User manual

GG
#HROK@XHMFÐSGDÐÆQLV@QDÐ
version
1 Display the “)OJ<76” setting screen.
 Refer to Displaying the “)OJ<76” setting screen on page
52
2 Touch [)OJ<76($9PB863<LB9].
3 Touch [DL86C387($9PB863<LB9].
Displaying&the&open&source&
licences
You can check the open source licenses of the functions that this
product is equipped with.
1 Display the “)OJ<76” setting screen.
 Refer to Displaying the “)OJ<76” setting screen on page
52
2 Touch [)OJ<76($9PB863<LB9].
3 Touch [DL86C387($9PB863<LB9].
4 Touch [?L47947].
4OC@SHMFÐÆQLV@QD
CAUTION
 The external storage device for updating must contain only
the correct update file.

Never turn this product off, disconnect the USB storage
device while the firmware is being updated.

You can only update the firmware when the vehicle is
stopped and the handbrake is engaged.
1 Download the firmware update files into your
computer.
2 Connect a blank (formatted) storage device
to your computer, and then locate the correct
update file and copy it onto the storage device.
3 Set the external storage device to this product.
 Refer to Plugging and unplugging a USB storage device on
page 5
4 Turn the source off.
 Refer to Selecting a source on page 7
5 Display the “)OJ<76” setting screen.
 Refer to Displaying the “)OJ<76” setting screen on page
52
6 Touch [)OJ<76($9PB863<LB9].
7 Touch [DL86C387(/:>3<7].
8 Touch [0B9<L9;7] to display the data transfer
mode.
Follow the on-screen instructions to finish updating the
firmware.
p
If an error message appears on the screen, touch the display
and perform the above steps again.
Checking&sensor&learning&status&
and&driving&status
You can check the sensor learning status, such as the degree of
learning. You can also check the current sensor values and the
total number of speed pulses.
1 Display the “)OJ<76” setting screen.
 Refer to Displaying the “)OJ<76” setting screen on page
52
2 Touch [)OJ<76($9PB863<LB9].
3 Touch [[E(03FLR83<LB9()<3<;J].
Clearing&the&status
You can delete the learned results stored in the sensor.
1 Display the “[E(03FLR83<LB9()<3<;J” screen.
2 Touch [ELJ<3947] or [):77>(1;FJ7], and then
touch [*7J].
3 Touch [?7389L9G] and then touch [-7J7<("FF].
p To uc h [-7J7<("FF] to reset the sensor after changing the
installation position or angle.
p
If you touch [-7J7<(ELJ<3947], all learned results stored in
“ELJ<3947” are cleared.
Checking&the&connections&of&
leads
Check that the leads are properly connected between this
product and vehicle.
1 Display the “)OJ<76” setting screen.
 Refer to Displaying the “)OJ<76” setting screen on page
52
2 Touch [)OJ<76($9PB863<LB9].
3 Touch [0B9974<LB9()<3<;J].
 %1)("9<7993
Displays the connection status of the GPS aerial (“'K” or
“!'K”) and the reception sensitivity.
p
If reception is poor, please change the installation position
of the GPS aerial.

1BJL<LB9L9G()<3<;J
Displays the positioning status (3D positioning, 2D posi-
tioning, or no positioning), the number of satellites used for
positioning (orange), and the number of satellites whose
signal has been received (yellow). If signals from more than
three satellites are received, the current location can be
measured.

Refer to Positioning technology on page 67

$9J<3FF3<LB9
Indicates whether the installation position of this product
is correct or not. If installed correctly, “'K” appears. When
this product is installed at an extreme angle exceeding
the limitation of the installing angle, “!'K]$9J<Q("9GF7^”
will be displayed. If the installation of this product is
continually changed and it is not firmly fixed into place,
“!'K]#LR83<LB9^” will be displayed.

):77>(1;FJ7
The speed pulse value detected by this product is shown.

$FF;6L93<LB9
Displays the status of headlights or small lamps of the
vehicle.

2345()LG93F
When the gearstick is shifted to “R” (reverse position), the
signal switches to “.LGH” or “?BC”. The signal displayed will
vary depending on the vehicle.

#7HL4F7(">3:<78
Displays the status of the vehicle adapter.

E#E(E8LN7(':<LB9
Displays the status of the optional DVD player.
!"#$%&''()*"+
System5settings