Owner's Manual
Table Of Contents
•
Install
thls
unit
away
from
hot
places
such
as
near
the
heater
outlet.
•
Optimum
performance
is
obtained
when
the
unit
is
installed
at
an
angle
of
less
than
6Cr.
•
When
installing,
to
ensure
proper
heat
dlspersal
when
using
this
unit,
make
sure
you
leave
ample
space
behind
the
rear
panel
and
wrap
any
loose
cables
so
they
are
not
blocking
the
vents.
Leave
ample
space
DIN
mount
installation
1 Insert
the
supplied mounting sleeve into
the
dashboard
.
2 Secure
the
mounting sleeve
by
using a
screwdriver
to
bend
the
metal
tabs
(90°)
Into place.
~
,1
Dashboard
@
Mounting
sleeve
•
Make
sure
that
the
unit
is
installed
securely
In
place.
An
unstable
installation
may
cause
skipping
or other
malfunctions.
When
not
using
the
supplied
mounting
sleeve
1
line
up
the
holes
on
the
mounting
bracket with
the
holes
on
the
sides
of
the
unit
to
attach
the
bracket.
2 Screw
in
one
screw
on
each
side
to
hold
the
unit
In
place.
(D
Tapping
screw
(5
mm
x 9
mm,
not
supplied
with
product)
@ Mounting
bracket
@
Dashboard
or
console
Removing
the
unit
(installed
with
the
supplied
mounting
sleeve)
1 Remove
the
trim ring.
(!)
Trim
ring
@ Notched
tab
•
Releasing
the
front
panel
allows
easier
access
to
the
trim
ring.
•
When
reattaching
the
trim
ring,
point
the
side
with
the
notched
tab
down.
2 Insert
the
supplied extraction keys into
both
sides
of
the
unit
until
they
click into
place.
3 Pull
the
unit
out
of
the
dashboard.
To secure
the
front
panel
The
front
panel
can
be
secured
with
the
supplied
screw.
~ ©
Screw
AwARNING
---------------------,
Do
not
attempt
to
operate
the
application
while
driving. Make sure
to
stop
your
boat
in
a safe location before
attempting
to
use
the
controls
on
the
application.
1 Enter
the
SYSTEM
menu
(refer
to
"About
the
main menu").
2 Turn
the
M.C.
dial
to
select
[APP
CONTROL),
then
press
to
confirm.
3 Turn
the
M.C.
dial
to
select
one
of
the
below.
Select
[WIRED)
for
the
USB
connection.
• Select
[BLUETOOTH)
for
the
Bluetooth connection.
4 Turn
the
M.C.
dial
to
select [AUTO
APP
CONN),
then
press
to
confirm
.
5 Turn
the
M.C.
dial
to
select [ON],
then
press
to
confirm.
6 Connect this
unit
with
the
mobile
device via
USB
or
Bluetooth.
Pioneer Smart Sync
on
the
iPhone/Android device starts
automatically.
NOTE
Regardless
of
whether
the
[AUTO
APP
CONN]
setting
is
set
to
[ON]
or
[OFF],
you
can
also
perform
the
following
to
start
Pioneer Smart Sync.
- For devices
other
than
the
USS-connected Android device, press
SRC/OFF
to
select any
source
and
press and hold
the
M.C. dial.
- For iPhone, launch Pioneer Smart Sync
on
the
mobile device.
Listening
to
Pandora
'"
'
(Not available
when
[USS
MTP]
is
set
to
[ON]
in
the
SYSTEM
settings.)
Update
the
firmware
of
the
Pandora application
to
the
latest version before use.
Before you start,
connect
this unit with
the
mobile device via
USS
(iPhone only)
or
Bluetooth.
1 Enter
the
SYSTEM
menu
(refer
to
"About
the
main
menu").
2 Turn
the
M.C.
dial
to
select
[APP
CONTROL),
then
press
to
confirm.
The
microphone
should
be
placed
directly
In
front
of
the
driver
at
a
suitable
distance
to
pick
up
their
voice
clearly.
ACAUTION
•
Carefully
select
the
mounting
location
to
avoid
Internal
damage
by
water
entering
the
microphone.
Areas
subject
to
water
splashes
should
be
avoided.
•
It
is
extremely
dangerous
to
allow
the
microphone
lead
to
become
wound
around
the
steering
column
or
shift
lever.
Be
sure
to
install
the
microphone
In
such
a
way
that It
will
not
obstruct
driving.
It
is
recommended
to
use
the
clamps
(sold
separately)
to
arrange
the
lead.
1
Slide
the microphone
base
to detach
It
from the microphone
clip
.
CD
Microphone
@
Microphone
clip
'J,
Microphone
base
2 Install
the
microphone
as
follows.
1
Double-sided
tape
I Clamp (sold separately)
3 Turn
the
M.C.
dial
to
select one
of
the
below.
Select [WIRED]
for
the
USB
connection.
• Select
[BLUETOOTHJ
for
the
Bluetooth connection.
4
Press
SRC/OFF
to
select [PANDORA].
5 Launch
the
Pandora application
on
the
mobile
device and start
playback.
Listening
to
Spotify®
(Not available
when
[USS
MTP]
is
set
to
[ON]
in
the
SYSTEM
settings.)
Update
the
firmware
of
the
Spotify application
to
the
latest version before use.
Before you start,
connect
this unit with
the
mobile device via
USS
(iPhone only)
or
Bluetooth.
1 Enter
the
SYSTEM
menu
(refer
to
"About
the
main menu").
2 Turn
the
M.C.
dial
to
select
[APP
CONTROL],
then
press
to
confirm.
3 Turn
the
M.C.
dial
to
select
one
of
the
below
.
Select
[WIRED)
for
the
USB
connection.
• Select
[BLUETOOTHJ
for
the
Bluetooth connection.
4
Press
SRC/OFF
to
select
[SPOTIFY).
5 Launch
the
Spotify application
on
the
mobile
device and start
playback.