Other Manual

Connecting the units
When connecting with a rear view camera
When this product is used with a rear view camera, it is possible to automatically switch
from the video to rear view image when the gear shift is moved to REVERSE (R).
WARNING
USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE MAY
RESULT IN INJURY OR DAMAGE.
CAUTION
• The screen image may appear reversed.
• The rear view camera function is to be used as an aid for backing into a tight parking spot.
Do not use this function for entertainment purposes.
• Objects in the rear view may appear closer or more distant than they actually are.
You must use a camera
which outputs mirror
reversed images.
CAUTION
RCA cable
(sold separately)
To video output
Rear view camera
Rear view camera input
This product
Violet/white
Of the two lead wires connected to the back lamp, connect the one
in which the voltage changes when the gear shift is in the
REVERSE (R) position. This connection enables the unit to
sense whether the car is moving forwards or backwards.
15 cm (5-7/8 in.)
Fuse resistor
Connection method
1. Clamp the lead.
2. Clamp firmly with
needle-nosed pliers.
Note:
· It is necessary to set CAMERA POLARITY properly in SYSTEM MENU when
connecting the rear view camera.
Connecting the units
When connecting with a multi-channel processor
Multi-channel processor
(e.g., DEQ-P8000)
(sold separately)
Black
Black
When you connect a separately sold
DVD player to the separetely sold
multi-channel processor, the optical
cable from DVD player must be
connected to the optical cable 2 input
(OPT. IN2) of the multi-channel
processor.
DVD player (e.g., XDV-P6)
(sold separately)
Optical output
(Black)
This product
IP-BUS cable (supplied with
multi-channel processor)
Black
Blue
Blue
IP-BUS cable
(supplied with DVD player)
Optical cable
(sold separately)
RCA cable (supplied with
multi-channel processor)
RCA cable
(supplied with DVD player)
Optical cable
(supplied with
multi-channel processor)
Blue
IP-BUS input
(Blue)
Black
Multi-CD player
(sold separately)
IP-BUS cable
Black
Black
Blue
You can use only one video component
with this unit.
To RL
To RR
Connecting the units
When connecting the external video component and the display
External video
component (sold
separately)
Audio input
Display with RCA
input jacks (sold
separately)
To video input
To video output
To audio outputs
Video input
This product
Rear monitor output
RCA cables (sold separately)
• It is necessary to set AV INPUT to VIDEO in SYSTEM MENU when connecting the external
video component.
• It is necessary to set AV INPUT to S-DVD in SYSTEM MENU when connecting a multi-DVD
player.
When using a display connected to rear video output
This product’s rear video output is for connection of a display to enable passengers in the
rear seats to watch the DVD or Video CD.
WARNING
NEVER install the display in a location that enables the Driver to watch the DVD or
Video CD while driving.
Installation
Note
• Check all connections and systems before final
installation.
• Do not use unauthorized parts. The use of
unauthorized parts may cause malfunctions.
• Consult with your dealer if installation requires
drilling of holes or other modifications of the
vehicle.
• Do not install this unit where:
— it may interfere with operation of the vehicle.
— it may cause injury to a passenger as a result
of a sudden stop.
• Do not install the display where it may (i) obstruct
the driver’s vision, (ii) impair the performance of
any of the vehicle’s operating systems or safety
features, including air bags, hazard lamp buttons
or (iii) impair the driver’s ability to safely operate
the vehicle.
• The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places
such as near the heater outlet.
• Optimum performance is obtained when the unit
is installed at an angle of less than 30°.
• To some types of vehicles, this unit cannot be
properly installed. In such case, use the optional
installation kit (ADT-VA133).
Installation using the screw
holes on the side of the unit
Fastening the unit to the factory
radio-mounting bracket.
Position the unit so that its screw holes are
aligned with the screw holes of the bracket,
and tighten the screws at 3 or 4 locations on
each side.
Note
In some types of vehicles, discrepancy may
occur between the unit and the dashboard. If this
happens, use the supplied frame to fill the gap.
Factory radio
mounting bracket
If the pawl gets in the way,
bend it down.
Dashboard or console
Binding screw or
flush surface screw
Be sure to use the
screws supplied
with this unit.