Xalio 300 UK master.qxd 25/03/03 13:08 Page 1 Handset display The display gives information about the operation of your telephone. On first use it is sometimes necessary to wait for a few minutes of charge before seing icons on the display. The meaning of the icons is the following : The battery is currently charging. The battery is full. The battery is low. Please charge. The handset receives an incoming call. There is a call in progress. The handset is within range of the base station.
Xalio 300 UK master.
Xalio 300 UK master.qxd 25/03/03 13:08 Page 3 Installing the Xalio 300 PLEASE CHARGE THE XALIO 300 FOR 24 HOURS BEFORE USE. ONLY USE RECHARGEABLE BATTERY PACK. Unpacking your Xalio 300 The Xalio 300 package contains : One Xalio 300 base station , One Xalio 300 handset One NiMH AAA 600 x 2 rechargeable battery pack PHILIPS , , 2,4 V One user guide , one warranty leaflet . If anything is missing, please contact your place of purchase immediately.
Xalio 300 UK master.qxd 25/03/03 Installing your Xalio 300 Plug the power supply unit into the wall socket. Plug the telephone line cord into the wall socket. 3 Open the battery door on the handset by sliding it down. 4 Connect the battery pack to the connector inside the handset. Place the battery with sticker face up and wires along the left side of the battery pack. When replacing the battery, only use NiMH. Optimal battery life is reached after 3 cycles of full charge / discharge.
Xalio 300 UK master.qxd 25/03/03 13:08 Page 5 Using the Xalio 300 Note : When using your telephone, 3 different beep types can be heard : a validation beep an error beep a programming invitation beep long press to come back on idle mode at any time To answer a call Press the Line key to answer the call. To end a call Press the Line key. Or Replace the handset on the base. To make a call Press the Line key. ABC GHI PQRS JKL TUV DEF MNO WXYZ Dial the number.
Xalio 300 UK master.qxd 25/03/03 13:08 Page 6 To store an entry in the phonebooks Press the Phonebook key once to open Phonebook 1 or press the Phonebook key twice to open Phonebook 2. ABC GHI PQRS JKL TUV DEF MNO WXYZ Enter the memory number (0 to 9) you want to give to this entry. Press the Programming key. ABC GHI PQRS JKL TUV DEF MNO WXYZ Enter the telephone number you want to store (up to 16 digits, including a pause by pressing the Transfer key).
Xalio 300 UK master.qxd 25/03/03 13:08 Page 7 To delete an entry Press the Phonebook key once to open Phonebook 1 or press the Phonebook key twice to open Phonebook 2. ABC GHI PQRS JKL TUV DEF MNO WXYZ Enter the memory number you want to delete. Press the Programming key twice. To call the last number (Redial) Press the Redial key. Display shows the last number called. Press the Line key.
Xalio 300 UK master.qxd 25/03/03 13:08 Page 8 Programming the Xalio 300 To set the ringer melody You can choose from 7 ringer melodies. Press the Programming key. Press the 1 key. ABC GHI PQRS DEF MNO JKL TUV WXYZ Enter your choice of melody 1, 2, ..., or 7. The selected melody is played. Press the Programming key to confirm your setting. To set the ringer volume You can choose from 3 ringer volumes. Press the Programming key. Press the 2 key.
Xalio 300 UK master.qxd 25/03/03 13:08 Page 9 To select Caller Display Type (country dependent*) To use the Caller Display function you must first subscribe to the Service from your Network operator. (See Note 1, 2 and 3 page 11). You can choose several types according to your country. The numeric display on your Xalio 300 does not show the name of the caller. Press the Programming key. Press the 0 key. ABC GHI PQRS JKL TUV DEF MNO WXYZ Select 1, 2, 3........
Xalio 300 UK master.qxd 25/03/03 13:08 Page 10 To select tone dialling (country dependent*) Press the Programming key. Press the Star key. Press the Programming key to confirm your setting. To select pulse dialling (country dependent*) This allows you to select pulse dialling (also called “Loop disconnect” and used in countries without DTMF tone dialling capability or using old PABX). Press the Programming key. Press the Hash key. Press the Programming key.
Xalio 300 UK master.qxd 25/03/03 13:09 Page 11 Troubleshooting PROBLEMS - No dialling tone when pressing - . icon is blinking. - When the handset is placed on the charging unit, no beep is heard. CAUSES SOLUTIONS - The base station is not properly connected to electricity or to the telephone sockets. - Check the connections.(p 4).
Xalio 300 UK master.qxd 25/03/03 13:09 Page 12 Environment and Safety Safety information The Xalio 300 is not designed for making emergency calls when the power fails. An alternative should be made available for making emergency calls. Power requirements The product requires an electrical supply of 220-240V, alternating monophased current, excluding IT installations defined in standard EN 60-950. WARNING The electrical network is classified as dangerous according to criteria in the standard EN 60-950.
