Operating Instructions Network Audio Player N-70A/N-50A USB Audio Driver software (for Windows)
About these Operating Instructions When a USB cable is used to connect the unit’s USB DAC port to a computer, audio files located on the computer can be played. In order to use this function, a dedicated driver (software program) must be installed in the computer. These Operating Instructions contain important information necessary for playing files on the computer, including instructions about how to install the driver and how to perform troubleshooting in event of problems.
Use a proper USB cable to connect a computer to a device equipped with USB DAC connector, then turn on the power. 6 Click on [Next]. 7 Click on [Install]. For more information regarding connections, check the Operating Instructions for this device. USB A–type AL OUT 2 COAXIAL OPTICAL DC OUTPUT CONTROL For OUT WIRELESS LAN 5V 0.6A MAX) AC IN DIGITAL IN 1 COAXIAL DIGITAL IN iPod/iPhone 5V 1A USB DAC B–type * The illustration may appear differently, depending on the model used.
8 Click on [Finish]. 5 Click [Next] and proceed to the uninstall execution screen. 6 Click [Next] to execute the uninstall process. 7 Click on [Finish], then reboot your computer. . The driver installation is completed. 9 Reboot your computer to finalize installation of the driver. Procedure finished. To uninstall the driver If you wish to uninstall (delete) the driver at any time after installing it, perform the following operation on your computer.
Troubleshooting (Windows XP) 4 Click on [Sound, video and game controllers] and confirm that [Pioneer N-70A N-50A USB Audio] is listed. When using Windows Vista, see page 7 ; for Windows 7, see page 11 ; for Windows 8 or Windows 8.1, see page 15. 1. No sound Do not boot your computer’s music player program if the power is turned off to the device with the USB DAC port, or if the USB DAC port has not been selected as the input source.
7 Click on the [Audio] tab, then confirm that [Pioneer N-70A N-50A USB Audio] is listed as the [Default device] for [Sound playback]. If another device has been selected, open the drop-down menu and select [Pioneer N-70A N-50A USB Audio], then click on [Apply] to change the selection. 8 9 2. To disable the operating system’s sound scheme Under default OS settings, computer events may be accompanied by audio signals and beeps that are audible through the speakers attached to the device.
Troubleshooting (Windows Vista) 3 Click on [Sound, video and game controllers] and confirm that [Pioneer N-70A N-50A USB Audio] is listed. When using Windows XP, see page 5 ; for Windows 7, see page 11 ; for Windows 8 or Windows 8.1, see page 15. 1. No sound Do not boot your computer’s music player program if the power is turned off to the device with the USB DAC port, or if the USB DAC port has not been selected as the input source.
5 Click on [Start] [Control Panel] [Hardware and Sound] [Sound]. 6 Under the [Playback] tab, confirm that for [Speakers], [Pioneer N-70A N-50A USB Audio] is checked as the default device. 8 Under the [Levels] tab, set the [Speakers] level to maximum. If the Speaker Mute indicator (at the left side of the Balance button) is lighted, click it to turn it off. If another device has been selected, select [Pioneer N-70A N-50A USB Audio], and click to [Set Default].
2. To disable the operating system’s sound scheme Under default OS settings, computer events may be accompanied by audio signals and beeps that are audible through the speakers attached to the device. In the event you do not wish to hear such non-music signals, follow the instructions listed below: 1 Click [Start] [Control Panel] [Hardware and Sound] [Sound]. 2 Click on the [Sounds] tab, and for the [Sound scheme], select [No Sounds], then click on [Apply]. 3.
3 Under the [Advanced] tab, select for [Default Format] the desired output sampling rate, then click on [Apply]. Procedure finished.
Troubleshooting (Windows 7) 4 Click on [Universal Serial Bus controllers], and confirm that [USB Composite Device] is listed. 5 Click on [Start] [Control Panel] [Hardware and Sound] [Sound]. When using Windows XP, see page 5 ; for Windows Vista, see page 7 ; for Windows 8 or Windows 8.1, see page 15. 1. No sound Do not boot your computer’s music player program if the power is turned off to the device with the USB DAC port, or if the USB DAC port has not been selected as the input source.
6 Under the [Playback] tab, confirm that for [Speakers], [Pioneer N-70A N-50A USB Audio] is checked as the [Default Device]. 8 Under the [Levels] tab, set the [Speakers] level to maximum. If the Speaker Mute indicator (at the left side of the Balance button) is lighted, click it to turn it off. If another device has been selected, select [Pioneer N-70A N-50A USB Audio], and click on [Set Default]. 9 7 Double click on [Speakers] ([Pioneer N-70A N-50A USB Audio]), and display its Properties.
2. To disable the operating system’s sound scheme Under default OS settings, computer events may be accompanied by audio signals and beeps that are audible through the speakers attached to the device. In the event you do not wish to hear such non-music signals, follow the instructions listed below: 1 Click [Start] [Control Panel] [Hardware and Sound] [Sound]. 2 Click on the [Sounds] tab, and for the [Sound scheme], select [No Sounds], then click on [Apply]. 3.
3 Under the [Advanced] tab, select for [Default Format] the desired output sampling rate, then click on [Apply]. Procedure finished.
Troubleshooting (Windows 8/8.1) 3 Click on [Universal Serial Bus controllers], and confirm that [USB Composite Device] is listed. 4 Simultaneously press the [Windows] key and [X] key; select [Control Panel], then click on [Hardware and sound] [Manage audio devices]. When using Windows XP, see page 5 ; for Windows Vista, see page 7 ; for Windows 7, see page 11. 1.
5 Under the [Playback] tab, confirm that for [Speakers], [Pioneer N-70A N-50A USB Audio] is checked as the [Default Device]. 7 Under the [Levels] tab, set the [Speakers] level to maximum. If the Speaker Mute indicator (at the left side of the Balance button) is lighted, click it to turn it off. If another device has been selected, select [Pioneer N-70A N-50A USB Audio], and click on [Set Default]. 8 6 Double click on [Speakers] ([Pioneer N-70A N-50A USB Audio]), and display its Properties.
2. To disable the operating system’s sound scheme Under default OS settings, computer events may be accompanied by audio signals and beeps that are audible through the speakers attached to the device. In the event you do not wish to hear such non-music signals, follow the instructions listed below: 1 Simultaneously press the [Windows] key and [X] key; select [Control Panel], then click on [Hardware and sound] [Manage audio devices].
3 Under the [Advanced] tab, select for [Default Format] the desired output sampling rate, then click on [Apply]. Procedure finished.
© 2014 PIONEER HOME ELECTRONICS CORPORATION. All rights reserved. PIONEER HOME ELECTRONICS CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan http://pioneer.jp PIONEER ELECTRONICS (USA) INC. P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404 http://www.pioneerelectronics.com/PUSA PIONEER ELECTRONICS OF CANADA, INC. 340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada TEL: 1-877-283-5901, 905-479-4411 http://www.pioneerelectronics.
