Stereo Receiver User Manual

ManualsBrandsPioneer ManualsTV ReceiverElite SC-35

Operating Instructions

audio/video multi-channel receiver

SC-37

SC-35

SC-37_35_UXJCB.book 1 ページ２０１０年３月９日　火曜日　午前９時３２分

Summary of content (148 pages)

PAGE 1
SC-37_35_UXJCB.
PAGE 2
SC-37_35_UXJCB.book 2 ページ２０１０年３月９日火曜日午前９時３２分 IMPORTANT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
PAGE 3
SC-37_35_UXJCB.book 3 ページ２０１０年３月９日火曜日午前９時３２分 FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 4
SC-37_35_UXJCB.book 4 ページ２０１０年３月９日火曜日午前９時３２分 This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period. K041_A1_En SC-37 only This device complies with Part 15 of the FCC Rules.
PAGE 5
SC-37_35_UXJCB.book 5 ページ２０１０年３月９日火曜日午前９時３２分 Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference. Contents 01 Before you start Our philosophy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 6
SC-37_35_UXJCB.book 6 ページ２０１０年３月９日火曜日午前９時３２分 Listening to XM Radio. . . . . . . . . . . . . . . . . . . . . . . . . 53 Using XM HD Surround . . . . . . . . . . . . . . . . . . . . . . 54 Saving channel presets . . . . . . . . . . . . . . . . . . . . . . 54 Using the XM Menu . . . . . . . . . . . . . . . . . . . . . . . . . 54 Listening to SIRIUS Radio . . . . . . . . . . . . . . . . . . . . . 54 Saving channel presets . . . . . . . . . . . . . . . . . . . . . . 55 Using the SIRIUS Menu . . . . . . .
PAGE 7
SC-37_35_UXJCB.book 7 ページ２０１０年３月９日火曜日午前９時３２分 10 Controlling the rest of your system (In case of SC-35) 12 The System Setup and Other Setup menus About the Remote Setup menu . . . . . . . . . . . . . . . . . 96 Operating multiple receivers . . . . . . . . . . . . . . . . . . . 96 Setting the remote to control other components . . . . 97 Selecting preset codes directly . . . . . . . . . . . . . . . . . 97 Programming signals from other remote controls . . .
PAGE 8
SC-37_35_UXJCB.book 8 ページ２０１０年３月９日火曜日午前９時３２分 Flow of settings on the receiver The unit is a full-fledged AV receiver equipped with an abundance of functions and terminals. It can be used easily after following the procedure below to make the connections and settings.
PAGE 9
SC-37_35_UXJCB.book 9 ページ２０１０年３月９日火曜日午前９時３２分 Before you start 01 Chapter 1: Before you start Our philosophy Pioneer is dedicated to making your home theater listening experience as close as possible to the vision of the moviemakers and mastering engineer when they created the original soundtrack.
PAGE 10
SC-37_35_UXJCB.book 01 10 ページ２０１０年３月９日火曜日午前９時３２分 Before you start Checking what’s in the box Loading the batteries Please check that you’ve received the following supplied accessories: In case of SC-37 In case of SC-37 • Setup microphone (cable: 5 m (16.4 ft.
PAGE 11
SC-37_35_UXJCB.book 11 ページ２０１０年３月９日火曜日午前９時３２分 Before you start Operating range of remote control unit The remote control may not work properly if: • There are obstacles between the remote control and the receiver’s remote sensor. • Direct sunlight or fluorescent light is shining onto the remote sensor. • The receiver is located near a device that is emitting infrared rays. • The receiver is operated simultaneously with another infrared remote control unit.
PAGE 12
SC-37_35_UXJCB.book 02 12 ページ２０１０年３月９日火曜日午前９時３２分 Controls and displays Chapter 2: Controls and displays Remote control (In case of SC-37) This section explains how to operate the remote control for the receiver. RECEIVER MAIN BD 4 SOURCE ZONE2 3 MULTI OPERATION BDR DVR DVD CD USB iPod TUNER HDMI 3 MULTI OPERATION Use this button to perform multi operations (page 99).
PAGE 13
SC-37_35_UXJCB.book 13 ページ２０１０年３月９日火曜日午前９時３２分 Controls and displays 10 Receiver Control buttons Set the remote control operation selector switch to RECEIVER first to access: 02 13 VOL +/– Use to set the listening volume. STATUS – Press to check selected receiver settings (page 81). 14 MUTE Mutes the sound or restores the sound if it has been muted (adjusting the volume also restores the sound). PHASE CTRL – Press to switch on/off Phase Control or Full Band Phase Control (page 63).
PAGE 14
02he_Controls_displays.fm 14 ページ２０１０年３月９日火曜日午前１０時２３分 Controls and displays 02 MAIN (Gray box with black letters): Two-way communications are established and the receiver’s power is off. RF adapter Front (White letters only): Two-way communications are not working well. In this case, the area indicating the receiver’s status (12) is not displayed. 1 MAIN 2 2 Remote control code sending indicator This appears when signals are sent from the remote control.
PAGE 15
SC-37_35_UXJCB.book 15 ページ２０１０年３月９日火曜日午前９時３２分 Controls and displays 02 Remote control (In case of SC-35) This section explains how to operate the remote control for the receiver. 10 RECEIVER MULTI OPERATION 1 2 DVD TV CD HDMI Use INPUT SELECT to select the input function (page 47). NET RADIO ADAPTER 4 TV CTRL Set the preset code of your TV’s manufacturer when controlling the TV (page 97).
PAGE 16
SC-37_35_UXJCB.book 02 16 ページ２０１０年３月９日火曜日午前９時３２分 Controls and displays HDMI OUT – Switch the HDMI output terminal (page 81). SIGNAL SEL – Use to select an input signal (page 62). MCACC – Press to switch between MCACC presets (page 62). SLEEP – Use to put the receiver in sleep mode and select the amount of time before sleep (page 81). CH LEVEL – Press repeatedly to select a channel, then use / to adjust the level (page 116). A.
PAGE 17
SC-37_35_UXJCB.book 17 ページ２０１０年３月９日火曜日午前９時３２分 Controls and displays STREAM DIRECT – Lights when Direct/Pure Direct is selected (page 62). ADV.SURROUND – Lights when one of the Advanced Surround modes has been selected (page 61). STEREO – Lights when stereo listening is switched on (page 61). STANDARD – Lights when one of the Standard Surround modes is switched on (page 59). THX – Lights when one of the Home THX modes is selected (page 60).
PAGE 18
SC-37_35_UXJCB.
PAGE 19
SC-37_35_UXJCB.book 19 ページ２０１０年３月９日火曜日午前９時３２分 Controls and displays 02 11 TUNER EDIT Use with ////ENTER to memorize and name stations for recall (page 52). 12 BAND Switches between AM and FM radio bands (page 52). 13 Listening mode buttons AUTO SURR/ALC/STREAM DIRECT – Switches between Auto Surround (page 59), Auto Level Control, Optimum Surround1 mode and Stream Direct mode (page 62). HOME THX – Press to select a Home THX listening mode (page 60).
PAGE 20
SC-37_35_UXJCB.book 03 20 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment Chapter 3: Connecting your equipment This receiver provides you with many connection possibilities, but it doesn’t have to be difficult. This chapter explains the kinds of components you can connect to make up your home theater system. Important • Illustration shows the SC-37, however connections for the SC-35 are the same except where noted.
PAGE 21
SC-37_35_UXJCB.book 21 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment 03 Note • The input functions below are assigned by default to the receiver’s different input terminals. Refer to The Input Setup menu on page 45 to change the assignments if other connections are used.
PAGE 22
SC-37_35_UXJCB.book 03 22 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment Determining the speakers’ application This unit permits you to build various surround systems, in accordance with the number of speakers you have. [C] 7.1 channel surround system & Speaker B connection • Speaker System setting: Speaker B • Be sure to connect speakers to the front left and right channels (L and R). • It is also possible to only connect one of the surround back speakers (SB) or neither.
PAGE 23
SC-37_35_UXJCB.book 23 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment [E] 5.1 channel surround system & ZONE 2 connection (Multi Zone) • Speaker System setting: ZONE 2 With these connections you can simultaneously enjoy 5.1-channel surround sound in the main zone with stereo playback on another component in ZONE 2. (The selection of input devices is limited.) 03 Placing the speakers Refer to the chart below for placement of the speakers you intend to connect.
PAGE 24
SC-37_35_UXJCB.book 03 24 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment • Place the center speaker above or below the TV so that the sound of the center channel is localized at the TV screen. Also, make sure the center speaker does not cross the line formed by the leading edge of the front left and right speakers. • It is best to angle the speakers towards the listening position. The angle depends on the size of the room. Use less of an angle for bigger rooms.
PAGE 25
SC-37_35_UXJCB.book 25 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment 03 Installing your speaker system At the very least, front left and right speakers only are necessary. Note that your main surround speakers should always be connected as a pair, but you can connect just one surround back speaker if you like (it must be connected to the left surround back terminal). Standard surround connection The front height terminals can also be used for the front wide and Speaker B speakers.
PAGE 26
SC-37_35_UXJCB.
PAGE 27
SC-37_35_UXJCB.book 27 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment 03 ZONE 2 setup Selecting the Speaker system The front height terminals can be used for front wide and Speaker B connections, in addition to for the front height speakers. Also, the surround back terminals can be used for bi-amping and ZONE 2 connections, in addition to for the surround back speakers. Make this setting according to the application. Front height setup With these connections you can simultaneously enjoy 5.
PAGE 28
SC-37_35_UXJCB.book 28 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment 03 If several video components are assigned to the same input function (see The Input Setup menu on page 45), the converter gives priority to HDMI, component, then composite (in that order). High picture quality Terminal for connection with source device Terminal for connection with TV monitor HDMI IN Y PB Y PB The HDMI connection transfers uncompressed digital video, as well as almost every kind of digital audio.
PAGE 29
SC-37_35_UXJCB.book 29 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment 03 Connecting your TV and playback components Connecting using HDMI If you have an HDMI or DVI (with HDCP) equipped component (Blu-ray disc player (BD), etc.), you can connect it to this receiver using a commercially available HDMI cable. If the TV and playback components support the Control with HDMI feature, the convenient Control with HDMI functions can be used (see Control with HDMI function on page 72).
PAGE 30
SC-37_35_UXJCB.book 03 30 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment Connecting your DVD player with no HDMI output This diagram shows connections of a TV (with HDMI input) and DVD player (or other playback component with no HDMI output) to the receiver. DVD player, etc.
PAGE 31
SC-37_35_UXJCB.book 31 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment 03 Connecting your TV with no HDMI input This diagram shows connections of a TV (with no HDMI input) and DVD player (or other playback component) to the receiver. • With these connections, the picture is not output to the TV even if the DVD player is connected with an HDMI cable. Connect the DVD player’s video signals using a composite or component cord. DVD player, etc.
PAGE 32
SC-37_35_UXJCB.book 03 32 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment Connecting an HDD/DVD recorder, BD recorder and other video sources This receiver has two sets of audio/video inputs and outputs suitable for connecting analog or digital video devices, including HDD/DVD recorders and BD recorders. When you set up the receiver you’ll need to tell the receiver which input you connected the recorder to (see also The Input Setup menu on page 45). HDD/DVD recorder, BD recorder, etc.
PAGE 33
SC-37_35_UXJCB.book 33 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment 03 Connecting a satellite/cable receiver or other set-top box Satellite and cable receivers, and terrestrial digital TV tuners are all examples of so-called ‘set-top boxes’. When you set up the receiver you’ll need to tell the receiver which input you connected the set-top box to (see The Input Setup menu on page 45).
PAGE 34
SC-37_35_UXJCB.book 03 34 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment Connecting the multichannel analog inputs For DVD Audio and SACD playback, your DVD player may have 5.1, 6.1 or 7.1 channel analog outputs (depending on whether your player supports surround back channels). Make sure that the player is set to output multichannel analog audio. DVD player, etc.
PAGE 35
SC-37_35_UXJCB.book 35 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment 03 Connecting other audio components This receiver has both digital and analog inputs, allowing you to connect audio components for playback. Most digital components also have analog connections. When you set up the receiver you’ll need to tell the receiver which input you connected the component to (see also The Input Setup menu on page 45). CD-R, MD, DAT, etc.
PAGE 36
SC-37_35_UXJCB.book 03 36 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment Connecting additional amplifiers Connecting AM/FM antennas This receiver has more than enough power for any home use, but it’s possible to add additional amplifiers to every channel of your system using the pre-outs. Make the connections shown below to add amplifiers to power your speakers. Connect the AM loop antenna and the FM wire antenna as shown below.
PAGE 37
SC-37_35_UXJCB.book 37 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment 03 Connecting external antennas Making MULTI-ZONE connections To improve FM reception, connect an external FM antenna to FM UNBAL 75 Ω. It is possible to make these connections if you have a separate TV and speakers for your primary (ZONE 2) sub zone, and a separate TV and a separate amplifier (and speakers) for your secondary (ZONE 3) sub zone.
PAGE 38
SC-37_35_UXJCB.book 03 38 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment MULTI-ZONE setup using speaker terminals (ZONE 2) You must select ZONE 2 in Speaker system setting on page 115 to use this setup. Connecting to the network through LAN interface • Connect a TV monitor to the VIDEO ZONE 2 OUT jacks on this receiver.1 You should have a pair of speakers attached to the surround back speaker terminals as shown below.
PAGE 39
SC-37_35_UXJCB.book 39 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment Connecting Optional Bluetooth ® ADAPTER When the Bluetooth ADAPTER (Pioneer Model No. ASBT100)1 is connected to this receiver, a product equipped with Bluetooth wireless technology (portable cell phone, digital music player, etc.) can be used to listen to music wirelessly.
PAGE 40
SC-37_35_UXJCB.book 03 40 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment Connecting an iPod This receiver has a dedicated iPod terminal that will allow you to control playback of audio content from your iPod using the controls of this receiver. • Switch the receiver into standby then use the supplied iPod cable to connect your iPod to the iPod/ iPhone/USB terminal on the front panel of this receiver.
PAGE 41
SC-37_35_UXJCB.book 41 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment Connecting an IR receiver If you keep your stereo components in a closed cabinet or shelving unit, or you wish to use the sub zone remote control in another zone, you can use an optional IR receiver (such as a Niles or Xantech unit) to control your system instead of the remote sensor on the front panel of this receiver.1 1 Connect the IR receiver sensor to the IR IN jack on the rear of this receiver.
PAGE 42
SC-37_35_UXJCB.book 03 42 ページ２０１０年３月９日火曜日午前９時３２分 Connecting your equipment Switching components on and off using the 12 volt trigger You can connect components in your system (such as a screen or projector) to this receiver so that they switch on or off using 12 volt triggers when you select an input function. However, you must specify which input functions switch on the trigger using the The Input Setup menu on page 45. Note that this will only work with components that have a standby mode.
PAGE 43
SC-37_35_UXJCB.book 43 ページ２０１０年３月９日火曜日午前９時３２分 Basic Setup 04 Chapter 4: Basic Setup Important • The procedure for setting the receiver operation mode differs for the remote controls included with the SC-37 and SC-35. For the SC-37’s remote control, set the remote control operation selector switch to RECEIVER. For the SC-35’s remote control, press the RECEIVER button.
PAGE 44
SC-37_35_UXJCB.book 04 44 ページ２０１０年３月９日火曜日午前９時３２分 Basic Setup Make sure there are no obstacles between the speakers and the microphone.
PAGE 45
SC-37_35_UXJCB.book 45 ページ２０１０年３月９日火曜日午前９時３２分 Basic Setup • If you see an ERR message (or the speaker configuration displayed isn’t correct), there may be a problem with the speaker connection. If selecting RETRY doesn’t work, turn off the power and check the speaker connections. If there doesn’t seem to be a problem, you can simply use / to select the speaker and / to change the setting and continue. • If Reverse Phase is displayed, the speaker’s wiring (+ and –) may be inverted.
PAGE 46
SC-37_35_UXJCB.book 04 46 ページ２０１０年３月９日火曜日午前９時３２分 Basic Setup • Input Skip – When set to ON, that input is skipped when selecting the input using INPUT SELECT. (DVD and other inputs can be still be selected directly with the input function buttons.
PAGE 47
SC-37_35_UXJCB.book 47 ページ２０１０年３月９日火曜日午前９時３２分 Basic playback 05 Chapter 5: Basic playback Important • The procedure for setting the receiver operation mode differs for the remote controls included with the SC-37 and SC-35. For the SC-37’s remote control, set the remote control operation selector switch to RECEIVER. For the SC-35’s remote control, press the RECEIVER button.
PAGE 48
SC-37_35_UXJCB.book 48 ページ２０１０年３月９日火曜日午前９時３２分 Basic playback 05 Playing an iPod This receiver has the iPod/iPhone/USB terminal that will allow you to control playback of audio content from your iPod using the controls of this receiver.1 1 Switch on the receiver and your TV. See Connecting an iPod on page 40. • It is also possible to operate the iPod on the iPod itself, without using the TV screen. For details, see Switching the iPod controls on page 49.
PAGE 49
SC-37_35_UXJCB.book 49 ページ２０１０年３月９日火曜日午前９時３２分 Basic playback 05 Switching the iPod controls1 You can switch over the iPod controls between the iPod and the receiver. 1 Press iPod CTRL to switch the iPod controls. This enables operation and display on your iPod, and this receiver’s remote control and GUI screen become inactive. 2 Press iPod CTRL again to switch back to the receiver controls. Playing a USB device It is possible to play files2 using the USB interface on the front of this receiver.
PAGE 50
SC-37_35_UXJCB.book 05 50 ページ２０１０年３月９日火曜日午前９時３２分 Basic playback 3 Continue browsing until you arrive at what you want to play, then press  to start playback.1 Basic playback controls Button(s) What it does Basic playback controls ENTER,  Starts displaying a photo and playing a slideshow. This receiver’s remote control buttons can be used for basic playback of files stored on USB memory devices. RETURN,  Stops the player and returns to the previous menu.
PAGE 51
SC-37_35_UXJCB.book 51 ページ２０１０年３月９日火曜日午前９時３２分 Basic playback 05 About playable file formats The USB function of this receiver supports the following file formats. Note that some file formats are not available for playback although they are listed as playable file formats. Music files Category Extension Stream MP3a .mp3 MPEG-1, 2, 2.5 Audio Layer-3 WAV WMA .wav .
PAGE 52
SC-37_35_UXJCB.book 52 ページ２０１０年３月９日火曜日午前９時３２分 Basic playback 05 Tuning directly to a station Listening to the radio The following steps show you how to tune in to FM and AM radio broadcasts using the automatic (search) and manual (step) tuning functions. If you already know the frequency of the station you want, see Tuning directly to a station below. Once you are tuned to a station you can memorize the frequency for recall later—see Saving station presets below for more on how to do this.
PAGE 53
SC-37_35_UXJCB.book 53 ページ２０１０年３月９日火曜日午前９時３２分 Basic playback Naming station presets For easier identification, you can name your station presets. 05 Family friendly packages are also available to restrict channels featuring content that may be inappropriate for children. 1 Choose the station preset you want to name. See Listening to station presets on page 52 for how to do this. To subscribe to XM, U.S. customers should visit xmradio.
PAGE 54
SC-37_35_UXJCB.book 54 ページ２０１０年３月９日火曜日午前９時３２分 Basic playback 05 • The currently selected channel is automatically chosen (without pressing ENTER) after five seconds. Using the XM Menu The XM Menu provides additional XM Radio features.2 Using XM HD Surround 1 XM HD Surround uses Neural Surround™ technologies to achieve optimal surround sound from XM radio. XM HD Surround Sound is available on select XM channels only. 2 Use / to select a menu item, then press ENTER.
PAGE 55
SC-37_35_UXJCB.book 55 ページ２０１０年３月９日火曜日午前９時３２分 Basic playback 05 Selecting channels and browsing by genre Using the SIRIUS Menu From the SIRIUS Channel Guide, you can browse SIRIUS Radio channels in the order that they appear, or you can narrow your channel search by genre. The SIRIUS Menu provides additional SIRIUS Radio features.2 1 Press / to enter the SIRIUS Channel Guide, navigate through the channels one at time with /, then press ENTER to listen to the SIRIUS radio broadcast.
PAGE 56
SC-37_35_UXJCB.book 05 56 ページ２０１０年３月９日火曜日午前９時３２分 Basic playback Listening to Internet radio stations (SC-35 only) Tip • This section describes how to listen to Internet radio on the SC-35. On the SC-37, Internet radio is operated with Home Media Gallery. For details, see Playback with HOME MEDIA GALLERY inputs (SC-37 only) on page 64. Internet radio is an audio broadcasting service transmitted via the Internet.
PAGE 57
SC-37_35_UXJCB.book 57 ページ２０１０年３月９日火曜日午前９時３２分 Basic playback 05 1 Turn on the computer and launch the Internet browser. 2 In the address bar on the browser, enter the IP address assigned to this receiver. For example, if the IP address of this receiver is “192.168.0.2”, enter “http://192.168.0.2/”. Bluetooth ADAPTER for Wireless Enjoyment of Music When the connection is made with the receiver, a Top Menu will be displayed.
PAGE 58
SC-37_35_UXJCB.book 58 ページ２０１０年３月９日火曜日午前９時３２分 Basic playback 05 Pairing the Bluetooth ADAPTER and Bluetooth wireless technology device “Pairing” must be done before you start playback of Bluetooth wireless technology content using the Bluetooth ADAPTER. Make sure to perform pairing the first time you operate the system or any time pairing data is cleared. The pairing step is necessary to register the Bluetooth wireless technology device to enable Bluetooth communications.
PAGE 59
SC-37_35_UXJCB.book 59 ページ２０１０年３月９日火曜日午前９時３２分 Listening to your system 06 Chapter 6: Listening to your system Important • The procedure for setting the receiver operation mode differs for the remote controls included with the SC-37 and SC-35. For the SC-37’s remote control, set the remote control operation selector switch to RECEIVER. For the SC-35’s remote control, press the RECEIVER button.
PAGE 60
SC-37_35_UXJCB.book 06 60 ページ２０１０年３月９日火曜日午前９時３２分 Listening to your system • 2 Pro Logic IIz HEIGHT – Up to 7.1 channel sound (front height)1 1 Set the remote control to the receiver operation mode. • WIDE SURROUND MOVIE – Up to 7.1 channel sound (front wide), especially suited to movie sources2 • Press THX (HOME THX) to select a listening mode.
PAGE 61
SC-37_35_UXJCB.book 61 ページ２０１０年３月９日火曜日午前９時３２分 Listening to your system Using the Advanced surround effects The Advanced surround effects can be used for a variety of additional surround sound effects. Most Advanced Surround modes are designed to be used with film soundtracks, but some modes are also suited for music sources. Try different settings with various soundtracks to see which you like. 1 Set the remote control to the receiver operation mode.
PAGE 62
SC-37_35_UXJCB.book 06 62 ページ２０１０年３月９日火曜日午前９時３２分 Listening to your system Using Stream Direct Use the Stream Direct modes when you want to hear the truest possible reproduction of a source. All unnecessary signal processing is bypassed, and you’re left with the pure analog or digital sound source. Processing differs depending on the input signal and whether or not surround back speakers are connected.
PAGE 63
SC-37_35_UXJCB.book 63 ページ２０１０年３月９日火曜日午前９時３２分 Listening to your system 06 Phase Control technology provides coherent sound reproduction through the use of phase matching1 for an optimal sound image. The default setting is on and we recommend leaving Phase Control switched on for all sound sources. where the group delay characteristics are not effectively flattened.
PAGE 64
SC-37_35_UXJCB.book 07 64 ページ２０１０年３月９日火曜日午前９時３２分 Playback with HOME MEDIA GALLERY inputs (SC-37 only) Chapter 7: Playback with HOME MEDIA GALLERY inputs (SC-37 only) Introduction Enjoying the Home Media Gallery This receiver’s Home Media Gallery function allows you to listen to audio files or listen to Internet radio stations on a computer or other component connected to the receiver’s LAN terminal. This chapter describes the setup and playback procedures required to enjoy these features.
PAGE 65
SC-37_35_UXJCB.book 65 ページ２０１０年３月９日火曜日午前９時３２分 Playback with HOME MEDIA GALLERY inputs (SC-37 only) the PC. The authorization (or permission) method for access varies depending on the type of server currently being connected. For more information on authorizing this receiver, refer to the instruction manual of your server. Playback with Home Media Gallery Important • When you play back audio files, ‘Connecting...’ is displayed before playback starts.
PAGE 66
SC-37_35_UXJCB.book 07 66 ページ２０１０年３月９日火曜日午前９時３２分 Playback with HOME MEDIA GALLERY inputs (SC-37 only) Use / to select ‘Help’, then press ENTER. Listening to Internet radio stations 2 Internet radio is an audio broadcasting service transmitted via the Internet. There are a large number of Internet radio stations broadcasting a variety of services from every corner of the world.
PAGE 67
SC-37_35_UXJCB.book 67 ページ２０１０年３月９日火曜日午前９時３２分 Playback with HOME MEDIA GALLERY inputs (SC-37 only) 07 Listening to Sirius Internet Radio Check the website below to listen to Sirius Internet Radio: http://www.sirius.com/siriusinternetradio • You must have a registered account in order to listen to songs using Sirius Internet Radio. For details, see Checking about the Accounts on page 68. • Some functions may be changed at Sirius’s discretion.
PAGE 68
SC-37_35_UXJCB.book 68 ページ２０１０年３月９日火曜日午前９時３２分 Playback with HOME MEDIA GALLERY inputs (SC-37 only) 07 DLNA Checking about the Accounts Screen concerning Rhapsody or Sirius Internet Radio account registration. Before proceeding with the following steps, check whether you have followed Steps from 1 to 2 on page 65. 1 Select ‘Setup’ then press ENTER. 2 Select Accounts and press ENTER to confirm your selection. 3 Select Rhapsody or Sirius and press ENTER.
PAGE 69
SC-37_35_UXJCB.book 69 ページ２０１０年３月９日火曜日午前９時３２分 Playback with HOME MEDIA GALLERY inputs (SC-37 only) 07 About playback behavior over a network • Playback may stall when the PC is switched off or any media files stored on it are deleted while playing content. • If there are problems within the network environment (heavy network traffic, etc.) content may not be displayed or played properly (playback may be interrupted or stalled).
PAGE 70
SC-37_35_UXJCB.book 07 70 ページ２０１０年３月９日火曜日午前９時３２分 Playback with HOME MEDIA GALLERY inputs (SC-37 only) About playable file formats The Home Media Gallery feature of this receiver supports the following file formats. Note that some file formats are not available for playback although they are listed as playable file formats. Also, the compatibility of file formats varies depending on the type of server. Check with your server to ensure the compatibility of file formats supported by your server.
PAGE 71
SC-37_35_UXJCB.book 71 ページ２０１０年３月９日火曜日午前９時３２分 Playback with HOME MEDIA GALLERY inputs (SC-37 only) 07 Glossary aacPlus AAC decoder uses aacPlus developed by Coding Technologies. (www.codingtechnologies.com) Windows Media Player 11/ Windows Media Player 12 Windows Media Player is software to deliver music, photos and movies from a Microsoft Windows computer to home stereo systems and TVs.
PAGE 72
SC-37_35_UXJCB.book 08 72 ページ２０１０年３月９日火曜日午前９時３２分 Control with HDMI function Chapter 8: Control with HDMI function Important • The procedure for setting the receiver operation mode differs for the remote controls included with the SC-37 and SC-35. For the SC-37’s remote control, set the remote control operation selector switch to RECEIVER. For the SC-35’s remote control, press the RECEIVER button.
PAGE 73
SC-37_35_UXJCB.book 73 ページ２０１０年３月９日火曜日午前９時３２分 Control with HDMI function HDMI Setup You must adjust the settings of this receiver as well as the connected Control with HDMI-compatible components in order to make use of the Control with HDMI function. For more information see the operating instructions for each component. 08 8 Select the ‘Standby Through’ setting you want.
PAGE 74
SC-37_35_UXJCB.book 08 74 ページ２０１０年３月９日火曜日午前９時３２分 Control with HDMI function About synchronized operations The Control with HDMI-compatible component connected to the receiver operates in sync as described below. • From the menu screen of the Control with HDMIcompatible TV, set audio to be played through this receiver, and the receiver will switch to the synchronized amp mode. • When in the synchronized amp mode, you can adjust the receiver’s volume or mute the sound using the TV’s remote control.
PAGE 75
SC-37_35_UXJCB.book 75 ページ２０１０年３月９日火曜日午前９時３２分 Control with HDMI function Setting the PQLS function PQLS (Precision Quartz Lock System) is a digital audio signal transfer control technology using the Control with HDMI function. It offers higher-quality audio playback by controlling audio signals from the receiver to a PQLS compatible player, etc. This enables removing jitter that has a negative effect on the quality of the sound and is generated upon transmission.
PAGE 76
SC-37_35_UXJCB.book 76 ページ２０１０年３月９日火曜日午前９時３２分 Using other functions 09 Chapter 9: Using other functions Important • The procedure for setting the receiver operation mode differs for the remote controls included with the SC-37 and SC-35. For the SC-37’s remote control, set the remote control operation selector switch to RECEIVER. For the SC-35’s remote control, press the RECEIVER button.
PAGE 77
SC-37_35_UXJCB.book 77 ページ２０１０年３月９日火曜日午前９時３２分 Using other functions 09 Setting What it does Option(s) Setting What it does DUAL (Dual Mono) Specifies how dual mono encoded Dolby Digital soundtracks should be played. Dual mono is not widely used, but is sometimes necessary when two languages need to be sent to separate channels.
PAGE 78
SC-37_35_UXJCB.book 09 78 ページ２０１０年３月９日火曜日午前９時３２分 Using other functions f. • The HDMI Audio setting cannot be switched while performing synchronized amp mode operations. • The synchronized amp mode must be turned on in order to play the receiver’s HDMI audio and video input signals from the TV with the receiver’s power in the standby mode. See About synchronized operations on page 74. g.
PAGE 79
SC-37_35_UXJCB.book 79 ページ２０１０年３月９日火曜日午前９時３２分 Using other functions 09 Setting What it does BRIGHTd Adjusts the overall brightness. –6 to +6 Default: 0 CONTRASTd Adjusts the contrast between light and dark. –6 to +6 Default: 0 HUEd Adjusts the red/green balance. –6 to +6 Default: 0 CHROMAd (Chroma Level) Adjusts saturation from dull to bright. –6 to +6 Default: 0 (Brightness) BLK SETUPf Corrects the black depth in the brightness signal. Normally select 7.5.
PAGE 80
SC-37_35_UXJCB.book 80 ページ２０１０年３月９日火曜日午前９時３２分 Using other functions 09 • When the receiver is on,1 make sure that any operations for the sub zone are done while ZONE and your selected sub zone(s) show in the display. If this is not showing, the front panel controls affect the main zone only. 3 Use the INPUT SELECTOR dial to select the source for the zone you have selected. For example, ZONE 2 CD-R sends the source connected to the CD-R inputs to the primary (ZONE 2) sub room.
PAGE 81
SC-37_35_UXJCB.book 81 ページ２０１０年３月９日火曜日午前９時３２分 Using other functions 09 Using the sleep timer Using the Web Control function The sleep timer switches the receiver into standby after a specified amount of time so you can fall asleep without worrying about the receiver being left on all night. Use the remote control to set the sleep timer. The receiver can be operated using a browser from a computer connected on the same LAN as the receiver.
PAGE 82
SC-37_35_UXJCB.book 82 ページ２０１０年３月９日火曜日午前９時３２分 Using other functions 09 Setting Resetting the system DSP Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this. Set MULTI-ZONE to OFF. Power On Level • Disconnect the iPod and USB memory device from the receiver beforehand. Phase Control 1 OFF Mute Level FULL Sound Retriever Switch the receiver into standby.
PAGE 83
SC-37_35_UXJCB.book 83 ページ２０１０年３月９日火曜日午前９時３２分 Controlling the rest of your system (In case of SC-37) 10 Chapter 10: Controlling the rest of your system (In case of SC-37) Important • This section includes explanations for the SC-37’s remote control. For instructions for the SC-35’s remote control, see Controlling the rest of your system (In case of SC-35) on page 96. About the Remote Setup menu The Remote Setup mode is set by pressing the HOME MENU button while pressing MULTI OPERATION.
PAGE 84
SC-37_35_UXJCB.book 10 84 ページ２０１０年３月９日火曜日午前９時３２分 Controlling the rest of your system (In case of SC-37) Operating multiple receivers The remote control included with this receiver can be used to operate up to three other receivers (of the same model as this receiver) in addition to this receiver. The receiver to be operated is switched by inputting the preset code to set the remote control setting.
PAGE 85
SC-37_35_UXJCB.book 85 ページ２０１０年３月９日火曜日午前９時３２分 Controlling the rest of your system (In case of SC-37) • If you can’t find or properly enter a preset code, you can still teach the remote individual commands from another remote control (see Programming signals from other remote controls below). 7 If your component is controlled successfully, press ENTER to confirm. The remote display shows OK.
PAGE 86
SC-37_35_UXJCB.book 86 ページ２０１０年３月９日火曜日午前９時３２分 Controlling the rest of your system (In case of SC-37) 10 2 Use / to select ‘ERASE LEARNING’, then press ENTER. The remote display prompts you for the component corresponding to the button setting to be erased. 3 Press the input function button corresponding to the command to be erased, then press ENTER. The remote display flashes PRESS KEY. 4 Press and hold the button to be erased for two seconds.
PAGE 87
SC-37_35_UXJCB.book 87 ページ２０１０年３月９日火曜日午前９時３２分 Controlling the rest of your system (In case of SC-37) 10 remote control to set up and listen to a CD on the receiver, and then use the remote control to rewind a tape in your VCR while you continue to listen to your CD player. 3 Press the input function button for the component that will start the multi-operation, then press ENTER. For example, if you want to start the sequence by switching on your DVD player, press DVD.
PAGE 88
SC-37_35_UXJCB.book 10 88 ページ２０１０年３月９日火曜日午前９時３２分 Controlling the rest of your system (In case of SC-37) 8 Repeat steps 5 to 7 to program a sequence of up to commands. 9 When you’re finished, use / to select ‘EDIT EXIT’ from the menu and press ENTER. You will return to the remote control Setup menu. Select EXIT SETUP to exit. Using multi operations You can start multi operations with the receiver switched on, or in standby.
PAGE 89
SC-37_35_UXJCB.
PAGE 90
SC-37_35_UXJCB.
PAGE 91
SC-37_35_UXJCB.book 91 ページ２０１０年３月９日火曜日午前９時３２分 Controlling the rest of your system (In case of SC-37) 10 Using the RF communications function IR blaster (only required when you want to operate other components by RF two-way communications) (max.
PAGE 92
SC-37_35_UXJCB.book 92 ページ２０１０年３月９日火曜日午前９時３２分 Controlling the rest of your system (In case of SC-37) 10 Pairing the RF adapter and remote control Pairing is necessary in order to use the RF communications function. Perform the operation below after connecting the RF adapter and receiver. 1 Switch on the receiver. 3 Use / to select the receiver zone for which you want to use RF two-way communications, then press ENTER. 4 Use / to select ‘RF MODE’, then press ENTER.
PAGE 93
SC-37_35_UXJCB.book 93 ページ２０１０年３月９日火曜日午前９時３２分 Controlling the rest of your system (In case of SC-37) 1 Connect the IR blaster cable to the RF Adapter’s IR Blaster terminal and mount the transmitter on the component you want to operate with RF communications. 10 Renaming input function names in synchrony with the receiver • Default setting: MANUAL RF adapter • Operation is not possible unless the IR blaster is mounted in an appropriate position.
PAGE 94
SC-37_35_UXJCB.book 10 94 ページ２０１０年３月９日火曜日午前９時３２分 Controlling the rest of your system (In case of SC-37) Setting the remote control operation mode 1 Examples of common devices utilizing the 2.4 GHz band: • Cordless phone • Cordless facsimile • Default setting: ON • Microwave oven When the remote control operation mode is turned on and the receiver’s input is switched, the remote control display and operation mode switch automatically to that input.
PAGE 95
SC-37_35_UXJCB.book 95 ページ２０１０年３月９日火曜日午前９時３２分 Controlling the rest of your system (In case of SC-37) Usable range • Designed for use only within private homes (signal transmission distance may be reduced due to room design or conditions). In the following cases, this remote control cannot operate due to poor or erratic radio wave transmission. • When signal transmission is blocked by a wall or floor constructed of ferro-concrete or metal.
PAGE 96
SC-37_35_UXJCB.book 10 96 ページ２０１０年３月９日火曜日午前９時３２分 Controlling the rest of your system (In case of SC-35) Controlling the rest of your system (In case of SC-35) Important • This section includes explanations for the SC-35’s remote control. For instructions for the SC-37’s remote control, see Controlling the rest of your system (In case of SC-37) on page 83. About the Remote Setup menu The Remote Setup mode is set by pressing the number button while pressing R.SETUP.
PAGE 97
SC-37_35_UXJCB.book 97 ページ２０１０年３月９日火曜日午前９時３２分 Controlling the rest of your system (In case of SC-35) Setting the remote to control other components Most components can be assigned to one of the input function buttons (such as DVD or CD) using the component’s manufacturer preset code stored in the remote.
PAGE 98
SC-37_35_UXJCB.book 98 ページ２０１０年３月９日火曜日午前９時３２分 Controlling the rest of your system (In case of SC-35) 10 3 Point the two remote controls towards each other, then press the button that will be doing the learning on this receiver’s remote control. The LED blinks once and flashes continuously. • The remote controls should be 3 cm (1 inch) apart. Other remote control 4 Press the corresponding button on the other remote control that is sending (teaching) the signal to this receiver’s remote control.
PAGE 99
SC-37_35_UXJCB.book 99 ページ２０１０年３月９日火曜日午前９時３２分 Controlling the rest of your system (In case of SC-35) Setting the backlight mode • Default setting: 1 (normal mode) The backlight lighting pattern can be selected from among four modes, in consideration of convenience and battery service life. 1 Press and hold R.SETUP, then press “6” for three seconds. The LED flashes continuously. • To cancel the preset setup mode press R.SETUP. 2 Press the number button for the backlight mode you want to set.
PAGE 100
SC-37_35_UXJCB.book 100 ページ２０１０年３月９日火曜日午前９時３２分 Controlling the rest of your system (In case of SC-35) 10 Programming a Multi operation or a shutdown sequence 1 Press and hold R.SETUP, then press “3” for three seconds. The LED flashes continuously. • To cancel the preset setup mode press R.SETUP. 2 Press the input function button (or  SOURCE button).
PAGE 101
SC-37_35_UXJCB.book 101 ページ２０１０年３月９日火曜日午前９時３２分 Controlling the rest of your system (In case of SC-35) 10 Resetting the remote control settings Controlling components Use this procedure to reset all the remote control’s settings to the factory default.1 This remote control can control components after entering the proper codes (see Setting the remote to control other components on page 97 for more on this). Use the input function buttons to select the component. 1 Press and hold R.
PAGE 102
SC-37_35_UXJCB.
PAGE 103
SC-37_35_UXJCB.
PAGE 104
SC-37_35_UXJCB.book 104 ページ２０１０年３月９日火曜日午前９時３２分 The Advanced MCACC menu 11 Chapter 11: The Advanced MCACC menu Important • The procedure for setting the receiver operation mode differs for the remote controls included with the SC-37 and SC-35. For the SC-37’s remote control, set the remote control operation selector switch to RECEIVER. For the SC-35’s remote control, press the RECEIVER button.
PAGE 105
SC-37_35_UXJCB.book 105 ページ２０１０年３月９日火曜日午前９時３２分 The Advanced MCACC menu 2 Select the parameters you want to set. Use / to select the item, then use / to set. • Auto MCACC – The default is ALL (recommended), but you can limit the system calibration to only one setting (to save time) if you want.1 11 3 Connect the microphone to the MCACC SETUP MIC jack on the front panel. Make sure there are no obstacles between the speakers and the microphone.
PAGE 106
SC-37_35_UXJCB.book 11 106 ページ２０１０年３月９日火曜日午前９時３２分 The Advanced MCACC menu If no operations are performed for 10 seconds while the speaker configuration check screen is being displayed, the Auto MCACC Setup will resume automatically. In this case, you don’t need to select ‘OK’ and press ENTER in step 8. • If you see an ERR message (or the speaker configuration displayed isn’t correct), there may be a problem with the speaker connection.
PAGE 107
SC-37_35_UXJCB.book 107 ページ２０１０年３月９日火曜日午前９時３２分 The Advanced MCACC menu • Standing Wave – Control overly resonant low frequencies in your listening room (see Standing Wave on page 107). The last two settings are specifically for customizing the parameters explained in Acoustic Calibration EQ Adjust on page 108: • EQ Adjust – Manually adjust the frequency balance of your speaker system while listening to test tones (see Acoustic Calibration EQ Adjust on page 108).
PAGE 108
SC-37_35_UXJCB.book 11 108 ページ２０１０年３月９日火曜日午前９時３２分 The Advanced MCACC menu it results in an overly resonant (‘boomy’) sound. The Standing Wave Control uses filters to reduce the effect of overly resonant sounds in your listening area. During playback of a source, you can customize the filters used for Standing Wave Control for each of your MCACC presets.1 Tip • Changing the frequency curve of one channel too drastically will affect the overall balance.
PAGE 109
SC-37_35_UXJCB.book 109 ページ２０１０年３月９日火曜日午前９時３２分 The Advanced MCACC menu Using Acoustic Calibration EQ Professional 1 2 Select ‘EQ Professional’, then press ENTER. Select an option and press ENTER. • Reverb Measurement – Use this to measure the reverb characteristics before and after calibration. • Reverb View – You can check the reverb measurements made for specified frequency ranges in each channel.
PAGE 110
SC-37_35_UXJCB.book 11 110 ページ２０１０年３月９日火曜日午前９時３２分 The Advanced MCACC menu Precision Distance (SC-37 only) Before using this function, perform the Full Auto MCACC Setup procedure (see page 43). Performing the Full Auto MCACC procedure corrects the distance to a precision of 1/2 inch, but the Precision Distance function lets you adjust the distance to the speakers (their position) with a precision of under 1/2 inch.
PAGE 111
SC-37_35_UXJCB.book 111 ページ２０１０年３月９日火曜日午前９時３２分 The Advanced MCACC menu 4 Press RETURN to go back to the MCACC Data Check menu, repeating steps 2 and 3 to check other settings. 5 When you’re finished, press RETURN. You will return to the Home Menu. Speaker Setting Use this to display the speaker size and number of speakers. See Speaker Setting on page 115 for more on this. 1 Select ‘Speaker Setting’ from the MCACC Data Check menu. 2 Select the channel you want to check.
PAGE 112
SC-37_35_UXJCB.book 11 112 ページ２０１０年３月９日火曜日午前９時３２分 The Advanced MCACC menu Output MCACC data Before continuing, make sure you have completed step 2 in Checking MCACC Data on page 110. The data measured with the Advanced MCACC function is transmitted to the USB device.1 The 3D graphs of the reverb characteristics and group delay characteristics2 before and after calibration and the MCACC results (parameters) can be checked on your computer.
PAGE 113
SC-37_35_UXJCB.book 113 ページ２０１０年３月９日火曜日午前９時３２分 The Advanced MCACC menu 11 Copying MCACC preset data If you want to manually adjust the Acoustic Calibration EQ (see Manual MCACC setup on page 106), we recommend copying your current settings1 to an unused MCACC preset. Instead of just a flat EQ curve, this will give you a reference point from which to start. 1 Select ‘MCACC Memory Copy’ from the Data Management setup menu. 2 Select the setting you want to copy.
PAGE 114
SC-37_35_UXJCB.book 114 ページ２０１０年３月９日火曜日午前９時３２分 The System Setup and Other Setup menus 12 Chapter 12: The System Setup and Other Setup menus Important • The procedure for setting the receiver operation mode differs for the remote controls included with the SC-37 and SC-35. For the SC-37’s remote control, set the remote control operation selector switch to RECEIVER. For the SC-35’s remote control, press the RECEIVER button.
PAGE 115
SC-37_35_UXJCB.book 115 ページ２０１０年３月９日火曜日午前９時３２分 The System Setup and Other Setup menus Speaker system setting • Default setting: Normal(SB/FH) There are several ways you can use the speaker terminals with this receiver. In addition to a normal home theater setup where they are used for the front height speakers or front wide speakers, they can be used for bi-amping the front speakers or as an independent speaker system in another room. 1 Select ‘Speaker System’ from the Manual SP Setup menu.
PAGE 116
SC-37_35_UXJCB.book 116 ページ２０１０年３月９日火曜日午前９時３２分 The System Setup and Other Setup menus 12 3 Confirm your selected setup option. The test tones will start after you press ENTER. • SB – Select the number of surround back speakers you have (one, two or none).1 Select LARGEx2 or LARGEx1 if your surround back speakers reproduce bass frequencies effectively. Select SMALLx2 or SMALLx1 to send bass frequencies to the other speakers or subwoofer. If you didn’t connect surround back speakers choose NO.
PAGE 117
SC-37_35_UXJCB.book 117 ページ２０１０年３月９日火曜日午前９時３２分 The System Setup and Other Setup menus X-Curve Most soundtracks mixed for cinema sound too bright when played back in large rooms. The X-Curve setting acts as a kind of re-equalization for home theater listening, and restores proper tonal balance of movie soundtracks.1 1 Select ‘X-Curve’ from the Manual SP Setup menu. 2 Choose the X-Curve setting you want. Use / to adjust the setting.
PAGE 118
SC-37_35_UXJCB.book 12 118 ページ２０１０年３月９日火曜日午前９時３２分 The System Setup and Other Setup menus IP address/Proxy setting In case the router connected to the LAN terminal on this receiver is a broadband router (with a built-in DHCP server function), simply turn on the DHCP server function, and you will not need to set up the network manually. You must set up the network as described below only when you have connected this receiver to a broadband router without a DHCP server function.
PAGE 119
SC-37_35_UXJCB.book 119 ページ２０１０年３月９日火曜日午前９時３２分 The System Setup and Other Setup menus 12 Volume Setup The Other Setup menu The Other Setup menu is where you can make customized settings to reflect how you are using the receiver. 1 Set the remote control to the receiver operation mode, then press HOME MENU. A Graphical User Interface (GUI) screen appears on your TV. Use /// and ENTER to navigate through the screens and select menu items. Press RETURN to confirm and exit the current menu.
PAGE 120
SC-37_35_UXJCB.book 120 ページ２０１０年３月９日火曜日午前９時３２分 The System Setup and Other Setup menus 12 Flicker Reduction Setup • Default setting: OFF The GUI screen’s resolution can be increased. If you feel the GUI screen is hard to see, try changing this setting. Note that the resolution in this setting only affects the GUI screen; it has no influence on the video output. 1 Select ‘Flicker Reduction Setup’ from the Other Setup menu. 2 Select the Flicker Reduction setting you want.
PAGE 121
SC-37_35_UXJCB.book 121 ページ２０１０年３月９日火曜日午前９時３２分 Additional information 13 Chapter 13: Additional information Speaker Setting Guide In order to achieve an even better surround effect, it is important to accurately position the speakers and make their volume and tone characteristics uniform so as to finely focus the multi-channel sound. The three major elements in positioning the speakers are distance, angle and orientation (the direction in which the speakers are pointing).
PAGE 122
SC-37_35_UXJCB.book 13 122 ページ２０１０年３月９日火曜日午前９時３２分 Additional information Position of center speaker and monitor Tip • The distance to the subwoofer may be slightly larger than the distance actually measured with a tape measure, etc. This is because this distance is corrected for electric delay, and is not a problem.
PAGE 123
SC-37_35_UXJCB.book 123 ページ２０１０年３月９日火曜日午前９時３２分 Additional information Symptom Remedy During loud playback the power suddenly switches off. • Turn down the volume. • Lower the 63 Hz and 125 Hz equalizer levels in the Manual MCACC setup on page 106. • Switch on the digital safety feature. While holding down ENTER on the front panel, press  STANDBY/ON to set this receiver to the standby mode. Use TUNE / to select D.SAFETY OFF, and then use PRESET / to select 1 or 2 (select D.
PAGE 124
SC-37_35_UXJCB.book 13 124 ページ２０１０年３月９日火曜日午前９時３２分 Additional information Symptom Remedy No sound from subwoofer. • Check that the subwoofer is connected properly, switched on and the volume turned up. • If your subwoofer has a sleep function, make sure it is switched off. • Make sure that the Subwoofer setting is YES or PLUS (see Speaker Setting on page 115).
PAGE 125
SC-37_35_UXJCB.book 125 ページ２０１０年３月９日火曜日午前９時３２分 Additional information Symptom 13 Remedy The PHASE CONTROL feature • If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass cutoff is doesn’t seem to have an set to the highest frequency setting. If there is a PHASE setting on your subwoofer, set it to 0º (or audible effect. depending on the subwoofer, the setting where you think it has the best overall effect on the sound).
PAGE 126
SC-37_35_UXJCB.book 13 126 ページ２０１０年３月９日火曜日午前９時３２分 Additional information Symptom Remedy Can’t record video. • Check that the source is not copy-protected. • The video converter is not available when making recordings. Check that the same type of video cable is used for connecting both the recorder and the video source (the one you want to record) to this receiver.
PAGE 127
SC-37_35_UXJCB.book 127 ページ２０１０年３月９日火曜日午前９時３２分 Additional information Symptom 13 Remedy The display shows KEY LOCK ON • With the receiver in standby, press  STANDBY/ON for about 10 seconds while holding down when you try to make settings. SPEAKERS to disable the key lock. Most recent settings have been • The power cord was disconnected from the wall while adjusting this setting. erased. • Settings are only stored if all the zones are turned off.
PAGE 128
12he_Additional_info.fm 13 128 ページ２０１０年３月９日火曜日午後１時９分 Additional information Remote control Symptom Remedy Cannot be remote controlled. • Set the remote control unit’s remote control mode so that it matches the setting on the main unit (see Operating multiple receivers on page 84 (SC-37)/page 96 (SC-35)). • Check whether the receiver’s remote control mode is properly set (see Remote Control Mode Setup on page 119).
PAGE 129
SC-37_35_UXJCB.book 129 ページ２０１０年３月９日火曜日午前９時３２分 Additional information 13 HDMI Symptom Remedy The HDMI indicator blinks continuously. • Check all the points below. No picture or sound. • This receiver is HDCP-compatible. Check that the components you are connecting are also HDCPcompatible. If they are not, please connect them using the component or composite video jacks.
PAGE 130
SC-37_35_UXJCB.book 13 130 ページ２０１０年３月９日火曜日午前９時３２分 Additional information Important information regarding the HDMI connection There are cases where you may not be able to route HDMI signals through this receiver (this depends on the HDMIequipped component you are connecting–check with the manufacturer for HDMI compatibility information). If you aren’t receiving HDMI signals properly through this receiver (from your component), please try one of the following configurations when connecting up.
PAGE 131
SC-37_35_UXJCB.book 131 ページ２０１０年３月９日火曜日午前９時３２分 Additional information Symptoms 13 Causes Remedies A USB memory device is Some formats of USB memory devices, including connected and displayed, but FAT 12, NTFS, and HFS, cannot be played back on the audio files stored on the this receiver. USB memory device cannot be played back. The file format cannot be properly played back on this receiver. Check whether the format of your USB memory device is either FAT 16 or FAT 32.
PAGE 132
SC-37_35_UXJCB.book 13 132 ページ２０１０年３月９日火曜日午前９時３２分 Additional information Status messages Cause Action Check Antenna The XM antenna is not connected to the XM MiniTuner Home Dock or the XM antenna cable is damaged. Check that the XM antenna is securely connected to the XM Mini-Tuner Home Dock and check the antenna cable for damage. Replace the XM antenna if the cable is damaged. Loading The XM Mini-Tuner is acquiring audio or program information from the XM satellite signal.
PAGE 133
SC-37_35_UXJCB.book 133 ページ２０１０年３月９日火曜日午前９時３２分 Additional information 13 Status messages Cause Action Check Sirius Tuner The SiriusConnect™ tuner is not properly connected. Check that the 8 pin mini DIN cable and AC Adapter are attached securely. Acquiring Signal The SIRIUS signal is too weak at the current location. Check for antenna obstructions and reposition the SIRIUS antenna to get better signal reception. Use the Antenna Aiming option to optimize the antenna position.
PAGE 134
SC-37_35_UXJCB.book 13 134 ページ２０１０年３月９日火曜日午前９時３２分 Additional information Symptoms Causes Remedies Cannot access the component connected to the network. The component connected to the network is not properly set. If the client is automatically authorized, you need to enter the corresponding information again. Check whether the connection status is set to “Do not authorize”. There are no playable audio files on the component connected to the network.
PAGE 135
SC-37_35_UXJCB.book 135 ページ２０１０年３月９日火曜日午前９時３２分 Additional information 13 Status messages Descriptions Item Already Exists This is displayed when the file you have attempted to register in the Favorites folder has already been registered. Favorite List Full This is displayed when you have attempted to register a file in the Favorites folder but the Favorites folder is already full.
PAGE 136
SC-37_35_UXJCB.book 136 ページ２０１０年３月９日火曜日午前９時３２分 Additional information 13 correcting the tonal and spatial errors that occur. On this product, when the THX indicator is on, THX features are automatically added in Cinema modes (e.g. THX Cinema, THX Surround EX).
PAGE 137
SC-37_35_UXJCB.book 137 ページ２０１０年３月９日火曜日午前９時３２分 Additional information 13 Record the SiriusConnect™ tuner ID below for reference. About iPod Record the XM Radio ID below for reference. Note: The XM Radio ID does not use the letters “I”, “O”, “S” or “F”. “Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards.
PAGE 138
SC-37_35_UXJCB.book 13 138 ページ２０１０年３月９日火曜日午前９時３２分 Additional information Auto Surround, ALC and Stream Direct with different input signal formats The following charts show what you will hear with different input signal formats, depending on the Stream Direct mode (see Using Stream Direct on page 62) you have selected.
PAGE 139
SC-37_35_UXJCB.book 139 ページ２０１０年３月９日火曜日午前９時３２分 Additional information 13 Preset code list (SC-35 only) You should have no problem controlling a component if you find the manufacturer in this list, but please note that there are cases where codes for the manufacturer in the list will not work for the model that you are using. There are also cases where only certain functions may be controllable after assigning the proper preset code.
PAGE 140
SC-37_35_UXJCB.
PAGE 141
SC-37_35_UXJCB.
PAGE 142
SC-37_35_UXJCB.
PAGE 143
SC-37_35_UXJCB.book 143 ページ２０１０年３月９日火曜日午前９時３２分 Additional information 13 Integrated Control Section Specifications Amplifier Section Continuous average power output of 140 watts* per channel, min., at 8 ohms, from 20 Hz to 20 000 Hz with no more than 0.08 %** total harmonic distortion. Multi channel simultaneous power output (1 kHz, 1 %, 8 Ω) 7 ch total . . . . . . . . . . . . . . . . 770 W (SC-37)/700 W (SC-35) Continuous Power Output (20 Hz to 20 kHz, 8 Ω, 0.08 %) Front. . . . . . . . . . . . .
PAGE 144
SC-37_35_UXJCB.book 13 144 ページ２０１０年３月９日火曜日午前９時３２分 Additional information Number of Furnished Parts Incase of SC-37: MCACC Setup microphone (APM7009) . . . . . . . . . . . . . . . . .1 Omni-directional remote control (CU-RF100) (AXD7580) . . . . . . . . . . . . . . . .1 RF adapter (AXX7272) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 IR blaster cable (ADF7007) . . . . . . . . . . . . . . . . . . . . . . . . . . .2 AA/LR6 dry cell batteries . . . . . . . . . . . . . . . . . . . .
PAGE 145
SC-37_35_UXJCB.book 145 ページ２０１０年３月９日火曜日午前９時３２分 Additional information 13 We Want You Listening For A Lifetime Selecting fine audio equipment such as the unit you’ve just purchased is only the start of your musical enjoyment. Now it’s time to consider how you can maximize the fun and excitement your equipment offers. This manufacturer and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level.
PAGE 146
SC-37_35_UXJCB.
PAGE 147
SC-37_35_UXJCB.
PAGE 148
SC-37_35_UXJCB.book 148 ページ２０１０年３月９日火曜日午前９時３２分 To register your product, find the nearest authorized service location, to purchase replacement parts, operating instructions, or accessories, please go to one of following URLs : Pour enregistrer votre produit, trouver le service après-vente agréé le plus proche et pour acheter des pièces de rechange, des modes d’emploi ou des accessoires, reportez-vous aux URL suivantes : In the USA/Aux Etats-Unis http://www.pioneerelectronics.