User guide

If you upgrade your navigation system by
these discs, the system will have the following
changes.
Renewal data
The following data are updated:
! Map database
! Gracenote
®
Database
POI data coverage
Approximately 5.3 million POIs are included in
the database.
p For the modified categories that can be
used on “Overlay POI”, “Vicinity Search”
and used on the voice recognition, refer to
Category list for vicinity search (Renewal).
p Some POI information may not be accurate
or may become inaccurate through the
passage of time. Please directly contact the
POI to verify the accuracy of the informa-
tion about the POI which appears in this
database. POI information is subject to
change without notice.
Keyboard operation
Input screen of “Address Search” and
“POI Search”
Others, Sym., 0-9:
Touch to toggle the selection.
Input screen for “Address Book”, “Phone
Book”, “LIBRARY (Music Library)”
Others, 0-9:
Touch to toggle the selection.
Small, Caps.:
This is a new feature. Either lowercase or
uppercase letters can be selected. Touch to
toggle the selection.
Time restrictions
This is a new feature. This setting controls
whether streets or bridges have traffic restric-
tions during a certain time should be taken
into account.
p If you want to set your route to avoid raised
draw bridges, select “On”.
p Settings marked with an asterisk (*) show
that these are default or factory settings.
1 Touch the key in the following order in
the navigation menu.
[Destination] d [Route Overview] d [Op-
tions]
p “Route Overview” is active only when the
route is set.
2 Touch [Time restrictions] to change the
route calculation conditions.
<CRB3467-A>17
Renewed points through
this upgrade
Touching this option switches the setting “ On”
or “Off”.
On*:
Calculates a route while avoiding streets or
bridges with traffic restrictions during a cer-
tain time.
Off:
Calculates a route while ignoring traffic re-
strictions.
3 Touch [OK].
The route is recalculated, and the Route con-
firmation screen appears.
p The system may calculate a route that in-
cludes streets or bridges that are subject to
traffic restrictions during a certain time
even if “On” is selected.
CAUTION
If the time difference is not set correctly, the na-
vigation system cannot consider traffic regula-
tions correctly. Set the time difference correctly
(For details, refer to the Operation Man ual of
your navigation system.)
shows for routes that contain streets or bridges
that are subject to traffic regulations during a certain
time when the setting “Time restrictions” is “On”.
2D Twin Map View and 3D
Twin Map View
Either “2D Twin Map View” or “3D Twin
Map View” can directly be selected in “View
Mode Selection” screen.
1 Press the MAP button to display a map
of the area around your current position.
2 Press the MAP button again.
3 Touch the mode name to select the
mode you want to display.
2D Twin Map View
The 2D map appears on the left screen.
3D Twin Map View
The 3D map appears on the left screen.
p Touching anywhere on the map changes
the map to the Scroll mode.
Address Book Icon
You can select whether to display the icons for
the entries of “Address Book” on the map.
p When you select “Address Book Icon Dis-
play” in “Short-Cut Selection”, you can
switch this setting with the shortcut menu.
p Settings marked with an asterisk (*) show
that these are default or factory settings.
<CRB3467-A>18
1 Touch the key in the following order in
the navigation menu.
[Map] d [Displayed Info]
2 Touch [Address Book Icon].
Each time you touch the key changes that set-
ting.
! On*:
Displays the icon on the map.
! Off:
Hides the icon from the map.
p Even if “Address Book Icon” is set to
“Off”, the alarm sounds when you ap-
proach the registered location and the
set image pops up. To turn off the sound
output and image pop up, select
“No Sound” and “No Picture” for the
entry.
p If you set
(dot), the registered name
of that entry can be displayed on the
map. The registered name does not ap-
pear if “Address Book Icon” is set to
“Off”.
3D Landmark
You can select whether to display the 3D land-
mark on the map.
p 3D landmark only appears when the view
mode is “3D Twin Map View” and the
map scale is set to 200 m (0.25 mile) or
lower.
p Settings marked with an asterisk (*) show
that these are default or factory settings.
1 Touch the key in the following order in
the navigation menu.
[Map] d [Displayed Info]
2 Touch [3D Landmark].
Each time you touch the key changes that set-
ting.
! On*:
Displays the 3D landmark on the map.
! Off:
Hides the 3D landmark on the map.
Traffic event icon and line
p Middle-sized icon is displayed on the map
scale between 2 km to 5 km (1 mile to
2.5 miles).
p The traffic-related items can be shown on
the detailed city map.
Hands-free phoning
Device name
The default device name displayed on the mo-
bile phone changes “PIONEER NAVI” to
“PIONEER HDD NAVI”. (If you already con-
nected the Bluetooth unit, the name already
set remains. If you restore the default setting,
the device name becomes “PIONEER HDD
NAVI”.)
The display of an unknown user’s call
Depending on the caller ID service, the phone
number of the received call may not be dis-
played. [Unknown] appears instead in that
case.
<CRB3467-A>19
Editing the entry in “Phone Book”
The default device name displayed on the mo-
bile phone changes “PIONEER NAVI” to
“PIONEER HDD NAVI”. (If you already con-
nected the Bluetooth unit, the name already
set remains. If you restore the default setting,
the device name becomes “PIONEER HDD
NAVI”.)
Editing the entry in “Phone Book”
You can edit [ Pronunciation] to be used for
voice recognition along with [Name], [Phone
#], or [Picture].
1 Touch [Info/Phone] in the Navigation
menu, and touch [Phone Menu].
2 Touch [Phone Book].
3 Touch
or [Add].
The edit screen appears.
1 Name
Enter the name to be displayed in the
phone book. If you enter the name for new
entry, you can select whether you use this
entry as voice commands.
2 Pronunciation
You can enter the desired pronunciation in-
dependently from the name. The registered
pronunciation is used for voice recognition.
p Up to 40 characters can be input for the
pronunciation.
p If “Pronunciation” is blank, you cannot
use the item as a voice command.
p Depending on which language is being
switched to, you may not be able to use
the registered pronunciation without
modification.
3 Phone #
These operations are the same as before
upgrade.
4 Picture
These operations are the same as before
upgrade.
Changing a name
1 Touch [Name], then touch [Yes].
The message confirming whether or not to
register the entered name as voice command
is displayed.
When not registering a name as a voice com-
mand, select [No].
2 Enter a new name, then touch [OK].
The current name appears in the text box.
3 If the pronunciation is suitable, touch
[Yes].
The details you set are registered, and “Phone
Book Record Edit” screen appears.
Alternative options:
No:
Completes the registration without editing the
pronunciation.
Repeat:
You can reconfirm the pronunciation of the
name you entered.
No sounds can be output during .
<CRB3467-A>20