029-4004-02/V1.00/2016-01/SH © Phonak AG All rights reserved Phonak Communications AG Laenggasse 17 CH-3280 Murten Switzerland www.phonak.
Contents 1. Welcome 4 2. Getting to know your Roger Table Mic 6 3. 4. Special functions 27 6 6.1 Muting 27 2.2 How Roger Table Mic works 7 6.2 Disconnecting Roger devices (NewNet) 28 2.3 Device descriptions 8 2.4 Indicator lights 9 Getting started 10 3.1 Setting up the power supply 10 3.2 Charging Roger Table Mic 12 3.3 Setting up the remote control 14 3.4 Switching on and off 15 3.5 Using Roger receivers 16 3.6 Connecting a receiver 17 3.
1. Welcome Congratulations on choosing the Roger Table Mic from Phonak. Roger Table Mic is a wireless microphone for full participation in small and big meetings. You simply place it on the table. The spoken words of the meeting participants are distinguissed and the backgroud noise is reduced. With its discreet design it blends in perfectly well with the rest of your meeting equipment. Please read this User Guide thoroughly to benefit from all the possibilities Roger Table Mic offers.
2. Getting to know your Roger Table Mic 2.1 In the box 2.2 How Roger Table Mic works Roger Table Mic transmits the meeting participants‘ voices directly into your ears. The system consists of three main elements: the hearing aids, Roger receivers and one or more Roger Table Mic(s).
2.3 Device descriptions 2.4 Indicator lights Roger Table Mic Indicator light a b f e a b c c d d e f Indicator light Microphones On / Off / Mute Connect Charging input Audio input a b c d e Indicator light Mute on Mute off Screw Battery cover Meaning Switched on Switched off Audio input detected Microphone / audio input muted Charging Fully charged Low battery – charge Roger Table Mic Roger Table Mic has lost connection to the other Roger microphone(s).
3. Getting started 3.1 Setting up the power supply The universal power supply comes with an adapter for your country. To charge your device you first need to attach the correct adapter to the power supply. Remove / Change: 1. Pull back the tab on the universal power supply. 2. Gently pull the adapter upwards to remove it. 1. 2. 1. Select the power adapter that corresponds to your country. US EU UK 2. Insert the top (round) end of the adapter in the top end of the universal power supply. 3.
3.2 Charging Roger Table Mic Roger Table Mic contains a built-in lithium polymer battery with fast-charge capability. To charge Roger Table Mic, connect the supplied charger. The indicator light will turn orange to indicate it is charging. 1. Plug the smaller end (micro-USB) of the charging cable into Roger Table Mic. 2. Plug the larger end (USB) of the charging cable into the power supply. 3. Plug the power supply into an easily accessible power socket.
You can also charge Roger Table Mic by connecting it to a computer’s USB port using the supplied charging cable. Indicator lights (battery status) Indicator light Meaning Charging Fully Charged Low battery – charge Roger Table Mic. In addition, you will hear beeps in your hearing aids. 3.4 Switching on and off To switch Roger Table Mic on, press the on/off button for one second until the indicator light turns green. 3.
16 3.5 Using Roger receivers 3.6 Connecting a receiver Using Roger MyLink If your Roger receiver is a Roger MyLink, switch the Roger MyLink on and hang it around your neck. Make sure your hearing aids are set to T / MT / T-Coil mode. Your hearing care professional may already have connected Roger Table Mic to your hearing aids. If this is not the case, connect your receiver to Roger Table Mic as follows: The Roger MyLink User Guide provides more detailed information on using Roger MyLink. 2.
The indicator light will turn green for two seconds to confirm a successful connection. 4. Repeat steps 2 and 3 to connect a second receiver. You can connect an infinite number of Roger receivers to Roger Table Mic. Indicator light (connection status) button, the following After pressing the Connect feedback may be given by the indicator light: Indicator light 18 Meaning Connecting Connection was successful – the Roger receiver is connected to Roger Table Mic.
4. Using Roger Table Mic Roger Table Mic is a flexible, intelligent product. It detects which situation you are in and adapts its sound processing settings automatically to provide you the best speech understanding possible. Place Roger Table Mic in the middle of a table to listen to a group of people. 4.1 Connecting to multimedia devices You can connect Roger Table Mic to an audio source – such as a conference telephone, tablet or computer - to hear its audio signal directly in your hearing aids. 1.
5. Adding additional microphones Roger technology allows you to use multiple microphones in parallel by connecting additional Roger microphones. 5.1 Connect The indicator lights of both microphones will turn green for two seconds to indicate successful connection. It’s possible to add up to 10 other Roger microphones to Roger Table Mic. To connect another microphone to your Roger Table Mic, follow these steps: 1. Turn on both microphones.
Indicator light (Connection status) button, the following After pressing the Connect feedback may be given by the indicator light: Indicator light Meaning Connection was successful - the other Roger microphone is now connected to Roger Table Mic. Roger Table Mic could not find another Roger microphone. Move Roger Table Mic closer to the other Roger microphone and make sure both microphones are switched on. Then try Connect again. The other Roger microphone is not compatible with Roger Table Mic.
6. Special functions If there is an issue with the network, press the button on one of the microphones to Connect reinitialize the network. Indicator light (multiple microphone status) When using multiple Roger microphones, the following feedback may be given by the indicator light: Indicator light Meaning The Roger microphone is muted. Unmute it by pressing the on/off button or the mute off button on the remote control. Roger Table Mic has lost connection to the other Roger microphone(s).
7. Troubleshooting 6.2 Disconnecting Roger devices (NewNet) To disconnect Roger Table Mic from any connected receivers or other Roger microphones, hold the button for 7 Connect seconds. The indicator light will turn orange when Roger Table Mic has been disconnected from all connected devices.
7.
8. Important information 8.1 Important safety information Please read the information on the following pages before using your Phonak device. This symbol on the product or its packaging means that it should not be disposed of with your other household waste. It is your responsibility to dispose of your waste equipment separately from the municipal waste stream. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 8.
External devices should only be connected if they have been tested in accordance with corresponding IECXXXXX standards. Only use accessories that are approved by Phonak AG. Using your device’s cables in any way contradictory to their intended purpose (e. g., wearing the USB cable around the neck) can cause injury. When operating machinery, ensure that no parts of your device can get caught in the machine. Do not charge device while it is on your body. Caution: electric shock.
Protect the device from excessive moisture (bathing, swimming), heat (radiator, car dashboard), and direct contact with skin when sweating (workout, fitness, sport). X-ray radiation, CT or MRI scans may destroy or adversely affect the correct functioning of the device. Do not use excessive force when connecting your device to its different cables. Insert the device into the docking station as indicated. Incorrect insertion may damage the device.
9. Service and warranty 9.1 Local warranty 9.3 Warranty limitation Please ask the hearing care professional, where you purchased your device, about the terms of the local warranty. This warranty does not cover damage from improper handling or care, exposure to chemicals, immersion in water or undue stress. Damage caused by third parties or non-authorized service centers renders the warranty null and void.
10. Information and explanation of symbols The CE symbol is confirmation by Phonak Communications AG that this Phonak product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. This device is designed such that it functions without problems or restrictions if used as intended, unless otherwise noted in these user guides. Australian EMC and Radiocommunications compliance label.
The symbol with the crossed-out garbage bin is to make you aware that this device may not be thrown away as normal household waste. Please dispose of old or unused device, at waste disposal sites intended for electronic waste, or give your device to your hearing care professional for disposal. Proper disposal protects the environment and health. This product has an embedded, nonreplaceable battery. Do not attempt to open the product or remove the battery as this may cause injury and damage the product.
