, and INVERSE (inverse of image brightness) or WHITE of the plasma monitor.
PAGE 28
PDP-614MX External Control Manual 34. SCREEN WIPER Set Function The external control equipment sets the SCREEN WIPER of the plasma monitor. Transmission Data DFH 80H 60H C8H 04H DATA00 to DATA03 CKS DATA00 : SCREEN WIPER 00H : No operation 01H : ON 02H : OFF DATA01 : 00H : fixed DATA02 : FFH: fixed DATA03 : 01H : fixed ACK 3FH 60H 80H C8H 00H CKS 35. ALL RESET Function The external control equipment resets the user adjustment of the plasma monitor.
PAGE 29
PDP-614MX External Control Manual 36. Audio Select Set Function The external control equipment sets combinations of audio and video inputs for the plasma monitor. Transmission Data DFH 80H 60H 70H 02H DATA00 DATA00 : AUDIO INPUT DATA01 CKS 01H : AUDIO1 02H : AUDIO2 03H : AUDIO3 DATA01 : VISUAL INPUT 01H : VIDEO1 02H : VIDEO2 03H : VIDEO3 05H : COMPNT1 06H : COMPNT2 07H : PC1DSUB 08H : PC2-BNC 0CH : PC3-DVI ACK The plasma monitor returns the following ACK when the input is switched.
PAGE 30
PDP-614MX External Control Manual 37. BNC INPUT Function The external control equipment sets the BNC SELECT of the plasma monitor. Transmission Data DFH 80H 60H 8CH 01H DATA00 CKS DATA00 : BNC SELECT 01H : RGB 02H : Component ACK The plasma monitor returns the following ACK when setting the BNC SELECT: 7FH 60H 80H 8CH 01H DATA00 CKS DATA00 : BNC SELECT 01H : RGB 02H : Component 38. RGB Select Function The external control equipment sets the RGB SELECT of the plasma monitor.
PAGE 31
PDP-614MX External Control Manual 40. LANGUAGE Select Function The external control equipment sets the LANGUAGE SELECT of the plasma monitor. Transmission Data DFH 80H 60H 5BH 01H DATA00 CKS DATA00: 01H : ENGLISH 02H : GERMAN 03H : FRENCH 04H : SPANISH 05H : ITALIAN 06H : SWEDISH 07H : JAPANESE 0AH : CHINESE ACK 7FH 60H 80H 5BH 01H DATA00 CKS DATA00: 01H : ENGLISH 02H : GERMAN 03H : FRENCH 04H : SPANISH 05H : ITALIAN 06H : SWEDISH 07H : JAPANESE 0AH : CHINESE 41.
PAGE 32
PDP-614MX External Control Manual 42. FREQUENCY Request(SIGNAL INFORMATION) Function The external control equipment inquires the Horizontal frequency, Vertical frequency, Horizontal sync polarity, Vertical sync polarity, Mode, and Resolution of the plasma monitor.
PAGE 33
PDP-614MX External Control Manual MODE DATA06 00H 01H to 80H 81H 82H 83H 84H 85H 86H 87H 88H 89H A0H A1H A2H A3H A4H A5H A6H － : No signal : RGB signal Identification number of PC mode : Video signal 3.58NTSC : 4.
PAGE 34
PDP-614MX External Control Manual 43. Input MODE Request Function The display returns the current input information by the external control equipment’ s request. Transmission Data 1FH 80H 60H 41H 00H CKS ACK 7FH 60H 80H 41H 01H DATA00 DATA00 : Input Select CKS 01H : Video 02H : Video2 03H : Video3 04H : COMPNT1 05H : PC1DSUB 06H : PC2-BNC 0CH : COMPNT2 0EH : PC3-DVI 44. VIDEO ADJ. Request Function The display returns the video adjustments information by the external control equipment’s request.
PAGE 35
PDP-614MX External Control Manual DATA04: TINT Gain * TINT Gain is from -22 (EAH) to +22 (16H) only during video.
PAGE 36
PDP-614MX External Control Manual 01H : +01 : 1EH : +30 DATA0B: COLOR TEMP SELECT 00H: low 01H: middle 02H: high 03H: middle low 45. Audio Select Request Function The external control equipment inquires the current combinations of audio and video inputs for the plasma monitor.
PAGE 37
PDP-614MX External Control Manual 46. Failure Mode Request Function The external control equipment inquires the detection of failures of the plasma monitor.
PAGE 38
PDP-614MX External Control Manual 47. MODEL NAME Request Function The external control equipment inquires the product code of the plasma monitor.
PAGE 39
PDP-614MX External Control Manual 48.LOW TONE Function The external control equipment sets the dithering processing or error diffusion processing of the plasma monitor.
PAGE 40
PDP-614MX External Control Manual 49. C.DETAIL ADJ Function External control equipment can adjust RGB each color which a plasma monitor wants to emphasize.
PAGE 41
PDP-614MX External Control Manual ACK 7FH 60H 80H 13H 01H DATA00 CKS DATA00: GAMMA FLAG 01H : Gamma change 41
PAGE 42
PDP-614MX External Control Manual 51.Running Sense Function External control apparatus grasps the power supply state of a plasma monitor. A plasma monitor is made to recognize connection of PC CONTROL.
PAGE 43
PDP-614MX External Control Manual 52. OSM OBITER Function In order to decrease printing of a screen by OSM display, whenever it displays OSM, shift operation of the OSM is carried out. Transmission Data DFH 80H 60H 5FH 01H DATA00 DATA00 CKS 01H : OBITER ON 02H : OBITER OFF ACK 7FH 60H 80H 5FH 01H DATA00 DATA00 CKS 01H : OBITER ON 02H : OBITER OFF 53. Input Skip Function In a monitor's key "an input change", when there is no signal, it flies and shifts to the following channel.
PAGE 44
PDP-614MX External Control Manual 54. SERIAL No. Request Function External control apparatus read the serial number of the set recorded by EEPROM of a plasma display. Transmission Data 1FH 80H 60H 15H 00H CKS ACK 7FH 60H 80H 15H 0CH DATA00 to DATA11 CKS Even DATA00-DATA11 is set up as follows. Setting value 00H-09H : 0-9 96H 10H-29H : Blank : A-Z of Alphabet 55.S1/S2 SELECT Function External control apparatus sets up the S1/S2 detection of a plasma monitor.
PAGE 45
PDP-614MX External Control Manual 56.SOFT FOCUS Function External control apparatus sets up the Soft Focus of a plasma monitor. Transmission Data DFH 80H 60H 65H 01H DATA00 01H : OFF 02H : LEVEL1 03H : LEVEL2 04H : LEVEL3 05H : LEVEL4 ACK 7FH 60H 80H 65H 01H DATA00 01H : OFF 02H : LEVEL1 03H : LEVEL2 04H : LEVEL3 05H : LEVEL4 DATA00 CKS DATA00 CKS 57.PLUG and PLAY Function External control apparatus sets up the Plug and Play of a plasma monitor.
PAGE 46
PDP-614MX External Control Manual 58.BLACK LEVEL SELECT Function External control apparatus sets up the black level (digital signal level) of a plasma monitor. Transmission Data DFH 80H 60H DATA00 8FH 01H DATA00 CKS DATA00 CKS 01H : LOW 02H : HIGH ACK 7FH 60H DATA00 80H 8FH 01H 01H : LOW 02H : HIGH 59.OSM CONTRAST SELECT Function External control apparatus selects the OSM contrast function of a plasma monitor.
PAGE 47
PDP-614MX External Control Manual Remote control operation Personal computer control operation Yes Yes Yes No No No Yes No 61. INVERSE Set 2001.7.10 The external control equipment sets the INVERSE (inverse of image brightness) and the WHITE of the plasma INVERSE monitor.
PAGE 48
PDP-614MX External Control Manual 62. TIMER SWITCH Function The external control equipment sets the timer reservation of the plasma monitor. Transmission Data DFH 80H 60H 02H 01H DATA00 CKS DATA00: 00H : Reservation OFF 01H : Reservation ON ACK 7FH 60H 80H 02H 01H DATA00 CKS DATA00: 00H : Reservation OFF 01H : Reservation ON 63. TIMER PROGRAM SETTING Function External control apparatus sets up the timer program of a plasma monitor.
PAGE 49
PDP-614MX External Control Manual DATA06 INPUT 01H : Video1 02H : Video2 03H : Video3 04H 05H : COMPNT1 : COMPNT2 06H : PC1DSUB 07H : PC2-BNC 08H : PC3-DVI FFH : - (with No Setup) DATA07 MODE 01H : OBIT 02H : INV 03H : WT 04H : WIPER FFH : - (with No Setup) ACK 7FH 60H 80H 30H 00H CKS 64. PRESENT TIME SETTING Function External control apparatus sets up the present time of a plasma monitor.
PAGE 50
PDP-614MX External Control Manual DATA01 (POSITION OF DIVIDE) 01H : Upper left selected (4 screens) 02H : Upper right selected (4 screens) 03H : Lower right selected (4 screens) 04H : Lower left selected (4 screens) 07H : Top left selected (9 screens) 08H : Top middle selected (9 screens) 09H : Top right selected (9 screens) 0AH : Middle left selected (9 screens) 0BH : Middle centerselected (9 screens) 0CH : Middle rightselected (9 screens) 0DH : Bottom leftselected (9 screens) 0EH : Bottom middle selected
PAGE 51
PDP-614MX External Control Manual 05H : Multi mode 16 screens 06H : Multi mode 25 screens DATA01 (POSITION OF DIVIDE) 01H : Upper left selected (4 screens) 02H : Upper right selected (4 screens) 03H : Lower right selected (4 screens) 04H : Lower left selected (4 screens) 07H : Top left selected (9 screens) 08H : Top middle selected (9 screens) 09H : Top right selected (9 screens) 0AH : Middle left selected (9 screens) 0BH : Middle centerselected (9 screens) 0CH : Middle rightselected (9 screens) 0DH : Botto
PAGE 52
PDP-614MX External Control Manual Transmission Data 1FH 80H 60H 3BH 00H CKS ACK 7FH 80H 60H 3BH 02H DATA00 DATA01 DATA02 CKS DATA00 (SCREEN DIVIDER SETTING) 01H : Single mode 02H : Multi mode 1 screens 03H : Multi mode 4 screens 04H : Multi mode 9 screens 05H : Multi mode 16 screens 06H : Multi mode 25 screens DATA01 (POSITION OF DIVIDE) 01H : Upper left selected (4 screens) 02H : Upper right selected (4 screens) 03H : Lower right selected (4 screens) 04H : Lower left selected (4 screens) 07H : Top left sel
PAGE 53
PDP-614MX External Control Manual DATA02 (DISP MODE) 00H : SPLIT 01H : BRANKING 53
PAGE 54
PDP-614MX External Control Manual 67. AUTO ID SET START Function External control apparatus sets up ID automatically to two or more plasma monitors. Transmission Data 5FH 80H 60H F0H 01H DATA00 CKS DATA00 00H~FFH: ID of a master*1 is set up. *: When you use it by the multi-system, please remove the link input of a master*1. *1: “Master” means the 1st set of PDP at the time of cable connection at the time of AUTO ID execution. 68.
PAGE 55
PDP-614MX External Control Manual 55
PAGE 56
PDP-614MX External Control Manual 70. POWER DELAY ON(at 4 or 9 multiscreen) Function External control apparatus attaches a time lag to two or more plasma monitors, and turns on a power supply. Transmission Data DFH 80H 60H F2H 01H DATA00 CKS DATA00: 00H-FFH: Delay time (second) *:Turn on the AUTO ID and set the DIVIDER(at 4 or 9), before this operation *: This command is premised on two or more plasma monitor system composition being multi-systems.
PAGE 57
PDP-614MX External Control Manual 72. ORBITER SET Function A picture shift function is set up.
PAGE 58
PDP-614MX External Control Manual Transmission Data DFH 80H 60H 2AH 01H DATA00 CKS DATA00 01H : ON 02H : OFF ACK 7FH 60H 80H 2AH 01H DATA00 CKS DATA00 01H : ON 02H : OFF 75. OPTION Select Function Power-on mode, a control lock, and IR remote are set up.
PAGE 59
PDP-614MX External Control Manual 0CH : PC3-DVI DATA03 WORK TIME 01 H-FFH:1 - 255 minutes (1 minute - 4 hours and 15 minutes) DATA04 PROGRAM 1 01H :DIVIDER 1 02H :DIVIDER 4 03H :DIVIDER 9 DATA05 SOURCE 01H :Video1 02H :Video2 03H :Video3 05H : COMPNT1 06H : COMPNT2 07H : PC1DSUB 08H : PC2-BNC 0CH : PC3-DVI DATA06 WORK TIME 01 H-FFH:1 - 255 minutes (1 minute - 4 hours and 15 minutes) ACK 7FH 60H 80H 64H 00H CKS *:Turn on the AUTO ID, before this operation 59
PAGE 60
External Control Manual RS-232C Configuration (for PDP-614MX and PDP-424MV) Pioneer Electronics (USA) Inc. Industrial Solutions Business Group 2265 East 220th Street Long Beach, CA 90810 www.pioneerelectronics.com www.pioneerindustrialav.