User manual

Programming with the PicoScope 6000 Series92
Copyright © 2009-2013 Pico Technology Ltd. All rights reserved.ps6000pg.en r9
4D PICO_SIGGEN_WAVEFORM_SETUP_FAILED - A problem occurred in
ps6000SetSigGenBuiltIn or ps6000SetSigGenArbitrary.
4E PICO_FPGA_FAIL
4F PICO_POWER_MANAGER
50 PICO_INVALID_ANALOGUE_OFFSET - An impossible analogue offset value was
specified in ps6000SetChannel.
51 PICO_PLL_LOCK_FAILED - Unable to configure the PicoScope 6000.
52 PICO_ANALOG_BOARD - The oscilloscope's analog board is not detected, or is
not connected to the digital board.
53 PICO_CONFIG_FAIL_AWG - Unable to configure the signal generator.
54 PICO_INITIALISE_FPGA - The FPGA cannot be initialized, so unit cannot be
opened.
56 PICO_EXTERNAL_FREQUENCY_INVALID - The frequency for the external clock is
not within ±5% of the stated value.
57 PICO_CLOCK_CHANGE_ERROR - The FPGA could not lock the clock signal.
58 PICO_TRIGGER_AND_EXTERNAL_CLOCK_CLASH - You are trying to configure the
AUX input as both a trigger and a reference clock.
59 PICO_PWQ_AND_EXTERNAL_CLOCK_CLASH - You are trying to configure the AUX
input as both a pulse width qualifier and a reference clock.
5A PICO_UNABLE_TO_OPEN_SCALING_FILE - The scaling file set can not be
opened.
5B PICO_MEMORY_CLOCK_FREQUENCY - The frequency of the memory is reporting
incorrectly.
5C PICO_I2C_NOT_RESPONDING - The I2C that is being actioned is not responding
to requests.
5D PICO_NO_CAPTURES_AVAILABLE - There are no captures available and
therefore no data can be returned.
5E PICO_NOT_USED_IN_THIS_CAPTURE_MODE - The capture mode the device is
currently running in does not support the current request.
103 PICO_GET_DATA_ACTIVE - Reserved
104 PICO_IP_NETWORKED - The device is currently connected via the IP Network
socket and thus the call made is not supported.
105 PICO_INVALID_IP_ADDRESS - An IP address that is not correct has been
passed to the driver.
106 PICO_IPSOCKET_FAILED - The IP socket has failed.
107 PICO_IPSOCKET_TIMEDOUT - The IP socket has timed out.
108 PICO_SETTINGS_FAILED - The settings requested have failed to be set.
109 PICO_NETWORK_FAILED - The network connection has failed.
10A PICO_WS2_32_DLL_NOT_LOADED - Unable to load the WS2 dll.
10B PICO_INVALID_IP_PORT - The IP port is invalid.
10C PICO_COUPLING_NOT_SUPPORTED - The type of coupling requested is not
supported on the opened device.
10D PICO_BANDWIDTH_NOT_SUPPORTED - Bandwidth limit is not supported on the
opened device.
10E PICO_INVALID_BANDWIDTH - The value requested for the bandwidth limit is out
of range.
10F PICO_AWG_NOT_SUPPORTED - The device does not have an arbitrary waveform
generator.
110 PICO_ETS_NOT_RUNNING - Data has been requested with ETS mode set but run
block has not been called, or stop has been called.
111 PICO_SIG_GEN_WHITENOISE_NOT_SUPPORTED - White noise is not supported on
the opened device.
112 PICO_SIG_GEN_WAVETYPE_NOT_SUPPORTED - The wave type requested is not
supported by the opened device.
116 PICO_SIG_GEN_PRBS_NOT_SUPPORTED - Siggen does not generate pseudo-
random bit stream.