Datasheet

ManualsBrandsPHOENIX CONTACT ManualsRack & DIN Rail Mount PSUsRail mounted PSU (DIN) QUINT-PS/1AC/48DC/10 48 Vdc 10 A 480 W 1 x

1Description

Primary-switched power supply with SFB

technology, 1 AC, output current 10 A

QUINT-PS/ 1AC/48DC/10

Data Sheet

INTERFACE

QUINT POWER power supply units – highest system

availability due to SFB technology

Compact power supply units of the new QUINT POWER

generation maximize the availability of your system. Even the

standard power circuit-breakers can be tripped reliably and

quickly with the SFB technology (Selective Fusebreaking

Technology) and six times the nominal current for 12 ms.

Defective current paths are disconnected selectively, the

defect is limited and the important system parts remain in

operation. A comprehensive diagnostics is carried out by

continuously monitoring the output voltage and current. This

preventive function monitoring visualizes the critical

operating modes and reports them to the control unit before

an error occurs.

DANGER OF EXPLOSION!

Only remove equipment when it is disconnected and not in the potentially explosive area.

DANGER

The device contains dangerous live elements and high levels of stored energy.

Never carry out work when the power is turned on.

Make sure you always use the latest documentation.

It can be downloaded at www.phoenixcontact.net/download

– Quick tripping of standard power circuit breakers with

dynamic SFB technology power reserve

– Reliable starting of difficult loads with static POWER

BOOST power reserve

– Preventive function monitoring

– Can be used worldwide

– High degree of operational safety due to high MTBF >

500 000 h, long mains buffering times > 20 ms, high

dielectric strength up to 300 V AC

103381_en_02

Features

Summary of content (14 pages)

PAGE 1
QUINT-PS/ 1AC/48DC/10 Primary-switched power supply with SFB technology, 1 AC, output current 10 A INTERFACE Data Sheet 103381_en_02 1 © PHOENIX CONTACT - 03/2009 Description QUINT POWER power supply units – highest system availability due to SFB technology Compact power supply units of the new QUINT POWER generation maximize the availability of your system.
PAGE 2
QUINT-PS/ 1AC/48DC/10 2 Table of contents 1 Description ..................................................................................................................................1 2 Table of contents.........................................................................................................................2 3 Ordering data ..............................................................................................................................3 4 Technical data............
PAGE 3
QUINT-PS/ 1AC/48DC/10 3 Ordering data Description Type Order No. Pcs. / Pkt. Primary-switched power supply with SFB technology, 1 AC, output current 10 A QUINT-PS/ 1AC/48DC/10 2866682 1 Accessories Type Order No. Pcs. / Pkt. Universal wall adapter UWA 182/52 2938235 1 4 Technical data Input data Input nominal voltage range 100 V AC ... 240 V AC AC input voltage range 85 V AC ... 264 V AC Short-term input voltage 300 V AC DC input voltage range 90 V DC ...
PAGE 4
QUINT-PS/ 1AC/48DC/10 DC OK active Output description UOUT > 0.9 x UN: High signal Voltage + 24 V DC Current ≤ 20 mA (short circuit resistant) Status display "DC OK" LED green / UOUT < 0.9 x UN: LED flashing DC OK floating Output description Relay contact, UOUT > 0.9 x UN: Contact closed Voltage ≤ 30 V AC/DC (≤ 0.5 A / at 60 V AC/DC) Current ≤1A Status display "DC OK" LED green / UOUT < 0.
PAGE 5
QUINT-PS/ 1AC/48DC/10 Standards (Continued) Limitation of mains harmonic currents EN 61000-3-2 Device safety GS (tested safety) Network variants (undervoltage) Semi F47-200 Certificate CB Scheme Approvals UL approvals UL applied for Conformance with EMC guideline 2004/108/EC and for low-voltage guideline 2006/95/EC Noise immunity according to EN 61000-6-2 Electrostatic discharge Electromagnetic HF field EN 61000-4-2 Housing Level 4 Contact discharge 8 kV Discharge in air 15 kV Comments C
PAGE 6
QUINT-PS/ 1AC/48DC/10 5 Structure 9 5 13 4 DC OK QUINT POWER 3 Sig nal 14 I< IN 1 2 3 4 5 6 7 8 9 AC input DC output POWER BOOST switching output, active DC OK switching output active DC OK output, floating Potentiometer 30 V DC ... 56 V DC "DC OK" LED "BOOST" LED Universal DIN rail adapter UTA 107/30 Bo ost DC OK Inp ut AC L 30 -56 100 -2 N 40 V V PE Ou tp + ut DC + 48 V 1 - 10 A - - 2 6 7 8 Input Output Signal [mm2] solid stranded 0.2 - 6 0.2 - 4 0.2 - 6 0.2 - 4 0.2 - 6 0.
PAGE 7
QUINT-PS/ 1AC/48DC/10 6 Block diagram L (+) active PFC N (-) PE DC OK I < IN 13 14 7 Safety notes DANGER OF EXPLOSION! Only remove equipment when it is disconnected and not in the potentially explosive area. DANGER The device contains dangerous live elements and high levels of stored energy. Never carry out work when the power is turned on.
PAGE 8
QUINT-PS/ 1AC/48DC/10 8 Installation ATTENTION Sig 14 nal DC OK QUINT POWER 13 In order to ensure sufficient convection, we recommend a minimum vertical distance of 5 cm to the other modules. A lateral distance of 5 mm, and in the case of active components, that of 15 mm is necessary for proper functioning of the module. Depending on the ambient temperature and the load of the module, the housing can become very hot! I< IN Bo ost The power supply unit can be snapped onto all DIN rails in acc.
PAGE 9
QUINT-PS/ 1AC/48DC/10 10 Mounting on DIN rails A Slim-style installation B Assembly: Position the module with the DIN rail guide on the upper edge of the DIN rail, and snap it in with a downward motion. Removing: Pull the snap lever open with the aid of a screwdriver and slide the module out at the lower edge of the DIN rail. B A Low-profile installation Low-profile installation can be achieved by mounting the device at right-angles to the DIN rail.
PAGE 10
QUINT-PS/ 1AC/48DC/10 11 Connection to various systems TN-S L N PE TN-C L N PE L N PE + − TT L N PE + − L1 L2 L3 N PE L N PE L PEN L PEN L N PE + − + − L N PE + − L1 L2 L3 PEN iT L1 L2(N) + − L1 L2 L3 N L N PE + − L1 L2 L3 L N PE + − The connection for 100 V AC ... 240 V AC is established using the L, N, and P screw connections.
PAGE 11
QUINT-PS/ 1AC/48DC/10 13 Output CAUTION Make sure that all output lines are dimensioned according to the maximum output current or are separately protected. The cables on the secondary side must have sufficiently large cross sections in order to keep the voltage drops on the lines as low as possible.
PAGE 12
QUINT-PS/ 1AC/48DC/10 Floating contact 13 DC OK Output 48 V DC 14 max. 30 V AC/DC 1A (60 V AC/DC 0,5 A) + + - - - The floating signal contact opens and indicates that the set output voltage has undershot by more than 10%. Signals and ohmic loads of up to maximum 30 V and currents of maximum 1 A (or maximum 60 V with maximum 0.5 A) can be switched. For heavily inductive loads such as a relay, a suitable protection circuit (e.g. damping diode) is necessary.
PAGE 13
QUINT-PS/ 1AC/48DC/10 15 Function UOUT [V] Output characteristic curve I < IN UN I > IN U < 0,9 x UN IN IBOOST IOUT [A] The power supply unit operates with the static POWER BOOST power reserve as per the U/I characteristic curve given in the figure. In case of ambient temperatures Tamb < +40°C, IBOOST is available permanently; it is available only for a few minutes in case of higher temperatures. In the event of a secondary short circuit and overload, the output current is limited to IBOOST.
PAGE 14
QUINT-PS/ 1AC/48DC/10 Parallel operation Devices of the same type can be connected in parallel to enable both redundancy and an increase in efficiency. No other alignment is necessary when in the state of delivery. If the output voltage is adjusted, a uniform distribution of power is guaranteed by setting all parallel operated power supply units to exactly the same output voltage.