Operation Manual

34
1 Display the “System” setting screen.
Refer to Displaying the “System” setting screen on page
33
2 Touch [Beep Tone] to switch “On” or “Off”.
Setting the auto audio mix
function
You can select whether or not to activate the auto audio mix
function. If the auto audio mix function is activated, this prod-
uct automatically switches between mixing or not mixing the
AV source sound and the sound output from your iPhone or
smartphone according to the mixing property, such as that of the
mixed sound or solo sound of the foreground application on your
iPhone or smartphone.
The default setting is “On”.
1 Display the “System” setting screen.
Refer to Displaying the “System” setting screen on page
33
2 Touch [Auto Mix] to switch “On” or “Off”.
Setting AppRadioMode Sound
You can set where the sound for AppRadioMode is output when
it is used with an Android device.
1 Display the “System” setting screen.
Refer to Displaying the “System” setting screen on page
33
2 Touch [Input/Output settings].
3 Touch [AppRadioMode Sound].
4 Touch the following settings.
AVH (default):
The sound is output from the speakers of this unit.
Smartphone
The sound is output from the speakers of the Android device.
p
With an iPhone, the sound is always output from the speak-
ers of this unit.
Setting the rear view camera
A separately sold rear view camera (e.g. ND-BC8) is required
for utilising the rear view camera function. (For details, consult
your dealer.)
Rear view camera
This product features a function that automatically switches to
the full-screen image of the rear view camera installed on your
vehicle, when the gearstick is in the REVERSE (R) position.
Camera View mode also allows you to check what is behind you
while driving.
Camera for Camera View mode
Camera View can be displayed at all times. Please note that
with this setting, the camera image is not resized to fit, and that
a portion of what is seen by the camera is not viewable.
To display the camera image, touch [Camera View] on the “AV
source selection” screen.
Refer to Source on the AV source selection screen on page
11
p
To set the rear view camera as the camera for Camera View
mode, set “Back Camera Input” to “On”.
Refer to Setting rear view camera activation on page 34
p
When using the 2nd camera, set “AV Input” to “Camera”.
Refer to Starting procedure (for camera) on page 32
p
When the camera view of both the rear view camera and 2nd
camera are available, the key to switch the display appears.
Touch this key to switch the display between the rear view
image and 2nd camera image.
CAUTION
Pioneer recommends the use of a camera which outputs
mirror reversed images, otherwise the screen image may
appear reversed.
p
Immediately verify whether the display changes to a
rear view camera image when the gearstick is moved to
REVERSE (R) from another position.
p
When the screen changes to full-screen rear view camera
image during normal driving, switch to the opposite setting
in “Camera Polarity”.
p
If you touch while the camera image is displayed, the
displayed image will turn off temporarily.
Setting rear view camera activation
The default setting is “Off”.
1 Display the “System” setting screen.
Refer to Displaying the “System” setting screen on page
33
2 Touch [Camera settings].
3 Touch [Back Camera Input] to switch “On” or
Off”.
Setting the polarity of the rear view
camera
p This function is available when “Back Camera Input” is
On”.
Refer to Setting rear view camera activation on page 34
1 Display the “System” setting screen.
Refer to Displaying the “System” setting screen on page
33
2 Touch [Camera settings].
3 Touch [Camera Polarity].
Battery (default):
The polarity of the connected lead is positive.
Ground:
The polarity of the connected lead is negative.
Setting the safe mode
You can set the safe mode that regulate operating some func-
tions only when you stop your vehicle in a safe place and apply
the handbrake.
The default setting is “On”.
1 Display the “System” setting screen.
Refer to Displaying the “System” setting screen on page
33
2 Touch [Safe Mode] to switch “On” or “Off”.
Setting the demo mode
The default setting is “On”.
1 Display the “System” setting screen.
Refer to Displaying the “System” setting screen on page
33
2 Touch [Demo Mode] to switch “On” or “Off”.
Selecting the system language
If the embedded language and the selected language setting
are not the same, text information may not display properly.
Some characters may not be displayed properly.
1 Display the “System” setting screen.
Refer to Displaying the “System” setting screen on page
33
2 Touch [System Language].
< CRB4706-B >
System settings