User manual

GT
p
When the screen changes to full-screen rear view camera
image during normal driving, switch to the opposite setting
in “-7N78J7(%738()7<<L9GQ”.
p
If you touch while the camera image is displayed, the
displayed image will turn off temporarily.
Setting&rear&view&camera&activation
The default setting is “'PP”.
1 Display the “)OJ<76” setting screen.
 Refer to Displaying the “)OJ<76” setting screen on page
52
2 Touch [036783(J7<<L9GJ].
3 Touch [2345(036783($9:;<] to switch “'9” or
“'PP”.
Setti ng&the&polarity&of&the&rear&view&
camera
The default setting is “23<<78O”.
1 Display the “)OJ<76” setting screen.
 Refer to Displaying the “)OJ<76” setting screen on page
52
2 Touch [036783(J7<<L9GJ].
3 Touch [-7N78J7(%738()7<<L9GQ].
 23<<78O:
The polarity of the connected lead is positive.

%8B;9>:
The polarity of the connected lead is negative.
Setti ng&the&reversed&image&display&
for&the&rear&view&image
You can set whether to reverse the rear view camera images to
be displayed on the front screen.
The default setting is “'PP”.
p
This setting is available only when you stop your vehicle in a
safe place and apply the handbrake.
p
This function is available when “2345(036783($9:;<” is set
to “'9”.

Refer to Setting rear view camera activation on page 53
1 Display the “)OJ<76” setting screen.
 Refer to Displaying the “)OJ<76” setting screen on page
52
2 Touch [036783(J7<<L9GJ].
3 Touch [2345(036783X(-7N78J7(#L>7B] to switch
“'9” or “'PP”.
Setting&the&parking&assist&guidelines
Displ aying&the&parking&assist&
guidelines
You can set whether to display the parking assist guidelines on
the rear view camera images when backing up your vehicle.
The default setting is “'PP”.
1 Display the “)OJ<76” setting screen.
 Refer to Displaying the “)OJ<76” setting screen on page
52
2 Touch [036783(J7<<L9GJ].
3 Touch [1385L9G("JJLJ<(%;L>7] to switch “'9” or
“'PP”.
Adjus ting&the&parking&assist&
guidelines
CAUTION
 When adjusting the guidelines, be sure to park the vehicle
in a safe place and apply the handbrake.

Before getting out of the car to place the markings, be sure
to turn the ignition switch off (ACC OFF).

The range projected by the rear view camera is limited.
Also, the vehicle width and distance guidelines displayed
on the rear view camera image may differ from the actual
vehicle width and distance. (The guidelines are straight
lines.)

The image quality may deteriorate depending on the usage
environment, such as at night or in dark surroundings.
1 Park your vehicle in a safe place and apply the
handbrake.
2 Using packing tape or similar, place markings
as follows.
Rear bumper
25 cm
25 cm
50 cm
2 m
Markings
Markings
3 Display the “)OJ<76” setting screen.
 Refer to Displaying the “)OJ<76” setting screen on page
52
4 Touch [036783(J7<<L9GJ].
5 Touch [1385L9G("JJLJ<(%;L>7(">h;J<].
6 Set the guidelines by dragging the four points.
Adjust the guidelines so that the guidelines can be overlaid to
the markings
p
To uc h / / / / / to adjust the guidelines if
necessary. Touch [E7P3;F<] to reset the settings.
Setting&the&camera&for&Camera&
View&mode
To disp la y Ca me ra Vi ew at all time s, “ 036783(#L7C” needs to be
set to “'9”. (The same mode is turned on when
is touched
on the camera view screen. The setting value is synchronized.)
The default setting is “'PP”.
p
To set the rear view camera as the camera for Camera View
mode, set “2345(036783($9:;<” to “'9”.

Refer to Setting rear view camera activation on page 53
1 Display the “)OJ<76” setting screen.
 Refer to Displaying the “)OJ<76” setting screen on page
52
2 Touch [036783(J7<<L9GJ].
3 Touch [036783(#L7C] to switch “'9” or “'PP”.
p You can also turn this function on by touching [036783(
#L7C] on the AV source selection screen or in the source
list.
!"#$%&''()*"+
System5settings