Digitrack TABLE OF CONTENTS page SAFETY INSTRUCTIONS ............................................................................ 4 INTRODUCTION ........................................................................................... 4 BOX CONTENTS .......................................................................................... 5 FEATURES.................................................................................................... 5 SYSTEM REQUIREMENTS ...................................
SAFETY INSTRUCTIONS 1. Read all instructions carefully before using Digitrack. 2. Keep this user's manual for future reference. 3. Please follow all instructions. 4. You should use properly functioning cables in good repair to connect all devices to Digitrack. 5. Do not try to service this product yourself. If servicing is required, contact your local service center.
BOX CONTENTS Digitrack USB Audio Interface One standard USB cable User's Manual FEATURES USB computer interface (compatible with most PC and Mac computers) 16-bit digital audio Supports 44.1 and 48 KHz sampling rates Two unbalanced line-level RCA inputs Two unbalanced line-level RCA outputs One S/PDIF digital input One S/PDIF digital output 1/8" (3.
SYSTEM REQUIREMENTS Windows Microsoft® Windows® 98/Me/2000 Professional/XP Available USB port [ME/98] Intel Pentium®, Celeron® or Intel compatible processor (233 MHz or higher) [XP/2000] Intel Pentium®, Celeron® or Intel compatible processor (400 MHz or higher) [ME/98] 64 MB or more of RAM [XP/2000] 128 MB or more of RAM 120 MB or more of free hard drive space Macintosh OS 9.0.4 or later with native USB support OS X 10.
4 1 10 9 8 7 2 3 5 6 PANEL DESCRIPTION 1) USB Power Indicator The LED will illuminate to indicate that Digitrack is receiving power from the USB bus and ready to send and receive signals. The computer must be turned on and Digitrack must be connected to a properly functioning USB port on the computer. 2) Stereo RCA Input Signal Indicator The LED signal indicator will flash when a source signal is present.
8 9 10 7) Stereo RCA Outputs 4output of your1computer2is converted 3to analog and is sent to these stereo The digital RCA output jacks. Using these jacks, connect Digitrack to the record input on a mixer, tape deck or CD player, or connect them to the AUX inputs on your home stereo system for great sounding playback. 8) Stereo RCA Inputs Stereo RCA input jacks. Connect the 2T (Tape) analog output from a mixer, CD player 5 6 or tape deck here for input to the computer.
INSTALLATION USB Port on computer Series A Series B 1) Connect the Series A end of the USB cable to the USB port on the computer. 2) Connect the Series B end of the USB cable to the USB port on Digitrack. 3) The LED illuminates to indicate that Digitrack is receiving power from the computer. SETUP There is no need to install external drivers for Digitrack. It works with the core audio driver in Microsoft® Windows® and Apple® Macintosh® computers.
ASIO Drivers In some cases, the Windows driver may have problems with latency. If you experience latency issues you may want to try the following ASIO drivers. http://www.asio4all.com/ http://www.usb-audio.com/ Note: These entities are not affiliated with Phonic, however they offer ASIO drivers that will work with Digitrack. Phonic does not offer technical support for ASIO drivers and will not be held responsible for any damage sustained to property from installing or using these drivers.
APPLICATIONS 1) Recording audio on the computer from an analog source (mixer, tape deck) First, use the provided USB cable to connect Digitrack to a computer with an available USB port. Then, locate the stereo RCA outputs of your mixer or tape deck. Use a stereo RCA cable to connect the outputs of the device to the stereo RCA inputs on Digitrack. Open the audio recording software on the computer. Increase the source output until it reaches the desired level.
SPECIFICATIONS Sampling Rates DAC: 32, 44.1 and 48 KHz ADC: 8, 11.025, 16, 22.05, 32, 44.
PURCHASING PHONIC GEAR AND OPTIONAL ACCESSORIES To purchase Phonic gear and optional accessories, please contact an authorized Phonic distributor. For a list of nearby Phonic distributors please visit our website at www.phonic.com and click on Get Gear. You may also contact Phonic directly and we will assist you in locating a distributor: Phonic 6103 Johns Road, #7 Tampa, FL 33634 (813) 890-8872 SERVICE AND REPAIR Phonic has over 100 service centers worldwide.
