PIDA Pro Series OUTP FORW ARUT D X M D O PIDA-5 PIDA-7 50 PIDA-1 000 50 O W A R D F PA T H LPF R E T U R N LPF FA 0dB TE-3 ST : PA T H L E LISTED 69N0 E97199 I/P: AC120V 60Hz MODEL NO: D12-10-03 O/P: 24V 1250mA HPF GAIN X T A A HPF EQ FA INPU FOW ARDT 0dB TE-3 ST RETU PA TH RN A L M HON-KWANG AHEAD PLUG IN CLASS 2 TRANSFORMER AC ADAPTOR U Model: MW57-02401250A ® L WO-W ISTR IBUT AY B ION AROA MPLDIF BAN IERD A ID P F GAIN M GAAT FAC IN TE NTIO & SL TO RY FOWTO MIN IMU SEOP T
SAFEGUARDS Important Information Product Inspection Inspect the equipment for shipping damage. Should any damage be discovered, immediately file a claim with the carrier. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE Important Safety Instructions To insure proper installation and operation, take a moment to read this guide before proceeding with the installation.
SAFEGUARDS Important Information EXAMPLE OF ANTENNA GROUNDING ACCORDING TO 10. Grounding or Polarization - This video product is equipped with either a three prong plug for 120 Vac use. It is to be inserted into only the type of receptacle for which they specifically designed . Do not cut off the round grounding pin in order to be able to fit into a two prong receptacle as this could cause injury and will void the warranty. 11.
DESCRIPTIONS and Specifications Features • + • • + • • • + • Several models available in 1000, 750 and 550MHz bandwidths Built-in variable slope and gain controls for foward path Built-in gain control for reverse path Optional plug-in equalizers and attenuators Dual push-pull hybrid modules for low distortion, high input and output capability External U.L approved 26Vac power supply Input and output test ports for monitoring signal levels without disturbing service.
DESCRIPTIONS PCB Plug-In Module and Jumper Locations RETURN PATH INPUT FOWARD PATH OUTPUT -30dB OUTPUT TEST POINT GAIN CONTROL (RETURN PATH) REMOVE JUMPERS W6 AND W5 AND INSERT JUMPER BETWEEN THESE TWO POINTS FOR PASSIVE RETURN PATH JUMPERS W5 AND W6 INSERTED FOR ACTIVE RETURN PATH W5 SLOPE CONTROL (FOWARD PATH) W10 W6 EQUALIZER W3 PLUG-IN LOCATION FOR ATTENUATOR* (RETURN PATH) PIDA 550/750/1000 W8 GAIN CONTROL (FOWARD PATH) W2 FOWARD ATTENUATOR PLUG-IN LOCATION FOR ATTENUATOR* (FORWARD PATH)
DESCRIPTIONS Block Diagram RF OUTPUT RETURN PATH INPUT TEST PORT (-30dB) HYBRID AMP 2 ATT. 49 MHz 36 MHz HPF LPF FLAT SLOPE CONTROL CIRCUIT FULL GAIN CONTROL CIRCUIT P4 GAIN CONTROL CIRCUIT HYBRID AMP 1 PASSIVE RETURN FULL J2 P3 J3 FREQUENCY OFFSETS - FCC (U.S.A.) P2 J1 W3 P1 W8 W2 49 MHz 36 MHz HPF LPF ATT. RF INPUT TEST PORT RETURN PATH OUTPUT (-30dB) NOTES: 1. FOR PASSIVE RETURN, CONNECT J3 TO P1 AND P4. 2. FOR ACTIVE RETURN, CONNECT J1 TO P1 AND P2 ANDJ2 TO P3 AND P4 3.
I N S TA L L AT I O N Power Adaptor Hook-Up HON-KWANG AHEAD PLUG IN CLASS 2 TRANSFORMER AC ADAPTOR U Model: MW57-02401250A ® L LISTED 69N0 E97199 I/P: AC120V 60Hz MODEL NO: D12-10-03 O/P: 24V 1250mA INPUT:120V 60Hz 25W OUTPUT: 26VDC 1.0A POWER STRIP TERMINAL FOR 26VAC, 1A ADAPTOR 6 PICO MACOM, INC. 12500 Foothill Blvd.
I N S TA L L AT I O N Distribution T he output levels of the modulator should be the same as the output of the off-air strip amplifiers. The M860 modulators are usually combined with either the SP860 signal processor, LBS/MBS/FMS/UBS series strip amplifiers. Two methods are suggested to combine strip amplifier, modulator and processor outputs which are then amplified with the PIDA distribution amplifier serving as a launchamp.
WARRANTY Five Year Limited Warranty* P ico Macom, Inc. warrants to the original purchaser this product shall be free of defects in material and craftsmanship with only the limitations or exclusions set out below. During the warranty period Pico Macom, Inc. or an authorized Pico Macom service facility will provide, free of charge, the parts and labor necessary to correct defects in material and workmanship.
NOTES PICO MACOM, INC. 12500 Foothill Blvd.
NOTES PICO MACOM, INC. 12500 Foothill Blvd.
PICO MACOM, INC. 12500 Foothill Blvd.