YM-OSPREY E-SCOOTER USER MANUAL Website: www.yumeway.com Mail: support@yumeway.
CONTENTS Cycling Precautions .............................................. • Inspenction Before Riding.............................. • Safety Precautions......................................... 1 2 Product Description.............................................. • • • • Structure Parameter......................................... Structure Diagram............................................ Product Structure Size..................................... Product Packing List................................
WARNING! Ø Please conduct a thorough inspection of your scooter before riding should. Always wear protective gear. Ø Abide by local laws, regulations, and speed limits. INSPECTION BEFORE RIDING a) Make sure the control panel can be turned on. b) Make sure the brake handles work properly and brake pads are not worn out. c) Make sure the front of the scooter is stable and the stem is not loose. d) Make sure the seat is stable. e) Make sure the horn is working properly.
SAFETY PRECAUTIONS A. Be sure to wear a helmet,knee pads and elbow pads when riding. B. Use low speeds initially,then gradually increase to higher speeds after as skills and confidence improve. C. Do not ride in the rain or through water puddles D. Children under the age of 16 should not be allowed on high performance scooters. E. Always check your brakes before starting your ride. F. Control and reduce your speeds when going downhill. Large scooters are heavy and can carry significant momentum. G.
STRUCTURE PARAMETER PERFORMANCE Maximum Speed 60 Mph (96Km/h) Maximum Range 100 Miles (160km)* Motor Power 3500W*2 BLDC Dual Hub Motors Speed Modes 3 Gears x 2 Drives Charging Time 6-7 hour Battery Capacity 72V 40AH Samsung 50E cells Water Resistance IP54 Wheel Size 11" Tubeless Off-road Tire Hill Grade 35-45° (depending on rider's weight, hill slope and state of charge etc.
STRUCTURE DIAGRAM 4
STRUCTURE SIZE 5
CHECK AFTER UNPACKING When The Scooter After Unpacking: 1. Check if there are YUME bag & tools. 2. Check if there are 2 chargers. 3. Check if there are two NFC key. 4. Check if there is a display. 5. Seat installation (if available). 6. Make sure the brake in good condition.
POLE UNFOLDING OPERATION Unfolding ① Press the red lever in the direction of the arrow to completely remove the latch from the slot. ② Keep pressing the red lever and push the stem in the direction of the arrow. ③ After securely latching the folding lever, push the black locking bar in the direction of the arrow. ④ Make sure the lever and locking bar aer in the correct position and secure.
SCOOTER ASSEMBLY Handlebar Installation 1 2 1. Place the handlebar horizontally and align the center with the clamp. Cover the stem cover of the handlebar’s head. 2. Adjust to a comfortable position, and tighten the four screws on the handlebar. 3 4 3. Remove the two screws on the display. 4. Align the display with the center of the handlebar and tighten the screws to complete the assembly.
SCOOTER ASSEMBLY Command Centre Installation ① Check that the LCD control panel and display button screws are tight. ② Make sure the light switch, indicator light switch/horn and display switch screws are tight. ③ Check that the left and right brake lever screws are tight. ④ Check that the thumb throttle screws are tight.
SCOOTER ASSEMBLY Kickstand Installation ① OSPREY kickstand ② Remove the top two screws at the kickstand mounting location. ③ Align the kickstand with the screw holes, and tighten the screws. ④ Kickstand installation is now complete.
DAMPENER ASSEMBLY Install the Dampener 1 2 (1) Ensure that the scooter is pointing straight during the installation. (2) Loosen screws "a" on the dampener clamp "2" with a hex wrench, and slide the dampener "1" in. Place the dampener in the clamp as shown in the diagram but refrain from fastening the screw. Allow the dampener rod to freely slide for later adjustment. (3) Attach joint "b" on the dampener assembly to the bracket and fasten as shown.
DAMPENER ASSEMBLY Install the Dampener (4) While keeping the front straight, slide the center of the dampener rod so the exposed ends are equal in length. (5) Attach the dampener via the fixing bolt in "c". After aligning the dampener and making suitable adjustments, tighten bolt "a". (6) Check that the front wheel turns freely. Dampener installation is now complete.
CHARGING OPERATION 1. First, ensure that the two parts of the charger (i.e. the AC wall plug/power cord and the transformer) are firmly connected. 2. Next, locate the three-pin connector on one end of the charger. Open up the charging port’s cover to spot the charging hole. Align the three-pin connector with the pinholes and gently insert the cable. Once the connector reaches its maximum position, it connects to the scooter's charging port. The charger's groove should be aligned with the charging hole.
CHRGING&HANDLEBAR SECTION GET TO KNOW THE HANDLEBAR OF YOUR E-SCOOTER LCD Control Panel Turning Light Switch/Horn Display Button Light Switch 14 Index Finger Throttle
POLE FOLDING OPERATION Folding Folding Mechanism. ① Release the locking bar and press the red lever in the direction of the arrow to completely remove the latch from the slot. ② Lower the stem in the direction of the arrow. ③ When the red latch locks back in place in the folded position, folding is completed.
DISPLAY FUNCTION OPERATION Menu Description When the meter is turned on, the interface will display "- - - - ". Use the "M" and "F" buttons to adjust Unlock the number up or down and double-click the power power-on button to confirm each number of the password. The password default password is: 1111(YUME RIDE application setting can change the password ). NFC unlock & lock Menu setting a. After turning the scooter on, place the NFC key near the display's NFC sensor to automatically unlock the scooter.
DISPLAY BUTTON Button Name Function 【Power Button】 Press and hold the [Power Button] for 3 seconds to switch on or off. Press the [Power Button] once to switch the display of MAX and AVG. Press the [Power Button] twice to switch the display units TRIP, TRIP TIME,Voltage. 【"M" Button】 Press the ["M" Button] once to cycle through speed modes/gears. 【"F" Button】 Press the ["F" Button] once to switch between single and dual motors drive.
DISPLAY INTERFACE 1：Function Icon Introduction Menu BLUETOOTH Description Bluetooth - A flashing icon indicates no connection. Steady blue icon represents a successful connection to your phone. BATTERY Battery meter - Battery levels are displayed in increments of 20%. When battery level falls below 10%, the last red bar flashes. MODE Current gear display - Press the "M" Button once to cycle between gears.
DISPLAY SPECIFICATION Model Display Specification u How to turn on/off the display: Use the included NFC key to turn the scooter on or off. u How to access the P setting: Long press "M" and "F" buttons at the same time to enter the P setting menu. u In P-Setting models: a. To cycle through the P Values within the P-Settings mode, press the "power button" to cycle through P01P08. Use the “M" button to increase and the "F" button decrease the parameters of each P value. b.
DISPLAY P-VALUE INTRODUCTION Menu Description Default P01 Voltage level: 48V, 60V,72V Default=72 P02 metric mile switching; 0: KM/H; 1: MPH Default=1 P03 Default shutdown time: Adjustable between 060min Default=5 P04 Wheel diameter: 8 - 22 inches Default=11 P05 Zero or non-zero start settings: 0 (zero start), 1 (non-zero start) Default=0 P06 Speed measuring magnetic steel number.The range is 0-255.
NFC KEY BINDING Ø Step 1: Mobile App Installation u To install the Android app, search for [YUME RIDE] in the App Gallery or scan the QR code below to install the app. u For Apple IOS system, you can search for [YUME RIDE] in the APP Store or scan the QR code below to install the app.
NFC KEY BINDING Ø Step 2: Turn on Bluetooth and GPS positioning u Turn on the GPS positioning/location settings on your mobile phone, Click on the Bluetooth icon on the upper left corner of the [YUME RIDE] application home page to open the Bluetooth scooter identification settings page. u Click YUME SCOOTER to connect your scooter. When prompted enter the password(The default six-digit password is 000000) to successfully connect with your phone.
NFC KEY BINDING Ø Step 3: “Add NFC” u Click to “Add NFC”. u Click “settings”. u Put the NFC key in the center of the display, and click the page to “Search”. u The display wil automatically search for NFC keys.
NFC KEY BINDING Ø Step 3: “Add NFC” u Click "Bind Card" to recognize your NFC key and bind it to your scooter. u You may then change the name of the NFC connection. Ø Step 4: NFC lock/unlock your scooter u When the scooter is turned on and detects the NFC key near the vehicle sensing area, the scooter is automatically locked/unlocked without a password. Remarks: Click “Add” to bind multiple NFC tags. Repeat the third step of NFC binding to bind other NFC keys.
USAGE AND MAINTENANCE 1.Battery and charger a. b. c. The scooter is equipped with a dedicated Lithium battery and an intelligent charger. Please do not use another brand’s charge because it might not be suitable for the battery. The battery’s overall performance will change based on temperature, terrain, and weight of the user. During the winter, properly store the scooter with at least 75% battery capacity in room temperature. 2. Charger a.
4. Brakes a. b. If you notice the braking performance deteriorating, check whether there is brake oil in the brake fluid reservoir or not. If there is none, do add it in order to get the brakes to the required sensitivity. If brake oil is added but the brake’s performance remains terrible, the brake pads might need urgent replacement. 5. Folding Parts a. When you feel the grip loosen, adjust the screw between the grip and the T-tube with a hex wrench. 6. Lubrication a.
GENERAL QUESTIONS SCOOTER CANNOT BE POWER ON a. b. c. d. Check whether the battery gets power or not. Open the foot pedal and check whether the issue is with the battery fuse. It might not be inserted properly or might have burnt out. Before closing the foot pedal, also check whether the main line between the electric scooter’s accelerator and controller is plugged in properly. Likewise, check whether the connector between the battery and the controller is plugged in properly or not.
GENERAL QUESTIONS Does Yume Have Scooter Warranty? How To Contact？ • We have after-sales service, please contact the dealer where you purchased from. • View more detaile warranty terms on the YUME official website. Please Attention Limited Warranty Does Not Cover: • Scooter malfunctioning caused by prolonged usage. • Unofficial modification of scooter and non-compliance with instructions. • Usage of scooter for commercial or competitive stunt. • Damage caused by removed screws using excessive force.
YUME SCOOTER SAFETY TIPS Who Should Ride A YUME Scooter? • • • The YUME product should not be ridden by anyone below the recommended age (18 years old). It is also recommended that you already have at least six months of two-wheel cycling experience. Endeavor to always wear a helmet, elbow and kneepads that meet the riders’ regulatory standards. Also, make sure to neatly tie the shoelaces to keep them out of the wheels’ way.
CONTACT US Technical support Team：support@yumeway.com If you have inquires please feel to contact us.
