Technical data

ManualsBrandsPhoenix ManualsPower Supply UnitsTRIO-PS/1AC/24DC/2.5

Primary switched power supply, 1-phase,

output current: 5 A

TRIO-PS/1AC/24DC/5

Data Sheet

INTERFACE

TRIO POWER is the rail mountable 24 V power supply unit

with basic functions. With an output voltage of 24 V DC and

1-phase and 3-phase versions with 60 W or 960 W, it is par-

ticularly suited for use in series production in mechanical en-

gineering. The wide-range input and international certifica-

tion package allows worldwide implementation.

The high MTBF of 500,000 h stands for high supply reliability.

The devices can be connected in parallel to increase the ca-

pacity and redundancy.

The clear LED signaling and the device connection with dou-

ble terminal block for plus and minus for fast potential distri-

bution are further advantages of this device series. A third

terminal block for minus simplifies the grounding on the sec-

ondary side. All power supply units are idle proof and short

circuit proof and provide a regulated and settable output volt-

age of 22.5 V DC to 29.5 V DC with output currents of 2.5 A,

5 A, 10 A, 20 A or 40 A.

Description

DANGER OF EXPLOSION!

Remove an item only when it is not connected to power or if it is located in the non-explosive area.

DANGER

Components with dangerously high voltage and high stored energy are located in the device!

Never carry out work on live parts!

Depending on the ambient temperature and the load, the housing can become very hot!

Make sure you always use the the latest documentation.

It can be downloaded at www.download.phoenixcontact.com

A conversion table is available on the Internet at

www.download.phoenixcontact.com/general/7000_en_00.pdf.

– Reliable power supply unit even at high ambient temper-

atures

– No load and short circuiting resistance

– High dielectric strength

– Can be used worldwide in all industrial sectors due to a

wide-range input and an international approval package

102777_02_en

Summary of content (13 pages)

PAGE 1
TRIO-PS/1AC/24DC/5 Primary switched power supply, 1-phase, output current: 5 A INTERFACE Data Sheet 102777_02_en © PHOENIX CONTACT - 06/2007 Description TRIO POWER is the rail mountable 24 V power supply unit with basic functions. With an output voltage of 24 V DC and 1-phase and 3-phase versions with 60 W or 960 W, it is particularly suited for use in series production in mechanical engineering. The wide-range input and international certification package allows worldwide implementation.
PAGE 2
TRIO-PS/1AC/24DC/5 Table of contents Description ........................................................................................................................................................................1 Table of contents ............................................................................................................................................................2 Order data .........................................................................................................
PAGE 3
TRIO-PS/1AC/24DC/5 Order data Description Type Order No. Pcs./Pkt. Primary switched power supply, 1-phase, output current: 5 A TRIO-PS/1AC/24DC/5 2866310 1 Technical data Input data Input nominal voltage range 100 V AC ... 240 V AC AC input voltage range 85 V AC ... 264 V AC (derating < 90 V AC: 2.5% per Kelvin) AC frequency range 45 Hz ... 65 Hz Current consumption 1.65 A (120 V AC) 0.9 A (230 V AC) Inrush current limitation < 15 A I2t 1.
PAGE 4
TRIO-PS/1AC/24DC/5 General data Insulation voltage input/output 4 kV AC (Type test) 2 kV AC (routine test) Insulation voltage input / PE 2 kV AC (type test) 2 kV AC (routine test) Insulation voltage output / PE 500 V DC (type test) Degree of protection IP20 Class of protection I, with PE connection MTBF > 500 000 h in acc.
PAGE 5
TRIO-PS/1AC/24DC/5 Conformance with EMC directive 89/336/EEC Immunity to interference in acc. with EN 61000-6-2 Discharge of static electricity Housing Level 3 Contact discharge 6 kV Discharge in air 8 kV Comments Criterion B Housing Level 3 Frequency range 80 MHz ...
PAGE 6
TRIO-PS/1AC/24DC/5 Structure 2 4 + + – – – Ou t 24put D V C 5A DC OK 3 1 2 3 4 5 6 AC input DC output Potentiometer 22.5 V DC ... 29.5 V DC "DC OK" LED DIN rail adapter Take-up for cable binders TRIO POWER 5 A 22 dju .5- st 29 .5V 1 L Input Output N [mm2] solid stranded 0.2 - 2.5 0.2 - 2.5 0.2 - 2.5 0.2 - 2.5 AWG 24 - 14 24 - 14 [Nm] Torque 0.4 - 0.5 0.4 - 0.5 In 10put A 0-2 C 40 V 6 Input data Input nominal voltage range 100 V AC ... 240 V AC AC input voltage range 85 V AC ...
PAGE 7
TRIO-PS/1AC/24DC/5 Block diagram L N PE Safety and warning notes The power supply units are built-in devices. The device may only be installed and put into operation by qualified personnel. The corresponding national regulations must be observed. DANGER OF EXPLOSION! Remove an item only when it is not connected to power or if it is located in the non-explosive area.
PAGE 8
TRIO-PS/1AC/24DC/5 Installation In order to guarantee sufficient convection, we recommend observing the following minimum distance to other modules: 5 cm in a vertical direction and 0 cm in a horizontal direction. + + – – – Ou tp 24 ut D V C 5A DC OK TRIO POWER The power supply unit can be snapped onto all DIN rails in acc. with EN 60715. They must be mounted horizontally (connecting terminal blocks top and bottom). A 22 dju .5-2 st 9.
PAGE 9
TRIO-PS/1AC/24DC/5 A Assembly B Position the module with the DIN rail guide on the upper edge of the DIN rail, and snap it in with a downward motion. Removing Pull the snap lever open with the aid of a screwdriver and slide the module out at the lower edge of the DIN rail. B A Connection to various network forms TN-S TN-C TT L N PE L L PEN L N PE + - iT N PE L + - The connection for 100 V AC ... 240 V AC is made using the L, N and PE screw connections.
PAGE 10
TRIO-PS/1AC/24DC/5 Input Protection of the primary side + + – – – Ou tp 24 ut D V C 5A DC OK A 22 dju .5-2 st 9.5 V L N TRIO POWER The device must be installed in acc. with the regulations as in EN 60950. It must be possible to disconnect the device using a suitable isolating facility outside the power supply. The primary side line protection, for example, is suitable. For device protection, there is an internal fuse. Additional device protection is not necessary.
PAGE 11
TRIO-PS/1AC/24DC/5 Output + + – – – Ou tp 24 ut D V C 5A DC OK You can fasten the connection cables to the housing using cable binders. Ensure that the cable binders and the connection cables are designed for the surface temperatures that occur in operation. Make sure that the insulation of the connection cables is not damaged when tightening the cable binders. TRIO POWER Ou 24 tput V DC 2.
PAGE 12
TRIO-PS/1AC/24DC/5 Function UOUT [V] Output characteristic curve UN IN IOUT [A] The device functions following the U/I characteristic curve. Under load, the working point follows this curve. The output current is limited in the event of a short circuit or overload. Thereby, the device does not switch off, but rather supplies a continuous output current. The secondary voltage is reduced until the short circuit or overload on the secondary side has been remedied.
PAGE 13
TRIO-PS/1AC/24DC/5 Parallel operation Devices of the same type can be connected in parallel to enable both redundancy and an increase in efficiency. No other alignment is necessary when in the state of delivery. If the output voltage is adjusted, a uniform distribution of power is guaranteed by setting all parallel operated power supply units to exactly the same output voltage.