Datasheet

ManualsBrandsPHOENIX CONTACT ManualsElectronic Control SystemsRepeater power supply MINI MCR-SL-RPS-I-I

1Description

Repeater power supply, active

MINI MCR-SL-RPS-I-I

Data sheet

The 6.2mm wide MINI MCR-SL-RPS-I-I... repeater power

supply supplies transmitters in the field and electrically iso-

lates the input signal from the output signal. The module can

be used in both isolator and repeater power supply operation.

Electrically isolated 0...20 mA or 4...20 mA standard analog

signals are available on the input and output side.

Power (19.2 V DC to 30 V DC) can be supplied either via the

connection terminals on the modules or in

conjunction with the DIN rail connector.

Features

– 0...20mA or 4...20mA input and output signal range

– Approval for Ex-zone 2 (nA)

– Supply to passive sensors and transmitters

– Screw or spring-cage connection can be provided

Attention: Correct usage in potentially explosive areas

The module is a category 3 item of electrical equipment. It is absolutely vital to follow the instructions provided

here during installation and observe the information in the "Safety regulations and installation notes".

Make sure you always use the latest documentation.

It can be downloaded from the product at www.phoenixcontact.net/catalog

This data sheet is valid for all products listed on the following page:

101947_en_07

2011-12-20

Summary of content (8 pages)

PAGE 1
MINI MCR-SL-RPS-I-I Repeater power supply, active Data sheet 101947_en_07 1 © PHOENIX CONTACT 2011-12-20 Description The 6.2 mm wide MINI MCR-SL-RPS-I-I... repeater power Features supply supplies transmitters in the field and electrically iso– 0...20 mA or 4...20 mA input and output signal range lates the input signal from the output signal. The module can – Approval for Ex-zone 2 (nA) be used in both isolator and repeater power supply operation.
PAGE 2
MINI MCR-SL-RPS-I-I 2 Table of contents 1 Description .............................................................................................................................. 1 2 Table of contents ..................................................................................................................... 2 3 Ordering data .......................................................................................................................... 3 4 Technical data .....................
PAGE 3
MINI MCR-SL-RPS-I-I 3 Ordering data Description Type Order No. Pcs. / Pkt. MCR repeater power supplies, screw connection, input signal: (0)4..20 mA, output signal: (0)4..20 mA MINI MCR-SL-RPS-I-I 2864422 1 MCR repeater power supplies, spring-cage connection, input signal: (0)4..20 mA, output signal: (0)4..20 mA MINI MCR-SL-RPS-I-I-SP 2864752 1 Accessories Type Order No. Pcs. / Pkt. DIN rail connector (TBUS), 5-pos., for bridging the supply voltage, can be snapped onto NS 35/...
PAGE 4
MINI MCR-SL-RPS-I-I Supply Nominal supply voltage 24 V DC Supply voltage range 19.2 V DC ... 30 V DC (to bridge the supply voltage, the DIN rail connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, Order No. 2869728) can be used. It can be snapped onto a 35 mm DIN rail according to EN 60715) Power consumption < 900 mW (at 24 V DC and in repeater power supply operation) < 600 mW (at 24 V DC and in isolator operation) General data Limit frequency (3 dB) Approx. 100 Hz Transmission error, typical ≤ 0.
PAGE 5
MINI MCR-SL-RPS-I-I 5 Safety regulations and installation notes 5.1 Installation notes – – – – – The category 3 device is suitable for installation in the zone 2 potentially explosive area. It fulfills the requirements of EN 60079-0:2009 and EN 60079-15:2010. Installation, operation, and maintenance may only be carried out by qualified electricians. Follow the installation instructions described.
PAGE 6
MINI MCR-SL-RPS-I-I 6.3 6 Installation 6.1 Connection notes Block diagram Attention: Electrostatic discharge! OUT I The device contains components that can be damaged or destroyed by electrostatic discharge. When handling the device, observe the necessary safety precautions against electrostatic discharge (ESD) according to EN 613405-1 and EN 61340-5-2. 3-wire R- 64 ly 82 pp 32 I MC.: 28 o Su er MINd.–N ow Or rP ate e ld p / Fie Re F sor mA 40° Sen ..20 DC .+1 (4). 0V 4°.. : 0 ...
PAGE 7
MINI MCR-SL-RPS-I-I 6.5 Assembly Screw connection: B A B A D www.interface.phoenixcontact.com C E Figure 4 • • Figure 3 – 6.6 Insert the wire into the corresponding connection terminal block. Use a screwdriver to tighten the screw in the opening above the connection terminal block. Spring-cage connection: Mount the module on a 35 mm DIN rail according to EN 60715. When using the DIN rail connector, first place it into the DIN rail (see A – C). It is used to bridge the power supply.
PAGE 8
MINI MCR-SL-RPS-I-I 7 Connection/application example Actuator 4...20mA 1 2 PWR OUT GND1 3 4 IN I GND1 OUT I IN I 1 5 GND2 2 6 Control system UB + 7 GND3 MINI MCR-SL-RPS-I-I GND1 3 Control system GND1 4 8 PWR OUT 24V OUT I 5 UB GND2 6 UB + 7 GND3 8 24V MINI MCR-SL-RPS-I-I Mains voltage Mains voltage Figure 6 Repeater power supply operation with a passive Figure 8 sensor Isolator operation at the analog output module (0)4...