Product Manual

FORM NTA-1002 / Rev. 1-20
Page 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS:
1. Screw the (2) threaded Post Base Sections (B & C)
together (see Fig. 1).
2. Use a post hole digger to make a hole a minimum of
12" in diameter x 36" deep. Fill the hole with concrete
(see Fig. 2).
Note: Local soil conditions may require a larger
footing. Check local codes.
3. Take the end of the assembled Post Base that has the (2)
5/16" dia. holes in it and place the opposite end into the
concrete (see Fig. 2). Install the Post 26" above ground
level and plumb vertically. Allow the concrete to cure
before installing the Grill on the Base.
4. Install the Grill (A) on the Post Base by placing the 3-1/2"
dia. Holes in the Swivel Mechanism of the Grill Firebox
over the end of the Post (see Fig. 2). Line up the (2) 5/16"
dia. Holes on the front and back of the Grill Swivel
Mechanism with the (2) 5/16" dia. Holes at the top of
the Post Base.
Insert the 6" Locking Pin (E) (included in the package
with the Cover Strut, Vent Covers, Bottom Grate
Hook, and fasteners) through the aligned holes leaving
an equal length of Pin protruding from each side of the
Swivel Mechanism (see Fig. 3).
Rotate the Grill one complete revolution (see Fig. 3).
The Locking Pin (E) will be bent and drawn into the
Swivel Mechanism to lock the Grill onto the Post Base.
5. Use the Cover Handle to open the Cover of the Grill (A) all the way
back (see Fig. 4). Slide the Cover Strut (D) over the Grate Handle on
the Firebox half of the Grill through the large hole in the middle of
the Strut at the end of the slot. Slide the Strut (D)
Fig. 1
B
C
Provided for Each EC-26 B2X2 COVERED PARK GRILL
A) (1) Covered Grill
B) (1) 21" long Model B2X2 Post Base Section with internally
threaded end and Locking Pin Holes
C) (1) 21" long Model B2X2 Post Base Section with externally
threaded end
D) (1) Cover Strut
E) (1) 6" Locking Pin to secure the Grill to the Post Base
F) (4) Vent Covers with adjusting handles
G) (1) Utility Shelf
H) (1) Bottom Grate Hook
(8) 3/8" x 3/4" Zinc Plated Carriage Bolts and
“2-way” Lock Nuts
A
MIN 12'' DIA x 36'' DEEP
CONCRETE FOOTING
RECOMMENDED
26''
B
NOTE:
LOCAL CONDITIONS
MAY REQUIRE
LARGER FOOTING.
CHECK LOCAL CODES.
PLUMB POST VERTICALLY
Fig. 2
SWIVEL MECHANISM
OF THE GRILL
FIREBOX (A)
(15-1/4'')
LOCKING
PIN HOLE IN
THE TOP OF
THE POST
BASE, (2)
C
LOCKING PIN HOLE
IN THE SWIVEL
MECHANISM, (2)
NORTHERN
TOOL + EQUIPMENT
ITEM 23579
SWIVEL
MECHANISM
OF THE
FIREBOX (A)
ROTATE FIREBOX (1) COMPLETE REVOL UTION
HOLE THROUGH
THE SWIVEL
MECHANISM FOR
THE LOCKING PIN (E)
Fig. 3
A
E
A
Fig. 4
3/8" x 3/4"
ZINC PLATED
CARRIAGE
BOLT, TYP
3/8" 2-WAY HEX
LOCK NUT, TYP
GRATE HANDLE
OF THE GRILL (A)
COVER OF
THE GRILL (A)
FIREBOX OF
THE GRILL (A)
LARGE HOLE
IN THE COVER
STRUT (D)
COVER HANDLE
OF THE GRILL (A)
D
DO NOT DISCARD!
– IMPORTANT INFORMATION –
Assembly and Installation
Instructions for
EC-26/S B2X2
COVERED PARK GRILLS
continued...