Roger Select™ iN User Guide
Contents 1. 2. 2.1 2.2 2.3 3. 3.1 3.2 3.3 4. 4.1 4.2 5. 5.1 5.2 6. 7. 7.1 7.2 7.
1. Welcome 2. Getting to know your Roger Select iN Your Roger Select iN iN has been developed by Phonak – the world leader in hearing solutions based in Zurich, Switzerland. Roger Select iN is a microphone that picks up the voice of a speaker and sends it wirelessly directly into your ears. You can place Roger Select iN in the middle of a table e.g. in a restaurant, or it can be worn by a single person i.e. to hear a distant talker.
2.1 Device description 1 5 2 ➃ ➃ ➃ ➂ ➃ 10 6 7 10 8 ➃ ➃ 9 1 2 3 4 5 6 On/off button incl.
2.
2.
3. Getting started 3.1 Charging your Roger microphone There are three ways to charge your Roger microphone: A) Using external power supply: Plug the smaller end of the charging cable into your Roger microphone. Plug the larger end of the cable into the external power supply. Plug the external power supply into a wall outlet. B) From computer or tablet: Plug the smaller end of the charging cable into your Roger microphone.
3.3 Connecting Roger Select iN to your Roger receiver The Roger receiver can either be installed into your hearing aid, attached to your hearing aid / sound processor or body-worn (Roger MyLink or Roger X plugged into your streamer). 3.2 Switching Roger Select iN on Press the button 1 second until the microphone mode indicator light up. 1s Battery status light after switching on When your Roger microphone is switched on, the battery status light around the on/off button will blink softly.
Connect status lights After pressing the Connect button, the following feedback may be given by the back indicator light: Connecting Connection was successful – your Roger receiver is connected to your Roger microphone. Your Roger microphone could not find a Roger receiver. Move the devices closer to your Roger receiver and make sure the Roger receiver is powered on. Then try to connect again. The Roger receiver is not compatible with your Roger microphone. 4.
Your Roger microphone will activate an all-around microphone. When a talker speaks, your Roger microphone will focus its microphone to the talker and reduce the background noise. If two or more people are speaking at the same time, you may tap a segment to focus on a specific person. You can add other people by tapping additional segments. Microphone mode indicator lights Each time you tap or move the device, the microphone mode indicator lights shows the active segments.
4.2 Hearing a distant talker better Roger Select iN allows you to hear a single conversation partner over distance or in very noisy environments. In typical conditions, you may hear the talker even if they are 10 meter/30 feet away from you. Using the clip 1) Attach the clip to your Roger microphone. Make sure the clip clicks into the small slots on the side of your Roger microphone. 2) Open the magnetic clip. 3) Attach the clip to the talker’s shirt.
Using the lanyard 1) Attach the lanyard to your Roger microphone. Make sure the lanyard clicks into the small slots on the side of your Roger microphone. 2) Hang the lanyard around the neck of the talker and adjust the length so that your Roger microphone is within 20 cm/8 inches of the mouth. 5. Listening to TV or other audio devices 5.1 Setting up the docking station 1) Insert the smaller end of the USB cable into the socket of the docking station.
5.2 Listening to the TV using the docking station 4) Connect the free end of the optical (Toslink) cable into the optical OUTPUT of your TV or alternative audio device. AL OPTIC L DIGITA T OU AUDIO TV OPTICAL TV DIGITAL OUT AUDIO If your TV or alternative audio device does not have optical audio output, you can alternatively use an analogue audio cable for connection between the TV and the docking station. The maximum audio output is 1.4 Vrms, higher audio input voltage may damage the device.
Mute indicator lights When your Roger microphone is placed in the docking station and transmitting audio, the center red indicator light appears. Your Roger microphone transmits audio signals while its microphone is muted. 6. Listening to a portable audio device 1) Make sure you have switched on your Roger microphone. 2) Plug the rectangular end of the short audio cable into your Roger microphone. 3) Plug the round end of the short audio cable into the headphone output of your portable device.
7. Additional functions Mute indicator lights When the audio cable is plugged into your Roger microphone, the center red indicator light appears. Your Roger microphone transmits audio signals while its microphone is muted. 7.1 Mute To mute the your Roger microphone, tap the center touch key of the device once or twice until the center red indicator light appears. Tap the center touch key to re-activate the Roger microphone. When the device is worn by a talker, the mute function cannot be used.
8. Using Roger Select iN with other Roger microphones 7.3 Reset If your Roger microphone stops responding to commands, you can reset it by pressing the on/off and reset buttons together for 10 seconds (you may need a thin paper-clip to press the reset button). Roger Select iN can be combined with other Roger microphones, e.g. Roger Table Mic II. Using multiple microphones allows you to hear a bigger group or multiple distant speakers. 8.1.
Connect status light After pressing the Connect button, the following feedback may be given by the back indicator light: 8.2. Using multiple microphones When Roger Select iN is used with other microphones, it has to be worn by a talker on the chest. When you place Roger Select iN on the table, it will mute automatically. Unmuting Roger Select iN will mute the other microphones that are connected with the Roger Select iN.
9.
Problem Causes Solutions I do not like to hear my own voice over my Roger microphone Your voice is picked up by your Roger microphone Tap the segment in the direction of the talker to minimize your own voice pickup The volume of my multimedia device is too low Incorrect volume settings Increase volume of your audio source I cannot hear my multimedia device The audio source is muted Unmute the audio source your Roger microphone is switched off Switch on your Roger microphone The audio cable is
11. Compliance information 10.3 Warranty limitation This warranty does not cover damage from improper handling or care, exposure to chemicals, immersion in water or undue stress. Damage caused by third parties or non-authorized service centers renders the warranty null and void. This warranty does not cover any services performed by a hearing care professional in his/her office.
Notice 1: This device complies with Part 15 of the FCC Rules and with Industry Canada’s license exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device. the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
12. Information and explanation of symbols Notice 4: Japanese Radio Law Compliance. Business Law Compliance. This device is granted pursuant to the Japanese Radio Law . This device should not be modified (otherwise the granted designation number will become invalid). Notice 5: FCC / Industry Canada RF Radiation Exposure Statement This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
Operating conditions The device is designed such that it functions without problems or restrictions if used as intended, unless otherwise noted in this user guide. Temperature transport and storage: –20° to +60° Celsius (–4° to +140° Fahrenheit). Temperature operation: 0° to +40° Celsius (+32° to +104° Fahrenheit). Keep dry. Humidity during transportation and storage: <90% (non-condensing). Humidity operation: <90% (non-condensing).
13. Important safety information Please read the information on the following pages before using your device. 13.1 Hazard warnings 46 Use only hearing aids that have been specially programmed for you by your hearing care professional. Dispose of electrical components in accordance with your local regulations. This device is not for children below 36 months. It contains small parts that can cause choking, if swallowed by children. Keep out of reach of children and mentally challenged people or pets.
Do not use the device in explosive areas (mines or industrial areas with danger of explosions, oxygen rich environments or areas where flammable anesthetics are handled) or where electronic equipment is prohibited. Opening the device might damage it. If problems occur which cannot be resolved by following the remedy guidelines in the troubleshooting section of this user guide, consult your hearing care professional. When operating machinery, ensure that no parts of your device can get caught in the machine.
Notes If the device has been dropped or damaged, if it overheats, has a damaged cord or plug, or has been dropped into liquid, stop using your device and contact authorized service centre. 13.3 Other important information Protect your eyes of the optical light from the optical Toslink cable when plugged into the device or TV. High-powered electronic equipment, larger electronic installations and metallic structures may impair and significantly reduce the operating range.
029-0755-02/V1.00/2019-01/na © 2017 Sonova AG All rights reserved Phonak Communications AG Länggasse 17 CH-3280 Murten Switzerland www.phonak.
