DJ MIXER DJM-707 Operating Instructions 1
Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference. In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory drawings. However the method of connecting and operating the unit is the same.
IMPORTANT NOTICE The serial number for this equipment is located on the bottom plate. Please write this serial number on your enclosed warranty card and keep it in a secure area. This is for your security. WARNING: Handling the cord on this product or cords associated with accessories sold with the product will expose you to lead, a chemical known to the State of California and other governmental entities to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
CHECKING ACCESSORIES ÷ Hexagonal Allen driver (for cross fader operating load adjust screw) These operating instructions Warranty ÷ ÷ FEATURES 1) Designed for high sound quality Electronic parts have been carefully selected and internal circuitry redesigned to provide the shortest-possible signal paths, thus realizing true club sound with power to spare.
CONNECTIONS When connecting or changing the connection of units, make sure to first turn off the power switch and disconnect the power cord from the outlet. This mixer is not furnished with any connection cables; when performing connections, use the cables that came provided with your player and other components, or purchase commercially available audio cables. 1.
CONNECTIONS 2. Connecting Headphones (front panel) Headphones FADER START FADER REVERSE CH-1 C.F. CH-2 C.F. 1 CH-1 ON ON ON OFF OFF OFF PHONES C.F. 2 CH-2 PROFESSIONAL 2CHANNEL MIXER 5 DJM-707 POWER FADER CURVE CH-1 CROSS FADER 1 CROSS FADER 2 CH-2 FADER CUT LAG MIN MAX Headphones 5 Use to connect headphones with a 6.3 mm diameter stereo plug. 3.
PART NAMES AND FUNCTIONS Top Panel 2 1 20 PHONO 1 /LINE 1 10 11 PHONO 2 /LINE 2 CD 1 CD 2 MIC LEVEL MASTER LEVEL TRIM TRIM 3 12 PROFESSIONAL 2CHANNEL MIXER – DJM-707 0 HI +9 – – BOOTH/SESSION OUT +9 – 13 HI HI POWER +12 -12 PHONES +6 -26 14 +6 -26 MID MID -12 0 – LOW 4 0 0 – +12 5 SELECT MIC SEND MASTER +6 -26 6 +6 -26 LOW LOW 16 SESSION IN CH-1 7 +6 -26 8 9 EQ OFF OFF ON ON TRANSFORM FADER START CH-2 SEND 17 18 19 FADER START TRANSFORM 21 22
PART NAMES AND FUNCTIONS 5 CH-1 equalizer dials (HI/MID/LOW) 16 CH-2 equalizer dials (HI/MID/LOW) HI Use to adjust CH-1 input treble response (range of adjustment: 13 kHz, +6 dB to –26 dB). MID Use to adjust CH-1 input midrange response (range of adjustment: 1 kHz, +6 dB to –26 dB). LOW Use to adjust CH-1 input bass response (range of adjustment: 70 Hz, +6 dB to –26 dB). HI Use to adjust CH-2 input treble response (range of adjustment: 13 kHz, +6 dB to –26 dB).
PART NAMES AND FUNCTIONS 24 CH-1 fader lever 34 MASTER LEVEL display button and indicator The CH-1 fader lever is used to control the level of signals sent to the cross fader. Signal level is maximum at scale mark “10,” and minimum at scale mark “0”. When the front panel CH-1 FADER REVERSE switch is set to [ON], the signal level is maximum at scale mark “0,” and minimum at scale mark “10”. * The channel fader curve can be adjusted by means of the front panel FADER CURVE dials.
PART NAMES AND FUNCTIONS Front Panel 38 39 FADER START FADER REVERSE CH-1 C.F. CH-2 C.F. 1 CH-1 ON ON ON OFF OFF OFF PHONES C.F.
PART NAMES AND FUNCTIONS Rear Panel 43 CH-2 R L 44 R 45 SEND L R 46 RETURN L CH-1 R L 47 MIC CD CD 57 R MASTER 2 (MONO) L PHONO / LINE (MONO) MASTER 1 PHONO 56 SIGNAL GND LINE 55 54 53 R 2 HOT 52 L 51 48 PHONO SIGNAL GND CH-2 PLAYER CONTROL BOOTH/ SESSION OUT L R PHONO / LINE 3 COLD 1 GND LINE CH-1 PLAYER CONTROL SESSION IN 50 49 43 CH-2 input jacks 50 CH-1 signal ground (SIGNAL GND) CD Connect to audio output from CH-2 CD player.
FADER OPERATIONS Adjusting Fader Lever Operating Sensation Fader reverse function Operating load adjust screw (FEELING ADJ.) The operating directions of the CH-1, CH-2 and cross fader levers can be reversed by setting the front panel’s FADER REVERSE switches to their [ON] positions.
FADER OPERATIONS Start playback with channel fader 1 To control a connected CD player, set the front panel FADER START selector switch for the corresponding channel to its [CH-1] or [CH-2] position. Start playback with cross fader 1 To control a connected CD player, set the front panel FADER START selector switch for the corresponding channel to its [C.F.1] or [C.F.2] position. When using the CH-1 fader lever to start the CH-1 CD player, set the front panel C.F.
TROUBLESHOOTING Incorrect operations are often mistaken for trouble and malfunctions. If you think there is something wrong with this component, check the points below. Sometimes the trouble may originate from another component. Thus, also check the other electrical appliances also in use. If the trouble cannot be rectified even after checking the following items, contact your dealer or nearest PIONEER service center. Problem Possible Cause Countermeasure The power does not turn on.
SPECIFICATIONS Audio Section Input terminal (input level/impedance) CD 1, 2 ....................................... –14 dBV (200 mV) / 22 kΩ LINE 1, 2 .................................... –14 dBV (200 mV) / 22 kΩ PHONO 1, 2 .................................. –54 dBV (2 mV) / 47 kΩ MIC .................................................. –54 dBV (2 mV) / 3 kΩ SESSION IN ............................... –14 dBV (200 mV) / 22 kΩ RETURN ....................................
Published by Pioneer Corporation. Copyright © 2003 Pioneer Corporation. All rights reserved. PIONEER CORPORATION PIONEER ELECTRONICS (USA) INC. Multimedia and Mass Storage Division: 2265 East 220th Street, Long Beach, CA 90810, U.S.A. TEL: 800-444-OPTI (6784) PIONEER ELECTRONICS OF CANADA, INC.
