SDS

ManualsBrandsPioneer ManualsPaintTextured White Fiberglass Reinforced Plastic (FRP) Wall Panel - 4 x 8

SAFETY DATA SHEET

SECTION I - PRODUCT AND COMPANY IDENTIFICATION

Product:

Fiberglass Reinforced Plastic (FRP)

Recommended Use:

Used for building applications

Manufacturer Information:

Panolam Industries International Inc.

325 DeSoto Ave.

Morr

istown, TN 37813

(423) 587-1842

Emergency Contact (24 hours):

CHEMTREC 1-800-424-9300

SECTION II – HAZARD IDENTIFICATION

SECTION III – COMPOSITION INFORMATION

Panolam FRP panels are solid sheets which are composed of fiberglass, inorganic fillers, pigments and other

additives that are embedded in a cured unsaturated polyester resin. These panels are considered as “articles”

as defined in the OSHA Hazard Communication standard in 29 CFR 1910.1200 (c) and are not considered

hazardous under normal use.

SECTION IV – FIRST AID MEASURES

Inhalation: Material does not vaporize. If exposed to dust remove to fresh air. Get medical

attention if irritation persists, or if severe coughing or breathing difficulty occurs.

Eye Contact: Flush eyes with large amounts of water. Remove to fresh air. Get medical attention

if irritation persists.

GHS Classification:

Not applicable – Non-hazardous

GHS Signal Word

Not applicable – Non-hazardous

GHS Pictograms

Not applicable – Non-hazardous

Hazard Statement

Not applicable – Non-hazardous

Precautionary Statement

May form combustible dust concentrations in air if small particles are

generated during further processing, handling or by other means.

Summary of content (6 pages)

PAGE 1
SAFETY DATA SHEET SECTION I - PRODUCT AND COMPANY IDENTIFICATION Product: Fiberglass Reinforced Plastic (FRP) Recommended Use: Manufacturer Information: Used for building applications Panolam Industries International Inc. 325 DeSoto Ave.
PAGE 2
Page 2 of 6 Skin Contact: Wash affected areas with soap and water. Get medical attention if rash or irritation persists or dermatitis occurs. Ingestion: Rinse mouth with water. Get medical attention if irritation persists. Recommendations for Immediate Medical Care/Special Treatment: None known. SECTION V – FIREFIGHTING MEASURES Extinguishing media: Special Hazards: Water Fog, Carbon Dioxide, Dry Chemical, Chemical Foam.
PAGE 3
Page 3 of 6 Eye protection: Respiratory protection: Body protection: Foot protection: General Hygiene/Safety Measures: Safety glasses or goggles are recommended when machining this material. None should be required during normal operations. When dust is generated a NIOSH approved respirator may be used when exposure levels to dust are thought to be above regulated values. No special precautions are required. If exposed to dust wash with soap and water to remove any material from the skin. Safety shoes.
PAGE 4
Page 4 of 6 SECTION XI- TOXICOLOGICAL PROPERTIES Route of Entry: Skin contact [X] Inhalation [X] Skin absorption [ ] Ingestion [X] Eye contact [X] EFFECTS OF ACUTE EXPOSURE: Inhalation: Eye Contact: Skin Contact: Skin Absorption: Ingestion: Not considered a problem under normal use. Dust generated during machining can cause short-term irritation of the mouth, nose, throat or upper respiratory tract. Not considered a problem under normal use.
PAGE 5
Page 5 of 6 SECTION XIII – DISPOSAL CONSIDERATIONS Waste disposal method: Container disposal This product is not considered a hazardous waste under EPA Hazardous Waste Regulations 40 CFR Part 261, however, State and local requirements for waste disposal may differ and should be reviewed. Can be landfilled or incinerated in accordance with local, provincial, state, federal regulations. Do not discharge substance/product into sewer system.
PAGE 6
Page 6 of 6 SARA 313: This product does not contain chemical(s) in concentrations which should require reporting under SARA 313. SECTION XVI – OTHER INFORMATION Revision Date: 5/7/15 DISCLAIMER: The information and data herein are believed to be accurate and have been compiled from sources believed to be reliable. It is offered for your consideration, investigation and verification.