Operation Manual

Action Description Display
Press the
FAN key
and
1
1
1
1
1
1
LEVEL
P2
12:0073F
SET
POWER
P3
SET
VENT-1
02
SET ROOM
TEMPERAT.
79F
CLEANING
GRATE
12:00 79F
MAX VENT
FLUE COOL
12:00 79F
select
1
1
1
1
1
1
LEVEL
P2
12:0073F
SET
POWER
P3
SET
VENT-1
02
SET ROOM
TEMPERAT.
79F
CLEANING
GRATE
12:00 79F
MAX VENT
FLUE COOL
12:00 79F
FAN SPEED
To adjust the Multifuoco setting, press the FAN key and select the desired
Multifuoco setting using the SELECT key. On the stove it is possible to
adjust the two fans separately if SEPARATE FANS has been set in the fan
mode menu. After having pressed the FAN key once (VENT 1 appears on
the display) and selected the desired Multifuoco setting for the left fan,
press the FAN key again (VENT 2 appears on the display) and select the
desired Multifuoco setting for the right fan. After the desired Multifuoco
setting has been selected the remote control returns to the INITIAL
DISPLAY. To maximise the potential of the Multifuoco function read the
paragraphs “MULTIFUOCO SYSTEM” and “MULTICOMFORT”.
1
1
1
1
1
1
LEVEL
P2
12:0073F
SET
POWER
P3
SET
VENT-1
02
SET ROOM
TEMPERAT.
79F
CLEANING
GRATE
12:00 79F
MAX VENT
FLUE COOL
12:00 79F
Press the
TEMPERATURE
key and
1
1
1
1
1
1
LEVEL
P2
12:0073F
SET
POWER
P3
SET
VENT-1
02
SET ROOM
TEMPERAT.
79F
CLEANING
GRATE
12:00 79F
MAX VENT
FLUE COOL
12:00 79F
select
1
1
1
1
1
1
LEVEL
P2
12:0073F
SET
POWER
P3
SET
VENT-1
02
SET ROOM
TEMPERAT.
79F
CLEANING
GRATE
12:00 79F
MAX VENT
FLUE COOL
12:00 79F
ROOM TEMPERATURE
To adjust the temperature setting, press the TEMPERATURE key and select
the desired temperature by using the SELECT key (range 44°F to 86°F).
When the desired temperature has been reached the readout OK appears
in the initial display and the stove operates at minimum power even if the
display shows the originally set power level. The temperature can be read
by the remote control, by the stove itself or by an external thermostat. To
choose whether the remote or the stove will read the temperature see the
paragraph “MULTICOMFORT”.
If using an external thermostat the readout “ton” appears in the initial
display and the readings from the stove and the remote control are cut out.
1
1
1
1
1
1
LEVEL
P2
12:0073F
SET
POWER
P3
SET
VENT-1
02
SET ROOM
TEMPERAT.
79F
CLEANING
GRATE
12:00 79F
MAX VENT
FLUE COOL
12:00 79F
During normal operation the automatic grate cleaning function activates
periodically, the frequency varying according to the settings pre-
programmed by Gruppo Piazzetta personnel.
This operation removes ash deposits and other buildups, which would
otherwise prevent correct stove operation.
The readout “PUL” appears in STOVE STATUS along with the ue gas
temperature.
See the PROGRAMMING section.
1
1
1
1
1
1
LEVEL
P2
12:0073F
SET
POWER
P3
SET
VENT-1
02
SET ROOM
TEMPERAT.
79F
CLEANING
GRATE
12:00 79F
MAX VENT
FLUE COOL
12:00 79F
If the temperature rises above a xed value during normal stove operation at
maximum power, the fan motor operates at maximum speed and the stove runs
at reduced heat input for a few minutes to help disperse the heat and prevent the
appliance from possibly overheating.
DT2040122-00
1
1
1
1
1
1
LEVEL
P2
12:0073F
SET
POWER
P3
SET
VENT-1
02
SET ROOM
TEMPERAT.
79F
CLEANING
GRATE
12:00 79F
MAX VENT
FLUE COOL
12:00 79F
SHUTDOWN
Action Description Display
Hold the ON/OFF key
down for several
seconds
CLEANING
BRAZIER
1 2:0022
.
c
1
Fuel loading stops, while the cooling fan and the extractor fan continue to
operate until the stove has cooled.
• The readout “PUL” appears in STOVE STATUS along with the ue gas
temperature.
• See the section on programming.
CLEANING
GRATE
1 2:0073F
1
a Never unplug the stove from the power supply at this stage as this could cause internal problems and compromise subsequent
ignition operations.
DT2040060-05
H07032120 / DT2002308 – 00
32
English