User guide

07
58
En
No picture is displayed or the
picture is not displayed
properly.
Is the video cable properly
connected?
• Connect the cable properly according to the connected devices
(page 14).
• Insert the cable firmly and all the way in.
Is the video cable damaged? If the cable is damaged, replace it with a new one.
Is the input setting on the
connected TV or AV receiver
or amplifier right?
Read the operating instructions of the connected components and
switch to the proper input.
Are you viewing the picture
from the video output
terminal selected with VIDEO
SELECT?
Press VIDEO SELECT to switch the video output terminal to be viewed
(page 22).
Is the output video resolution
properly set?
Use OUTPUT RESOLUTION to switch to a resolution at which the video
and audio signals are output (page 22).
• Is the player connected
with an HDMI cable other
than a High Speed HDMI™
cable (with a Standard
HDMI™ cable)?
• Are you using an HDMI
cable with built-in equalizer?
1080p or Deep Color video signals may not be output properly,
depending on the HDMI cable being used or the player’s settings.
Press  while pressing  on the player’s front panel to restore the
video outputs to the factory default settings. After this, if you wish to
output the video signals with 1080p or Deep Color, connect the TV
using a High Speed HDMI™ cable without built-in equalizer, then reset
the player using the Setup Navigator (page 19).
Is a DVI device connected? The picture may not be displayed properly if a DVI device is connected.
Is HDMI Color Space
properly set?
Change the HDMI Color Space setting (page 39).
Picture freezes and the front
panel and remote control
buttons stop working.
• Press  STOP to stop playback, then restart playback.
• If the playback cannot be stopped, press  STANDBY/ON on the
player’s front panel to turn off the power, then turn the power back on.
• If the power cannot be turned off, press and hold  STANDBY/ON
on the player’s front panel for over 5 seconds. The power will turn off.
Motion is unnatural or
picture is not clear.
Change the Pure Cinema setting (page 34).
No picture is displayed or
picture is not output in high
definition when playing BDs.
With some discs, it may not be possible to output the video signals from
the VIDEO output terminal or the COMPONENT VIDEO output
terminals. In this case, connect using an HDMI cable (page 14).
• Picture is disturbed during
playback.
• Picture is dark.
• This player supports Macrovision analog copy protection technology.
With some TVs (such as with built-in video deck), the picture will not be
displayed properly when the copy protected DVD title is played. This is
not a malfunction.
• If the player and TV are connected via a DVD recorder/video deck,
etc., the picture will not be displayed properly due to analog copy
protection. Connect the player and TV directly.
• Picture is stretched.
• Picture is cropped.
• Aspect ratio cannot be
switche
d.
Is the TV’s aspect ratio
properly set?
Read the TV’s operating instructions and set the TV’s aspect ratio
properly.
Is TV Aspect Ratio properly
set?
Set TV Aspect Ratio properly (page 37).
Is 4:3 Video Out properly
set?
Set 4:3 Video Out properly (page 37).
Is DVD 16:9 Video Out
properly set?
Set DVD 16:9 Video Out properly (page 37).
When video signals with a resolution of 1080/24p, 1080/60i, 1080/60p or
720/60p are being output from the HDMI OUT terminal or the
COMPONENT VIDEO output terminals, they may be output with an
aspect ratio of 16:9 even if TV Aspect Ratio is set to 4:3 (Standard)
(page 37).
Picture is interrupted. The picture may be interrupted when the resolution of the recorded
video signal switches. Press OUTPUT RESOLUTION to select a setting
other than Auto or Source Direct (page 22).
The subtitles cannot be
switched.
The subtitles cannot be switched for discs recorded on a DVD or BD
recorder.
Problem Check Remedy
320_UXJCA_EN.book 58 ページ ２００９年２月１３日 金曜日 午後４時２６分