Blind Spot Information System Radar General Design Specification Document Number: 000-101863 Contents and format © 2022, Piaggio Fast Forward, Inc. BLIS General Design Specification 000-101863 -Rev A © 2022, Piaggio Fast Forward, Inc.
Revision History 2 1. Purpose and Product Usage: 1.1 Detailed Radar Description 1.1.1 Frequency Range and Modulation 1.1.2 Antennae and Array 1.1.3 Antenna Gain 1.2 Environmental 1.3 Physical Characteristics 1.3.1 Overall Characteristics 1.3.2 Mounting Dimensions 1.4 Electrical Connections 1.5 Sensor Performance 1.6 Manufacture Information 1.7 EU Restrictions 1.8 Radar Safety 3 3 4 4 4 5 5 5 6 7 7 8 8 8 2. Reference Standards 9 2.1 FCC/ISEL Decorations 10 2.1.
Revision History Revision A Date Author 12/21/2022 A. LaVita BLIS General Design Specification Description Added DoC and released 000-101863 -Rev A © 2022, Piaggio Fast Forward, Inc.
1.Purpose and Product Usage: The Blind Spot Information System (BLIS) warns the rider against collisions that may occur due to a lane change maneuver. BLIS is intended to supplement the vehicle’s rear-view mirrors, not eliminate the need for such mirrors. BLIS is intended to detect vehicles to the rear and sides of the subject vehicle and warn the rider if a lane change is not recommended.
1.1.2 Antennae and Array The radar PCBA incorporates a MIMO-array of up to 20 transmitting (Tx) and 20 receiving (Rx) antennas. The antenna array is composed of antenna elements embedded into the main printed circuit board. The antennas are not replaceable, and no provisions are made to add external antennas. The actual number of antennas used is configured by the SW (the certified profile utilized 16 transmitters).
1.3.2 Mounting Dimensions BLIS General Design Specification 000-101863 -Rev A © 2022, Piaggio Fast Forward, Inc.
1.4 Electrical Connections This unit is intended for OEM use and is not intended for any aftermarket applications. This unit must be part of the original vehicle design and part of the original vehicle harness. This can not be wired into an existing harness.
1.6 Manufacture Information The units are assembled and tested in the United States by Piaggio Fast Forward. Contacting us can be done through the following: info@piaggiofastforward.com Piaggio Fast Forward | 52 Roland Street | Boston, MA 02129 1.
2.Reference Standards The BLIS unit model R02129-BLIS is compliant with the following standards. A Certificate of Conformity is located in Appendix A of this document. Certification RED testing and certifications for EU Standards ● See Section 2.1 for operation and compliance ● ● ● ● ● ● ● ● ● ECE R10 6th Edition EN 301 489-1 V2.2.3 ETSI EN 301 489-51 V2.1.1 EN 61010-1: 2010/A1:2019 EN 62321:2009 EN 50581:2012 EN 302 264 V2.1.1 EN 62311:2008 EN 301 091-2 V1.3.2 EN 303 396 V1.1.
2.1 FCC/ISEL Decorations 2.1.1 Information for the user for operation and compliance with Chapter 15 of the FCC Rules and ISEL This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The user is not authorized to make any modifications to the equipment.
2.1.2 Information for the user for operation and compliance with Chapter 15 of the FCC Rules and ISEL CAN ICES-3 (B)/NMB-3(B) This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: This device may not cause interference; This device must accept any interference, including interference that may cause undesired operation of the device.
3. Product Marking The top side of every BLIS radar unit is marked with important identifiers that will be used to track the product. Below is a detailed description of the information that is recorded in the product label. BLIS General Design Specification 000-101863 -Rev A © 2022, Piaggio Fast Forward, Inc.
Appendix A - Declaration of Conformity Hereby, Piaggio Fast Forward declares that this R02129-BLIS is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. BLIS General Design Specification 000-101863 -Rev A © 2022, Piaggio Fast Forward, Inc.
BLIS General Design Specification 000-101863 -Rev A © 2022, Piaggio Fast Forward, Inc.
