YM Y11+ E-SCOOTER USER MANUAL Website: www.yumeway.com Mail: support@yumeway.
CONTENTS Precautions for Riding .......................................... • Inspenction Before Riding.............................. • Safety Precautions......................................... 1 2 Product Description.............................................. • • • • Structure Parameter......................................... Structure Diagram............................................ Product Structure Size..................................... Product Packing List.................................
WARNING! Ø Please conduct a thorough inspection of your scooter before riding. Always wear protective gear. Ø Abide by local laws, regulations, and speed limits. INSPECTION BEFORE RIDING a) Turn on the control panel. b) Make sure the brakes work properly and brake pads are not worn excessively. c) Make sure the front of the scooter is stable and the stem is not loose. d) Make sure the seat is firmly attached. e) Check that the horn is working properly.
SAFETY PRECAUTIONS A. Always wear a helmet,knee pads and elbow pads when riding. B. Use low speeds initially and gradually increase to higher speeds after as skills and confidence improve. C. Do not ride in the rain or through water puddles D. Children under the age of 16 should not be allowed on high performance scooters. E. Always check your brakes before starting your ride. F. Control and reduce speed when going downhill. Large scooters are heavy and can carry significant momentum. G.
STRUCTURE PARAMETER PERFORMANCE Maximum Speed 50 Mph (80Km/h) Maximum Range 60 Miles (96km)* Motor Power 3000W*2 dual motor with hall sensor Speed Modes 3 Gears x 2 Drives Charging Time 6-7 hours Battery Capacity 60V 31.
STRUCTURE DIAGRAM 4
STRUCTURE SIZE 5
CHECK AFTER UNPACKING When The Scooter After Unpacking: 1. Check if there are YUME bag & tools. 2. Check if there are 2 chargers. 3. Check if there are two NFC key. 4. Check if there is a display. 5. Seat installation (if available). 6. Make sure the brake in good condition.
POLE UNFOLDING OPERATION Unfolding ① Press the silver snap in the direction of the arrow to completely remove the snap from the upper slot. ② Keep pressing the silver snap and push the lever in the direction of the arrow. ④ Push back the red folding stick and restore the pole. ③ After the silver snap clasps the lower slot, push back the red folding stick in the direction of the arrow.
SCOOTER ASSEMBLY Handlebar Installation 1 2 1. Take out the handlebar, align it with the pole and place it in a suitable position. 2. Tighten the screws to hold firmly in place. 3 4 3. Take out the meter, loosen the two screws on the meter, and remove it. 4. Finally, align the display to the center of the handlebar, then tighten the screws to complete the installation process.
SCOOTER COMPONENTS SCOOTER ASSEMBLY Command Centre Installation ① Check that the LCD control panel and display button screws are tight. ② Make sure the light switch,indicator light switch/horn and display switch screws are tight. ③ Check that the left and right brake lever screws are tight. ④ Check that the thumb throttle screws are tight.
GET TO KNOW THE HANDLEBAR OF YOUR E-SCOOTER LCD Display Turning Signal Button/Horn Display Button Headlight Button 10 Thumb Throttle
POLE FOLDING OPERATION Folding Folding Mechanism. ① Release the locking bar and press the silver lever in the direction of the arrow to completely remove the latch from the slot. ② Lower the stem in the direction of the arrow. ③ When the silver latch locks back in place in the folded position, folding is completed.
DISPLAY FUNCTION OPERATION Menu Description When the meter is turned on, the interface will display "- - - - ". Use the "M" and "F" buttons to adjust Unlock the number up or down and double-click the power power-on button to confirm each number of the password. The password default password is: 1111(YUME RIDE application setting can change the password ). NFC unlock & lock Menu setting a. After turning the scooter on, place the NFC key near the display's NFC sensor to automatically unlock the scooter.
DISPLAY BUTTON Button Name Function 【Power Button】 Press and hold the [power Button] for 3 seconds to switch on or off. Press the [Power Button] once to switch the display of MAX and AVG. Press the [Power Button] twice to switch the display units TRIP, TRIP TIME,Voltage. 【"M" Button】 Press the ["M" Button] once to cycle through speed modes/gears. 【"F" Button】 Press the ["F" Button] once to switch between single and dual motors drive.
DISPLAY INTERFACE 1：Function Icon Introduction Menu BLUETOOTH Description Bluetooth - A flashing icon indicates no connection. Steady blue icon represents a successful connection to your phone. BATTERY Battery meter - Battery levels are displayed in increments of 20%. When battery level falls below 10%, the last red bar flashes. MODE Current gear display - Press the "M" Button once to cycle between gears.
DISPLAY SPECIFICATION Model Display Specification u How to turn on/off the display: Use the included NFC key to turn the scooter on or off. u How to access the P setting: Long press "M" and "F" buttons at the same time to enter the P setting menu. u In P-Setting models: a. To cycle through the P Values within the P-Settings mode, press the "power button" to cycle through P01P08. Use the “M" button to increase and the "F" button decrease the parameters of each P value. b.
DISPLAY P-VALUE INTRODUCTION Menu Description Default P01 Voltage level: 48V, 60V,72V Default=60 P02 metric mile switching; 0: KM/H; 1: MPH Default=1 P03 Default shutdown time: Adjustable between 060min Default=5 P04 Wheel diameter: 8 - 22 inches Default=11 P05 Zero or non-zero start settings: 0 (zero start), 1 (non-zero start) Default=0 P06 Speed measuring magnetic steel number.The range is 0-255.
NFC KEY BINDING Ø Step 1: Mobile App Installation u To install the Android app, search for [YUME RIDE] in the App Gallery or scan the QR code below to install the app. u For Apple IOS system, you can search for [YUME RIDE] in the APP Store or scan the QR code below to install the app.
NFC KEY BINDING Ø Step 2: Turn on Bluetooth and GPS positioning u Turn on the GPS positioning/location settings on your mobile phone, Click on the Bluetooth icon on the upper left corner of the [YUME RIDE] application home page to open the Bluetooth scooter identification settings page. u Click YUME SCOOTER to connect your scooter. When prompted enter the password(The default six-digit password is 000000) to successfully connect with your phone.
NFC KEY BINDING Ø Step 3: “Add NFC” u Click to “Add NFC”. u Click “settings”. u Put the NFC key in the center of the display, and click the page to “Search”. u The display wil automatically search for NFC keys.
NFC KEY BINDING Ø Step 3: “Add NFC” u Click "Bind Card" to recognize your NFC key and bind it to your scooter. u You may then change the name of the NFC connection. Ø Step 4: NFC lock/unlock your scooter u When the scooter is turned on and detects the NFC key near the vehicle sensing area, the scooter is automatically locked/unlocked without a password. Remarks: Click “Add” to bind multiple NFC tags. Repeat the third step of NFC binding to bind other NFC keys.
RECHARGING OPERATION Charging 1.First insert aviation head to the charging port 2.Insert in socket NOTE: Ensure that the three-pin connector is precisely aligned with the charging socket. Failure to do so may cause a short circuit within the charging port. Recharging Battery a. Open the cover of charging port b. Insert the DC plug of power adapter to the charging port c. Insert AC plug of power adapter to wall socket. NOTE: a. Must use original Power adapter to recharge your E-scooter. b.
USAGE AND MAINTENANCE 1.Battery and charger a. b. c. The scooter is equipped with a dedicated Lithium battery and an intelligent charger. Please do not use another brand’s charge because it might not be suitable for the battery. The battery’s overall performance will change based on temperature, terrain, and weight of the user. During the winter, properly store the scooter with at least 75% battery capacity in room temperature. 2. Charger a.
USAGE AND MAINTENANCE 4. Brakes a. b. If you notice the braking performance deteriorating, check whether there is brake oil in the brake fluid reservoir or not. If there is none, do add it in order to get the brakes to the required sensitivity. If brake oil is added but the brake’s performance remains terrible, the brake pads might need urgent replacement. 5. Folding Parts a. When you feel the grip loosen, adjust the screw between the grip and the T-tube with a hex wrench. 6. Lubrication a.
GENERAL QUESTIONS SCOOTER CANNOT BE POWER ON a. b. c. d. Check whether the battery gets power or not. Open the foot pedal and check whether the issue is with the battery fuse. It might not be inserted properly or might have burnt out. Before closing the foot pedal, also check whether the main line between the electric scooter’s accelerator and controller is plugged in properly. Likewise, check whether the connector between the battery and the controller is plugged in properly or not.
GENERAL QUESTIONS Does Yume Have Scooter Warranty? How To Contact？ • We have after-sales service, please contact the dealer where you purchased from. • View more detaile warranty terms on the YUME official website. Please Attention Limited Warranty Does Not Cover: • Scooter malfunctioning caused by prolonged usage. • Unofficial modification of scooter and non-compliance with instructions. • Usage of scooter for commercial or competitive stunt. • Damage caused by removed screws using excessive force.
YUME SCOOTER SAFETY TIPS Who Should Ride A YUME Scooter? • • • The YUME product should not be ridden by anyone below the recommended age (18 years old). It is also recommended that you already have at least six months of two-wheel cycling experience. Endeavor to always wear a helmet, elbow and kneepads that meet the riders’ regulatory standards. Also, make sure to neatly tie the shoelaces to keep them out of the wheels’ way.
CONTACT US Technical support Team：support@yumeway.com If you have inquires please feel to contact us.
