Datasheet

ManualsBrandsPHOENIX CONTACT ManualsRack & DIN Rail Mount PSUsRail mounted PSU (DIN) MINI-SYS-PS-100-240AC/24DC/1.5 24 Vdc 1.5 A 36 W 1 x

MINI POWER provides:

•

Extra narrow

design with widths of 22.5 mm,

45 mm, and 67.5 mm (0.886, 1.772, and 2.657 in.)

•

Global use

due to a wide-range voltage input

•

A high level of operational safety

in complex

global networks

•

Reliable startup

of heavy loads due to

POWER BOOST

The reliability of a power supply unit determines the

availability of individual components in a system and

whether complex systems can function safely.

The globalization of markets increases the demands

placed on the power supply unit. A wide-range voltage

input and a high level of availability are required. These

requirements are met by MINI POWER.

1. Short Description

MINI POWER is the extra narrow power supply unit,

which is available in widths of 22.5 mm, 45 mm, and

67.5 mm (0.886, 1.772, and 2.657 in.).

In addition to a 24 V version with output currents of

1 A, 2 A, and 4 A, special voltages are also available

with 5 V/3 A, +/-15 V/1 A, and 10 - 15 V/2 A for

connection to single-phase AC networks or to two

external conductors in three-phase networks with

nominal voltages of 100 - 240 V AC. Two DC/DC

converters convert low direct voltages into an

adjustable and regulated 24 V output voltage.

With the DIN rail bus connector, the MINI-SYS-PS

can be connected in parallel to supply other modules in

the same system with a regulated 24 V DC voltage.

Reliable startup of heavy loads is ensured by a

power reserve of up to 100% – the POWER BOOST.

The high level of operational safety is also ensured in

complex global networks. MINI POWER also operates

in applications where static voltage dips, transient

power supply failures or phase failure are common.

Powerful capacitors ensure mains buffering of more

than 20 ms at full load.

2. Area of Application

MINI POWER can be used globally due to the

consistent provision of a wide-range voltage input.

In this way, your entire system can be tested at any

production location in the world and can be delivered to

any location in the world without faulty switching of the

input voltage. This reduces storage costs and logistical

effort.

An international approval package including

UL 60950 for IT equipment and UL 508 for industrial

control equipment enables the device to be used

globally.

Power Supply Unit, Primary Switched, Narrow Design

MINI-SYS-PS-100-240AC/24DC/1.5

Phone +49 - 52 35 - 30 0 • Fax +49 - 52 35 - 34 12 00 • www.phoenixcontact.com

Local Contact: www.phoenixcontact.com/salesnetwork

Summary of content (8 pages)

PAGE 1
Power Supply Unit, Primary Switched, Narrow Design MINI-SYS-PS-100-240AC/24DC/1.5 MINI POWER provides: • Extra narrow design with widths of 22.5 mm, 45 mm, and 67.5 mm (0.886, 1.772, and 2.657 in.
PAGE 2
Power Supply Unit, Primary Switched, Narrow Design – MINI-SYS-PS-100-240AC/24DC/1.5 3. Technical Data 102.5 mm (4.035 in.) 0V NC 0V N 24V 13 99 mm (3.898 in.) 24V L 14 35 mm (1.378 in.) MINI-SYS-PS-100-240AC/24DC/1.5 Uu 1 AC 7 mm (0.28 in.) Input Output Signal Solid Stranded [mm2] AWG 0.2 - 2.5 0.2 - 2.5 0.2 - 2.5 Torque [Nm] [Ib in] 0.2 - 2.5 25 - 14 0.5 - 0.6 4.4 - 5.3 0.2 - 2.5 25 - 14 0.5 - 0.6 4.4 - 5.3 0.2 - 2.5 25 - 14 0.5 - 0.6 4.4 - 5.3 Description Type Order No.
PAGE 3
Power Supply Unit, Primary Switched, Narrow Design – MINI-SYS-PS-100-240AC/24DC/1.
PAGE 4
Power Supply Unit, Primary Switched, Narrow Design – MINI-SYS-PS-100-240AC/24DC/1.5 4. Device View, Connections, and Control Elements 2 5A 14 1. V 13 24 0V V DC 24 UT 0V O V 24 4 3 C D K O R WE PO YS -S NI MI IN 1 0 24 010 N C A NC L V A2 12 2 71 –25 - 25 … + 60 °C - 13 … + 140 °F INFORMATION TECHNOLOGY EQUIPMENT u Read installation instructions before connecting to mains INDUSTRIAL CONTROL EQUIPMENT 1YD8 www.interface.phoenixcontact.com APPROVALS LISTED U 72 Order No.
PAGE 5
Power Supply Unit, Primary Switched, Narrow Design – MINI-SYS-PS-100-240AC/24DC/1.5 6. Installation 6.1. Mounting The power supply unit can be snapped onto all DIN rails according to EN 60715. The device must be mounted horizontally (input terminal blocks facing downwards). Installation Dimensions V 24 13 14 71 72 V 24 0V To ensure sufficient convection, a minimum spacing of 5 cm (1.969 in.) to other modules is required above and below the device.
PAGE 6
Power Supply Unit, Primary Switched, Narrow Design – MINI-SYS-PS-100-240AC/24DC/1.5 6.2. Connection of Various Types of Network: 100 - 240 V AC networks TN-S network TN-C network TT network L PEN L N PE L N L N + – MINI L N L N + – MINI + – MINI L1 L2 L3 N PE L1 L2 L3 PEN L N MINI IT network L N +– MINI L1 L2 L3 PE L1 L2 L3 N L N L N +– +– MINI MINI +– Figure 08 4 1 C D K O AWG Torque [Nm] [Ib in] 25 - 14 0.5 - 0.6 4.4 - 5.3 25 - 14 0.5 - 0.6 4.4 - 5.3 25 - 14 0.5 - 0.
PAGE 7
Power Supply Unit, Primary Switched, Narrow Design – MINI-SYS-PS-100-240AC/24DC/1.5 6.4. Output (2, Figure 9) The 24 V DC connection is made using the "+" and "-" screw connections on the screw connection 2 and the DIN rail bus connector. Electrically isolated contact Output 24V DC Protecting the Secondary Side: The device is electronically short-circuit-proof and idling-proof. In the event of an error, the output voltage is limited to a maximum of 30 V DC.
PAGE 8
Power Supply Unit, Primary Switched, Narrow Design – MINI-SYS-PS-100-240AC/24DC/1.5 UOUT = 24 V Output current [A] 2A 1.5 7.3. Parallel Operation Devices of the same type can be connected in parallel to increase both redundancy and power. The default setting does not have to be adjusted. If the output voltage is adjusted, an even current distribution can be ensured by precisely setting all power supply units that are operated in parallel to the same output voltage.