Installation Instructions

ManualsBrandsPhoton Lighting ManualsFlush Mount LightsTyler Cordoban Bronze 2-Light Convertible Semi-Flush Mount Ceiling Light

Circulat strap

Ball nut

Lock washer

1ea Φ102*1.5tmm 2ea Φ12*10hmm 1ea Φ19*2.0t

Canopy Hex nut

Canopy loop

and Canopy

loop collar

1ea Φ153*32Hmm

1ea Φ19mm*4mm

2ea Φ9*3.5tmm

1ea Φ25*45Hmm

Chain

Threaded rod

Wire connectors

1ea 6ft* 4.2mm 1ea Φ12*55mm 6ea Orange

Chain

connector

Mounting strap Mounting screws

2ea 23.8*59mm 1ea 100mm*20mm , 1ea Φ9*10mm 4ea 8/32T*1-1/4"L

Part Needed Quantity

Reason why ( missing, scratched, broken glass, bent, bad finish)

Comments

to be filled out by retailer

IXTURE

SSEMBLY

NSTRUCTIONS

For Customer Service, contact the place of purchase to arrange for replacement parts.

NOTE: I

NSTALL THE GLASS ASSEMBLY

AFTER THE FIXTURE IS HUNG.

ASSEMBLING THE FIXTURE as Semi flush (Fig. 1)

1. Place the Circular Rim (I) over the Glass Shade (L).

2.Take the Nipple/threaded rod (G)and screw into fixture at (F).

Secure in place with hex nut (G).

3. Place the Metal Sleeve (J) and the Cap (K) onto the Nipple

(H), there should be at least 1/2" of threaded rod exposed

above the metal sleeve.

4. Place the Glass shade (L), over the nipple (H). The Nipple

(H) shall protrude through the bottom hole of the Glass shade

(L).

5. Slide the Rubber Washer (M) onto the Nipple(H).

6. Slide Bottom Cap (P) over Nipple (G) and thread the Finial

(M) until tight.

(DO NOT EXCEED THE MAXIMUM WATTAGE RATING)

8106-SF CDB

Read and review installation instruction sheet before

assembling the fixture.

Fig 1

PARTS & ASSEMBLY SHEET

This fixture assembled PO:__________ Date: ________

Fixture Name: Torbellino 8106-SF CDB

Notice:

Please review the parts listing and check for all parts before assembling the fixture. If any parts are

missing or damaged, please note onthis sheet and contact the place of purchase to arrange for

replacement parts.

PARTS LIST

Company Name:_______________________Co. Account #:_____________

Summary of content (4 pages)

PAGE 1
PARTS & ASSEMBLY SHEET Fixture Name: Torbellino 8106-SF CDB This fixture assembled PO:__________ Date: ________ Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts. PARTS LIST Company Name:_______________________Co. Account #:_____________ to be filled out by retailer Circulat strap Ball nut Lock washer 1ea Φ102*1.
PAGE 2
PARTS & ASSEMBLY SHEET Fixture Name: ASSEMBLING THE FIXTURE as Chain hung (Fig.2) Torbellino 8106-SF CDB Fig 2 1. Remove the Circular strap from top of Fixture and A2 replace the long mounting screws with two short screws to hold the Deco nuts (E) in place on the fixture Top cap B2 (D). 2. Feed the fixture wires through the Top loop (D2) and pull the wires until taut. Then screw the Top Loop（D2） E2 to the coupling on the top of fixture (D) until tight. 3.
PAGE 3
INSTALLATION INSTRUCTIONS Fixture Name: Torbellino 8106-SF CDB For Semi Flush / Convertible Light Fixture WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER. HANGING THE FIXTURE as Semi flush (Fig. 1) 1. Carefully remove the new fixture from the carton and the yellow bag that holds all your parts. Check that all parts are included as shown in the illustration and parts Fig. 1 JUNCTION BOX (CEILING) JUNCTION BOX (CEILING) list. 2.
PAGE 4
INSTALLATION INSTRUCTIONS Fixture Name: Torbellino 8106-SF CDB For Semi Flush / Convertible Light Fixture WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER. HANGING THE FIXTURE as Chain hung (Fig.1) Fig. 1 1. Carefully remove the new fixture from the carton and the yellow bag that holds all parts. Check that all parts are included JUNCTION BOX (CEILING) as shown in the illustration and parts list. 2.