User Manual

En
13
Connections and part names
1 OFF, ON, TALK OVER selector switch
Turns the microphone on/off.
2 USB connection indicator
Displays the connection status between the USB-A terminal and
USB-B terminal.
Lights: When communication with Serato DJ is normal
Flashes: When the computer is connected to the terminal and the
driver is not installed
Lights out: When the computer is not connected to the terminal
3 USB (A) button
When lights, the USB-A terminal is used in communication with the
computer.
!
The [USB (A)] button and [USB (B)] button located at the left
side are used to control the USB communication for deck 1 or
deck 3. The [USB (A)] button and [USB (B)] button located at the
right side are used to control USB communication for deck 2 or
deck 4.
! When the [USB (A)] button or [USB (B)] button located on the
left side is flashing, it means the deck 1 or deck 3 audio is on
air. Flashing stops when the channel fader of deck 1 or deck 3 is
moved to the frontmost position. When the [USB (A)] button or
[USB (B)] button located on the right side is flashing, it means
deck 2 or deck 4 audio is on air. Flashing stops when the chan-
nel fader of deck 2 or deck 4 is moved to the frontmost position.
(When the USB terminal is switched, sound is also switched
instantaneously. Therefore, when the button is flashing, before
switching the USB terminal, make sure that the deck is not used
by another user.)
4 USB (B) button
When lights, the USB-B terminal is used in communication with the
computer.
! The [USB (A)] button and [USB (B)] button located at the left
side are used to control the USB communication for deck 1 or
deck 3. The [USB (A)] button and [USB (B)] button located at the
right side are used to control USB communication for deck 2 or
deck 4.
! When the [USB (A)] button or [USB (B)] button located on the
left side is flashing, it means the deck 1 or deck 3 audio is on
air. Flashing stops when the channel fader of deck 1 or deck 3 is
moved to the frontmost position. When the [USB (A)] button or
[USB (B)] button located on the right side is flashing, it means
deck 2 or deck 4 audio is on air. Flashing stops when the chan-
nel fader of deck 2 or deck 4 is moved to the frontmost position.
(When the USB terminal is switched, sound is also switched
instantaneously. Therefore, when the button is flashing, before
switching the USB terminal, make sure that the deck is not used
by another user.)
5 MASTER LEVEL control
Adjusts the master sound level output.
6 MASTER CUE button
Turns monitoring of the master output’s sound on and off.
7 Master level indicator
Displays the master output’s audio level.
8 BOOTH MONITOR control
Adjusts the level of audio signals output from the [BOOTH] terminal.
9 MASTER OUT COLOR control
Changes the SOUND COLOR FX parameter applied to the master
output sound.
a OSCILLATOR SELECT buttons
Generates oscillator sound (NOISE, DROP, LASER, and SIREN).
= Using the oscillator function (p. 24 )
b OSCILLATOR VOLUME control
Adjusts the sound level of oscillator sound.
c OSCILLATOR PARAMETER control
Adjusts the quantitative parameters of oscillator sound.
d OSC ASSIGN selector switch
Selects the channel to output oscillator sound.
e HEADPHONES LEVEL control
Adjusts the sound level output from the headphones.
f HEADPHONES MIXING control
Adjusts the balance of the monitor volume between the sound of the
channels for which the headphones [CUE] button is pressed and the
sound of the master channel.
g SOUND COLOR FX buttons
These turn the SOUND COLOR FX effects on/off.
h MIC COLOR control
Changes the SOUND COLOR FX parameter applied to microphone
sound.
i SAMPLER VOL control
Adjusts the sound level of sampler.
j EQ (HI, LOW) controls
These adjust the tone quality of the [MIC1] and [MIC2] channels.
k MIC2 control
Adjusts the sound level output from the [MIC2] channel.
l MIC1 control
Adjusts the sound level output from the [MIC1] channel.
m LINE, PHONO, USB selector switch
Selects the input source of each channel from the components con-
nected to this unit.
! [LINE]: Select this to use a line level output device (DJ player,
etc.) connected to the [LINE] input terminals.
— When [PHONO] is selected, sound is muted momentarily.
! [PHONO]: Select this to use a phono level (for MM cartridges)
output device (analog player, etc.) connected to the [PHONO]
input terminals.
! [USB]: Select this to use the track loaded in the Serato DJ soft-
ware’s deck.
n CD, USB selector switch
Selects the input source of each channel from the components con-
nected to this unit.
! [CD]: Select this to use a line level output device (DJ player, etc.)
connected to the [CD] terminals.
! [USB]: Select this to use the track loaded in the Serato DJ soft-
ware’s deck.
o FX 1 assign button
Turns effect unit FX1 on and off for the respective channel.
p FX 2 assign button
Turns effect unit FX2 on and off for the respective channel.
q Channel Level Indicator
Displays the sound level of the respective channels before passing
through the channel faders.
r TRIM control
Adjusts the level of audio signals input in each channel.
s ISO (HI, MID, LOW) controls
Boosts or cuts frequencies for the different channels.
t COLOR control
This changes the parameters of the SOUND COLOR FX of the differ-
ent channels.
u Headphones CUE button
Press:
The sound of channels for which the headphones [CUE] button is
pressed is output to the headphones.
!
When the headphones [CUE] button is pressed again, monitoring
is canceled.
[SHIFT] + press:
The track’s tempo can be set by tapping the button. (Tap function)