Datasheet

ManualsBrandsPHOENIX CONTACT ManualsRack & DIN Rail Mount PSUsRail mounted PSU (DIN) QUINT-PS/3AC/24DC/20 24 Vdc 20 A 480 W 1 x

Description

Primary-switched power supply with SFB

technology, 3 AC, output current 20 A

QUINT-PS/3AC/24DC/20

Data Sheet

INTERFACE

QUINT POWER power supply units – highest system

availability due to SFB technology

Compact power supply units of the new QUINT POWER

generation maximize the availability of your system. Even

the standard power circuit-breakers can be tripped reliably

and quickly with the SFB technology (Selective

Fusebreaking Technology) and six times the nominal current

for 12 ms. Defective current paths are disconnected

selectively, the defect is limited and the important system

parts remain in operation. A comprehensive diagnostics is

carried out by continuously monitoring the output voltage and

current. This preventive function monitoring visualizes the

critical operating modes and reports them to the control unit

before an error occurs.

DANGER OF EXPLOSION!

Remove an item only when it is not connected to power or if it is located in the non-explosive area!

DANGER

Components with dangerously high voltage and high stored energy are located in the device!

Never carry out work on live parts!

Depending on the ambient temperature and the load, the housing can become very hot!

Make sure you always use the the latest documentation.

It can be downloaded at www.download.phoenixcontact.com

A conversion table is available on the Internet at

www.download.phoenixcontact.com/general/7000_en_00.pdf.

Features

– Quick tripping of standard power circuit breakers with

dynamic SFB technology power reserve

– Reliable starting of difficult loads with static POWER

BOOST power reserve

– Preventive function monitoring

– Can be used worldwide

– High operating safety due to long mains buffering under

full load and high MTBF (> 500,000 h)

– Perfect functioning even in the event of a permanent

phase failure

– High surge voltage strength up to 6 kV (surge,

asymmetric) using an integrated gas arrester

103132_en_00

Summary of content (14 pages)

PAGE 1
QUINT-PS/3AC/24DC/20 Primary-switched power supply with SFB technology, 3 AC, output current 20 A INTERFACE Data Sheet 103132_en_00 © PHOENIX CONTACT - 11/2007 Description Features QUINT POWER power supply units – highest system availability due to SFB technology Compact power supply units of the new QUINT POWER generation maximize the availability of your system.
PAGE 2
QUINT-PS/3AC/24DC/20 Table of contents Description ........................................................................................................................................................................1 Table of contents ............................................................................................................................................................2 Ordering data ....................................................................................................
PAGE 3
QUINT-PS/3AC/24DC/20 Ordering data Description Type Order No. Pcs./Pkt. Primary-switched power supply with SFB technology, 3 AC, output current 20 A QUINT-PS/3AC/24DC/20 2866792 1 Accessories Type Order No. Pcs./Pkt. Assembly adapter for QUINT POWER 2.5 A and 5 A on S7-300 rail QUINT-PS-ADAPTERS7/1 2938196 1 Universal wall adapter UWA 182/52 2938235 1 Technical data Input data Input nominal voltage range 2/3x 400 V AC ... 500 V AC AC input voltage range 3x 320 V AC ...
PAGE 4
QUINT-PS/3AC/24DC/20 Signal output DC OK active Output description UOUT > 0.9 x UN: High signal Voltage + 24 V DC Current ≤ 20 mA (short circuit resistant) Status display "DC OK" LED green / UOUT < 0.9 x UN: LED flashing Signal output DC OK floating Output description Relay contact, UOUT > 0.9 x UN: Contact closed Voltage ≤ 30 V AC/DC Current ≤ 1 A (≤ 0.5 A / at 60 V AC/DC) Status display "DC OK" LED green / UOUT < 0.
PAGE 5
QUINT-PS/3AC/24DC/20 Standards Protection against electric shock, basic requirements for safe isolation in electrical equipment DIN VDE 0106-101 Limitation of mains harmonic currents EN 61000-3-2 Device safety GS (tested safety) Network variants (undervoltage) Semi F47-200 Certificate CB Scheme Approvals UL rating UL Listed UL 508 UL/C-UL Recognized UL 60950 (3-wire + PE, star net) Conformance with EMC directive 2004/108/EC Noise immunity according to EN 61000-6-2 Electrostatic discharge Electr
PAGE 6
QUINT-PS/3AC/24DC/20 Structure 9 5 4 1 2 3 4 5 6 7 8 9 AC input DC output POWER BOOST switching output, active DC OK switching output active DC OK output, floating Potentiometer 18 V DC ... 29.5 V DC "DC OK" LED "BOOST" LED Universal DIN rail adapter UTA 107/30 3 1 2 6 7 8 Input Output Signal [mm2] solid stranded 0.2 - 6 0.2 - 4 0.2 - 6 0.2 - 4 0.2 - 6 0.2 - 4 AWG 18 - 10 12 - 10 18 - 10 [Nm] Torque 0.5 - 0.6 0.5 - 0.6 0.5 - 0.6 Input data Input nominal voltage range 2/3x 400 V AC ...
PAGE 7
QUINT-PS/3AC/24DC/20 Block diagram L1 (+) L2 L3 (-) DC OK I < IN PE 13 14 Safety notes DANGER OF EXPLOSION! Remove an item only when it is not connected to power or if it is located in the non-explosive area! DANGER Components with dangerously high voltage and high stored energy are located in the device! Never carry out work on live parts! Depending on the ambient temperature and the load, the housing can become very hot! WARNING Before startup please ensure: The mains connection has been carried out b
PAGE 8
QUINT-PS/3AC/24DC/20 Installation ATTENTION In order to ensure sufficient convection, we recommend a minimum vertical distance of 50 m to the other modules. A lateral distance of 5 mm, and in the case of active components, that of 15 mm is necessary for proper functioning of the module. Depending on the ambient temperature and the load of the module, the housing can become very hot! The power supply unit can be snapped onto all DIN rails as per EN 60715; it can also be mounted on walls.
PAGE 9
QUINT-PS/3AC/24DC/20 A Slim-style installation B Assembly: Position the module with the DIN rail guide on the upper edge of the DIN rail, and snap it in with a downward motion. Removing: Pull the snap lever open with the aid of a screwdriver and slide the module out at the lower edge of the DIN rail. B A Low-profile installation Low-profile installation can be achieved by mounting the device at right-angles to the DIN rail. Mount the DIN rail adapter (UTA 107/30) as described in the figure.
PAGE 10
QUINT-PS/3AC/24DC/20 Connection to various systems TN-S TN-C TT L1 L2 L3 N PE L1 L2 L3 PE + - iT L1 L2 L3 PEN L1 L2 L3 PE + - L1 L2 L3 N L1 L2 L3 PE + - L1 L2 L3 L1 L2 L3 PE + - The connection for 3x 400 V AC ... 500 V AC is established using the L1, L2, L3 and PE screw connections. The device can be connected to a 3-phase system with nominal voltages of 3x 400 V AC ... 500 V AC. In the event of a phase failure, unrestricted operation is possible with nominal capacity.
PAGE 11
QUINT-PS/3AC/24DC/20 Output ATTENTION Make sure that all output lines are dimensioned according to the maximum output current or are separately protected. The cables on the secondary side must have sufficiently large cross sections in order to keep the voltage drops on the lines as low as possible.
PAGE 12
QUINT-PS/3AC/24DC/20 Floating contact 13 DC OK Output 24 V DC 14 max. 30 V AC/DC 1A + + - - - The floating signal contact opens and indicates that the set output voltage has undershot by more than 10%. Signals and ohmic loads of up to maximum 30 V and currents of maximum 1 A (or maximum 60 V with maximum 0.5 A) can be switched. For heavily inductive loads such as a relay, a suitable protection circuit (e.g. damping diode) is necessary.
PAGE 13
QUINT-PS/3AC/24DC/20 Function UOUT [V] Output characteristic curve I < IN UN I > IN U < 0,9 x UN IN IBOOST IOUT [A] The power supply unit operates with the static POWER BOOST power reserve as per the U/I characteristic curve given in the figure. In case of ambient temperatures Tamb < +40°C, IBOOST is available permanently; it is available only for a few minutes in case of higher temperatures. In the event of a secondary short circuit and overload, the output current is limited to IBOOST.
PAGE 14
QUINT-PS/3AC/24DC/20 Parallel operation Devices of the same type can be connected in parallel to enable both redundancy and an increase in efficiency. No other alignment is necessary when in the state of delivery. If the output voltage is adjusted, a uniform distribution of power is guaranteed by setting all parallel operated power supply units to exactly the same output voltage.