Video Cassette Recorder VRX463 Owner’s Manual I M P O R T A N T ! Return Your Warranty Registration Card Within 10 Days. See Why Inside.
Return your Warranty Registration card today to ensure you receive all the benefits you’re entitled to. Once your PHILIPS MAGNAVOX purchase is registered, you’re eligible to receive all the privileges of owning a PHILIPS MAGNAVOX product. So complete and return the Warranty Registration Card enclosed with your purchase at once. And take advantage of these important benefits.
Introduction 3 Welcome to your VCR owner’s manual. This manual has six sections: Setting Up Your VCR; Description of Controls; Basic Operations; Recording; Playing; and Information You May Need. The instructions explain all of the VCR’s features, which are listed below. You cannot hurt your VCR by trying the features! So read on – and relax.
Table of Contents Setting Up Your VCR Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Before Using Your VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Hookups Without a Cable Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before Using Your VCR 5 Putting Batteries in the Remote Control 1 To remove the battery compartment lid, push in the tab, then pull up the lid. 2 1 2 Place three AA batteries inside the battery compartment with their polarities (+ and – ends) aligned as indicated. 3 Replace the battery compartment lid. 3 Using the Remote Control • Point the remote control at the VCR’s remote sensor. • Do not put objects between the remote control and the VCR.
Hookups Without a Cable Box The basic VCR/TV connection – antenna/cable to VCR to TV – is shown below. If you have a Cable Box or a Digital Satellite System Receiver, please refer to pages eight-nine. After you hook up the VCR, please go to page 10 to turn on the VCR. 1 Disconnect the antenna or cable from your TV.
Hookups Without a Cable Box (cont’d) 7 3 Connect the RF coaxial cable (supplied) to the RF OUT Jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on type or screw-on type of coaxial cable, whichever you prefer. A snap-on type is supplied.) CABLE BOX IN OUT ANT.IN R AUDIO L VIDEO RF OUT CH3 CH4 Antenna or Cable CABLE BOX IN OUT 75V ANT CAB / LE ANT.
Hookups With a Cable Box/DSS Receiver This connection allows you to view any channel. After you connect the Cable Box/DSS Receiver, VCR, and TV as shown below, the features described on this page will be available. 1. Connect a Cable signal to the IN Jack 3. Use a second RF on the Cable Box/DSS Receiver. coaxial cable to connect the RF OUT 75V ANT ENN Jack on the VCR to A IN OUT IN the TV’s Antenna In jack. CABLE BOX IN OUT ANT.IN R AUDIO L VIDEO RF OUT CH3 CH4 2.
Hookups With a Cable Box/DSS Receiver (cont’d) 9 This connection allows you to program an unattended recording of more than one unscrambled channel and to watch one channel while recording another. After you connect the VCR, Cable Box/DSS Receiver, and TV as shown below, the features on this page will be available. 3. Use a second RF coaxial cable to con1. Connect a Cable nect the OUT Jack on the Cable Box/DSS signal to the VCR’s 75V Receiver to the TV’s ANTENNA IN Jack. ANT(enna) IN Jack.
Turning on Your VCR Before turning on your VCR, make sure there are batteries in the remote control. Details are on page five. Make sure the VCR, TV, and Cable Box/DSS Receiver (if applicable) are connected. Details are on pages six - nine. If you are going to set up the Controller now, connect the Controller before you begin. Details are on page 42. If you plan to set up the VCR Plus+ Programming System now, complete the charts on page 38 before you begin. 2 1 2 Turn on the TV.
Turning on Your VCR (cont’d) 11 6 Press the MENU button. The menu shown below will appear. 8 Wait for the VCR to program channels. CONNECT ANTENNA OR CABLE TO VCR THEN… PUSH CH UP KEY OR… FOR PLAY ONLY – PUSH STOP CBL/DSS 7 Press the CHANNEL Up button to begin automatic channel programming. AUTO SET PROCEEDING/PLEASE WAIT will appear on-screen.
Automatic Channel Programming Programming Channels Although your VCR may automatically memorize the channels you receive when you turn it on for the first time, this function lets you reprogram channels. Make each entry within one minute of the previous entry. 1 5 1 Press the VCR button, then press the MENU button to bring up the main menu display. Wait for the VCR to program channels. CBL/DSS PAUSE/STILL VCR POWER TV MUTE PLAY REW TO SELECT PUSH NO.
Automatic Channel Programming (cont’d) 13 Adding/Deleting Channels 1 1 2 Press the VCR button. CBL/DSS Press the MENU button to bring up the main menu display. TO SELECT PUSH NO. SHOWN 1 PROGRAM 2 VCR SET UP 3 TUNER SET UP 4 INPUT SELECT 5 SET CLOCK 6 SET REMOTE LOCATOR TO END PUSH EXIT 3 PAUSE/STILL VCR POWER TV MUTE PLAY REW EJECT 7 FF STOP F.ADV VCR PLUS+/ENTER EXIT/STATUS CLEAR MENU JOG/SHUTTLE VOL EL N CHAN 2 Press the Number 3 button to select TUNER SET UP. TO SELECT PUSH NO.
Setting the Clock There are four ways to set the VCR’s clock: Manually, with Time Zone Selection, with Manual PBS Channel Selection, or with Automatic PBS Channel Selection. Cable Box/DSS Receiver users must set the clock manually. Before you set the clock, make sure: • The VCR power is on. • The VCR light appears on the display panel. If it does not, press the VCR/TV button once. • Channels are programmed. Details are on page 12. • You make each entry within one minute of the previous entry.
Setting the Clock (cont’d) 15 Time Zone Selection 1 1 Press the VCR button, then press the MENU button. TO SELECT PUSH NO. SHOWN 1 2 3 4 5 6 PROGRAM VCR SET UP TUNER SET UP INPUT SELECT SET CLOCK SET REMOTE LOCATOR CBL/DSS 6 PAUSE/STILL VCR POWER TV MUTE PLAY REW FF TO END PUSH EXIT 2 EJECT STOP F.ADV VCR PLUS+/ENTER Press the Number 5 button to select SET CLOCK. CABLE BOX USERS SET CLOCK MANUALLY will appear on-screen briefly. Then, the menu shown below will appear.
Setting the Clock (cont’d) Manual PBS Channel Selection 1 2 1 Press the VCR button, then press the MENU button. CBL/DSS Press the Number 5 button to select SET CLOCK. CABLE BOX USERS SET CLOCK MANUALLY will appear on-screen briefly. Then, the menu shown below will appear. (If AUTO CLOCK is set to OFF, SET TIME ZONE will not be available.
Setting the Clock (cont’d) 17 Automatic PBS Channel Selection 1 2 1 Press the VCR button, then press the MENU button. CBL/DSS Press the Number 5 button to select SET CLOCK. CABLE BOX USERS SET CLOCK MANUALLY will appear on-screen briefly. Then, the menu shown below will appear. (If AUTO CLOCK is set to OFF, SET TIME ZONE will not be available.
Daylight-Saving Time Selection Daylight-Saving Time Selection Follow the steps below to program the VCR so its clock will automatically move forward one hour in April and turn back one hour in October. 1 CBL/DSS Press the VCR button, then press the MENU button to bring up the main menu display. PAUSE/STILL VCR POWER 1 TV MUTE PLAY REW TO SELECT PUSH NO. SHOWN 1 2 3 4 5 6 PROGRAM VCR SET UP TUNER SET UP INPUT SELECT SET CLOCK SET REMOTE LOCATOR TO END PUSH EXIT EJECT 4 FF STOP F.
Language Selection 19 Language Selection Follow the steps below to change the language of the on-screen displays. 1 CBL/DSS VCR 1 TV Press the VCR button, then press the MENU button. TO SELECT PUSH NO. SHOWN 1 2 3 4 5 6 PAUSE/STILL PROGRAM VCR SET UP TUNER SET UP INPUT SELECT SET CLOCK SET REMOTE LOCATOR 2 MUTE PLAY REW EJECT 5 TO END PUSH EXIT POWER FF STOP F.ADV VCR PLUS+/ENTER EXIT/STATUS CLEAR MENU JOG/SHUTTLE VOL NEL CHAN Press the Number 2 button to select VCR SET UP.
Remote Control Buttons VCR Button Press this button before pressing VCR operation buttons. CBL/DSS Button Press this button before pressing Cable Box or DSS Receiver operation buttons. PAUSE/STILL Button When in Record mode, press to temporarily stop the recording (pause). Press a second time to resume normal recording. Details are on page 31. When in Play mode, press once to freeze the picture (still). Press a second time to resume normal playback. Details are on page 56.
Remote Control Buttons (cont’d) 21 REW(ind) Button When in Stop mode, press to rewind the tape at high speed. During tape playback, press to rewind the tape while the picture stays on-screen. Details are on page 56. If you have a Magnavox or Philips TV, press to adjust (decrease) the picture controls. STOP Button Press to stop the tape. If you have a Magnavox or Philips TV, press to move down or backward one row or selection in the TV menu system. EJECT Button Press to eject the tape.
Display Panel VCR Display Panel Information about VCR operations appears here. Different information appears at different times. Cassette Compartment Insert a tape here. PLAY REW POWER PAUSE VCR/TV CHANNEL OTR VIDEO FF STOP/EJECT L AUDIO R VCR HQ SP AM SLP PM TIMER H M S ST REC SAP PLAY M PAUSE REC/OTR Hi- Fi Mode Lights These lights tell you the current operation of the VCR: REC(ord), PLAY, or PAUSE. VCR Light This light appears when the VCR is in VCR position.
Display Panel (cont’d) 23 Remote Sensor Receives a signal from your remote control so you can operate your VCR from a distance. Press the VCR button on the remote control before pressing other VCR operation buttons. OTR Light This light blinks when a one touch recording is in progress. Details are on page 32.
Front Panel FF (Fast Forward) Button When tape playback is stopped, press to fast forward the tape at high speed. During tape playback, press to fast forward the tape while the picture stays on-screen. Details are on page 56. PLAY Button Press to play a tape. Also, press to release Slow, Still, or Search mode and return to normal playback. Details are on page 56. REW(ind) Button When tape playback is stopped, press to rewind the tape at high speed.
Rear Panel 25 ANT(enna) IN Jack Connect your antenna or cable here. Details are on pages six - nine. AUDIO OUT Jacks Connect cables going to the AUDIO IN jacks of a camcorder, another VCR, or an audio source here. Details are on pages 47 and 50. CABLE BOX Jack Connect the Controller here. You may use the Controller with either a Cable Box or a DSS Receiver. Details are on pages 42 - 46. AUDIO IN Jacks Connect cables coming from the AUDIO OUT jacks of a camcorder, another VCR, or an audio source here.
Setting the Remote Control to Operate a TV Your VCR remote control may operate your TV. Follow these steps to set the remote control code. 1 Point the remote control at your TV. Press the TV button, then press the POWER button. If your TV turns on or off, try the CHANNEL Up/Down buttons. If your TV doesn’t turn on or off, or if the CHANNEL Up/Down buttons don’t work, go to step 2. If your TV does work, you’re finished. 2 2 4 1 Find the code for your TV. Repeat step 1.
Setting the Remote Control to Operate a Cable Box/DSS Receiver 27 Your VCR remote control may operate your Cable Box or DSS Receiver. Follow these steps to set the remote control code. 1 Turn on the Cable Box/DSS Receiver. Point the remote control at your Cable Box/DSS Receiver. Press the CBL/DSS button, then the POWER button. If your Cable Box/DSS Receiver turns off, try the CHANNEL Up/Down buttons.
On-Screen Status Displays An on-screen status display, which includes the current time, channel, and other information (see illustration of the status display at right), will appear when you press the EXIT/STATUS button or certain function buttons. The contents of the status display may vary. ON SCREEN ON: • Whenever you press the PLAY button or the STOP button, some of the contents of the status display will appear for five seconds.
Remote Locator 29 When you use the Remote Locator feature, your VCR can find your remote control. To find your remote, follow these steps. To program the VCR to find its remote control only.... 1 Press the POWER button on the VCR to turn on the VCR. LOCATING REMOTE appears on the TV screen briefly. Within a few seconds, the remote control will start beeping. It will beep for about 30 seconds.
Playing Read and follow the steps below to play a tape. 1 Turn on the TV and set it to channel 3 or 4, whichever the CH3/CH4 switch on the back of the VCR is set to. 2 Insert a tape in the VCR. The power will come on. The VCR will place itself in VCR position automatically (the VCR light will appear on the display panel of the VCR). If the VCR light does not appear, press the VCR/TV button once. If the tape’s record tab has been removed, playback will start automatically.
Recording 31 Read and follow the steps below to record a television program. 1 Turn on the TV and set it to channel 3 or 4, whichever the CH3/CH4 switch on the back of the VCR is set to. 2 Insert a tape with its record tab intact (details are on page five) in the VCR. The power will come on. 3 4 Press the VCR button. 1 2 3 8 9 Turn on the TV. Insert a tape. CBL/DSS PAUSE/STILL VCR POWER TV MUTE PLAY REW EJECT FF STOP F.
One Touch Recording The one touch recording (OTR) function allows you to start an immediate timed recording 30 minutes to nine hours long of the channel you are watching. Before you begin, make sure: • Channels are programmed. Details are on page 12. • The desired recording speed (SP or SLP) has been selected with the (Tape) SPEED button. Details are on pages 36 and 58. • There is a tape in the VCR.
Recording One Channel/Watching Another 33 1 2 Press the VCR button. Press the REC(ord)/OTR button to start a recording. Details are on page 31. 3 4 Press the VCR/TV button to put the VCR in TV position. The VCR light will disappear from the display panel. 6 PAUSE/STILL VCR POWER 1 TV MUTE PLAY REW 8 EJECT FF STOP F.ADV VCR PLUS+/ENTER EXIT/STATUS CLEAR MENU JOG/SHUTTLE Use the TV remote control to select the channel you want to watch.
Timer Recording Follow the steps below to program your VCR to record TV programs while you’re away from home. You can program up to eight timer recordings. For each one, the VCR will turn itself on, record, and turn itself off automatically. Before you begin make sure: • Channels are programmed. Details are on page 12. • The clock is set. Details are on pages 14 - 17. • There is a tape in the VCR. Make sure the tape’s record tab is intact and the tape is long enough to record the program(s).
Timer Recording (cont’d) 35 4 Use the Number buttons (1 - 8) to select a slot in which to store the timer recording. Flashing numbers indicate an open slot (one in which a timer recording has not yet been stored). NOTE: If you select a number that has already been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on-screen briefly. Then information about the program in that slot will appear. If this happens, press the EXIT/STATUS button. Start again at step 1.
Timer Recording (cont’d) 8 Press the Number 1 button to record in SP speed. Press the Number 2 button to record in SLP speed. You cannot use the (Tape) SPEED button at this time. ONE TIME PROGRAM PROGRAM 1 CHANNEL 10 CABLE/TV TIME ON 09:30 PM TIME OFF 11:00 PM REC SPEED SLP SP=1 SLP=2 TO CORRECT PUSH CLEAR TO END PUSH EXIT 9 Press two Number buttons for the month and two Number buttons for the day you want the program to record. For example, for July 10, press 07, 10.
Timer Recording (cont’d) 37 Checking or Clearing Timer Recordings 1 2 1 Press the VCR button. CBL/DSS PAUSE/STILL Make sure the VCR is in VCR position. (The VCR light will appear on the display panel.) If the VCR light does not appear, press the VCR/TV button once. 3 4 5 Press the MENU button. VCR POWER TV MUTE PLAY REW EJECT FF STOP F.ADV VCR PLUS+/ENTER 8 EXIT/STATUS CLEAR MENU JOG/SHUTTLE VOL NEL CHAN 7 3 Press the Number 1 button to select PROGRAM.
Setting Up the VCR Plus+ Programming System 1 First, fill in the boxes on this page. It will only take a few minutes, and you must do it if you want the VCR Plus+ programming system to work properly. Since the channel numbers of the stations you receive may not be the same as the station numbers, and since channel numbers differ from area to area, you must program the VCR with your local channel information.
Setting Up the VCR Plus+ Programming System (cont’d) 39 2 Now, compare the channel numbers you have written into the VCR PLUS+ CH. and CABLE/TV CH. columns. You’ll notice that some stations have VCR Plus+ and Cable/TV channel numbers that are the same, and other stations have channel numbers that do not match. Where the channel numbers DO NOT match, you must tell the VCR the VCR Plus+ and Cable/TV channel numbers according to the following steps.
Timer Recording With the VCR Plus+ Programming System Follow the steps below to program a timer recording using PlusCode programming numbers. Before you begin make sure: • Channels are programmed. Details are on page 12. • The clock is set. Details are on pages 14 - 17. • There is a tape in the VCR. Make sure the tape’s record tab is intact and the tape is long enough to record the program(s). • The VCR is in VCR position (the VCR light will appear on the display panel of the VCR).
Timer Recording With the VCR Plus+ Programming System (cont’d) 41 5 Press the Number 1 button to record in SP speed or the Number 2 button to record in SLP speed. You cannot use the (Tape) SPEED button at this time. ONE TIME PROGRAM PROGRAM 2 CHANNEL 25 CABLE/TV TIME ON 10:00 AM TIME OFF 01:00 PM REC SPEED SLP START DATE 07/10/97 THU. PUSH 1=SP OR 2=SLP TO END PUSH EXIT 6 Press the EXIT/STATUS button. PROGRAM WAS COMPLETED/PLEASE TURN OFF VCR FOR TIMER RECORDING should appear on the screen.
Connecting the Controller If you are using a Cable Box or DSS Receiver, connect the Controller to your VCR. The Controller will automatically select channels at the Cable Box or DSS Receiver during a timer recording. Leave your Cable Box or DSS Receiver turned on during a timer recording. 1 Connect the Cable Box or DSS Receiver to the VCR as shown below. For more information, please read page eight. Or, refer to the owner’s manual of your Cable Box or DSS Receiver.
Setting the Controller to Operate a Cable Box 43 • If you use a Cable Box, you must set the clock manually. Details are on page 14. • Complete the steps on page 27 before proceeding. This will enable you to use the VCR remote control to operate the Cable Box, and you will learn your Cable Box code. • Make each entry within one minute of the previous entry. 1 2 3 1 Turn on the Cable Box. Set it to a channel other than channel 09. CBL/DSS Turn on the Cable Box. Select a channel other than 09.
Setting the Controller to Operate a Cable Box (cont’d) 7 Use the Number buttons to enter the two-digit code for your Cable Box. (See list below.) SELECT CODE NUMBER OF YOUR CABLE BOX 02 TO TEST PUSH MENU CBL/DSS DID CABLE BOX CHANGE TO CHANNEL 09? 1 YES 2 NO PAUSE/STILL VCR POWER TV MUTE PLAY REW FF TO END PUSH EXIT CABLE BOX/DSS RECEIVER CODES EJECT STOP F.ADV VCR PLUS+/ENTER GENERAL INSTRUMENTS . . .01, 02, 03, 04, 05, 06, 07 HAMLIN . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Controller to Operate a DSS Receiver 45 • If you use a DSS Receiver, you must set the clock manually. Details are on page 14. • Complete the steps on page 27 before proceeding. This will allow you to use the VCR remote control to operate the DSS Receiver, and you will learn your DSS Receiver code. 1 1 Turn on the DSS Receiver. Select a channel other than 205. CBL/DSS Turn on the DSS Receiver; select a channel other than 205 at the DSS Receiver.
Setting the Controller to Operate a DSS Receiver (cont’d) 6 Press the MENU button. SELECT OUTPUT CH OF YOUR DSS RECEIVER CBL/DSS VCR TV 0PAUSE/STILL TO END PUSH EXIT POWER MUTE PLAY REW 7 EJECT A zero will appear in the SELECT OUTPUT CH menu. Press one Number button (3 or 4) to complete the output channel of your DSS Receiver (channel 03 or 04). • Press 0 if you connected the VIDEO/AUDIO OUT Jacks of the DSS Receiver to the VCR’s VIDEO/AUDIO IN Jacks.
Rerecording (Tape Duplication) 47 The instructions on this page show you how to copy tapes. Different VCRs may operate differently. To duplicate a tape, make the connections shown, then follow steps 1 - 6. (You may use the AUDIO and VIDEO IN jacks on the front of VCR 2 instead if you prefer.) VCR 1 Playing VCR VCR 2 Recording VCR CABLE BOX IN OUT 3) Use an RF coaxial cable to connect the RF OUT Jack on VCR 2 to the TV’s ANTENNA IN Jack. CABLE BOX ANT.IN ANT.
Index Search When you make a recording, the VCR automatically places an index code at the beginning of the recording. Essentially, an index code is a type of “bookmark” for your tape. This feature is useful if you have several different programs recorded on a single tape. Fast forward or rewind to the next or previous index code on the tape by following the steps below. 1 2 3 1 Insert a tape. CBL/DSS PAUSE/STILL VCR POWER TV MUTE PLAY Press the VCR button.
Multi-Channel Television Sound System 49 If a tape is recorded in stereo, the VCR will play the tape in stereo. If a TV program is broadcast in stereo, the VCR will receive the program in stereo. (You must program the VCR and make the appropriate stereo hookups. Details are on pages 50 51.) Your VCR will do several additional things. • Second Audio You can program your VCR so that you can hear a program that is being broadcast in second audio or a tape that was recorded in second audio.
Multi-Channel Television Sound System (cont’d) To receive and record programs broadcast in second audio, follow steps 1 - 10. To record a program broadcast in stereo, make one of the connections shown, then follow steps 1 - 10. CABLE BOX IN OUT ANT.IN R AUDIO L VIDEO RF OUT CH3 CH4 CABLE BOX IN OUT ANT.IN R AUDIO L If you have a Stereo and a Monitor TV, use a video cable to connect the VCR’s VIDEO OUT Jack to the TV’s VIDEO IN Jack.
Hi-Fi Stereo Tape Playback 51 If a tape is recorded in Hi-Fi stereo, follow the steps below to play the tape in Hi-Fi stereo. 1 2 3 4 Press the VCR button, then press the MENU button. Press the Number 2 button to select VCR SET UP. Press the Number 7 button to select AUDIO OUT. Press the Number 1 button to select HIFI. (ON) will appear beside HIFI. 5 6 7 8 Press the EXIT/STATUS button. Press the MENU button. Press the Number 3 button to select TUNER SET UP.
Tape Counter Memory Using the Tape Counter Follow the steps below to reset the tape counter to zero at a tape location you want to refer to later. 1 CBL/DSS Play, fast forward, or rewind a tape to the location that you would like to refer to later. Press the STOP button to stop the tape. 2 5 PAUSE/STILL 3 2 POWER TV MUTE PLAY REW EJECT Press the EXIT/STATUS button. The status display, which includes the tape counter, will appear on-screen. VCR FF STOP F.
Go-To Feature 53 Follow the steps below to program the VCR to go to a place on a tape with a specified tape counter location number. • Make sure the VCR is in VCR position. (The VCR light will appear on the display panel. If it does not, press the VCR/TV button once.) 1 2 CBL/DSS 4 Press the VCR button. PAUSE/STILL VCR POWER TV MUTE PLAY REW EJECT When tape playback is stopped, press the GO-TO button to bring up the GOTO display. NOW GOTO 1 FF STOP F.
Repeat Playback Follow the steps below to program the VCR to play a tape over and over. 1 Press the VCR button, then press the MENU button. CBL/DSS VCR 1 TV TO SELECT PUSH NO. SHOWN 1 2 3 4 5 6 PROGRAM VCR SET UP TUNER SET UP INPUT SELECT SET CLOCK SET REMOTE LOCATOR PAUSE/STILL Press the Number 2 button to select VCR SET UP. REW EJECT 4 FF STOP Press the Number 1 button so that (ON) appears to the right of SET REPEAT PLAY.
Video Stabilizer 55 Video Stabilizer You can correct vertical vibration when playing back tapes recorded in SLP speed. When Video Stabilizer is ON, vertical vibration will be corrected automatically. Video Stabilizer is OFF when you receive the VCR. Follow the steps below to turn Video Stabilizer ON. CBL/DSS 1 PAUSE/STILL VCR POWER 1 TV MUTE PLAY Press the VCR button, then press the MENU button. REW FF TO SELECT PUSH NO.
Playback Options Forward and Reverse Searching 1 During tape playback, press and release the FF (Fast Forward) button or the REW(ind) button. A fast forward or reverse picture search will begin. 2 To return to playback, press the PLAY button. CBL/DSS PAUSE/STILL VCR POWER TV MUTE PLAY REW FF Viewing a Still Picture 1 EJECT EXIT/STATUS F.ADV CLEAR MENU During tape playback, press the PAUSE/STILL button. A still picture (frozen image) will appear on-screen.
Automatic Operation Features 57 Automatic Playback When you put a tape in the VCR, the power will come on automatically. If the tape’s record tab is missing, playback will begin. Automatic Rewind When a tape is played, fast forwarded, or recorded to its end, the VCR will rewind the tape to the beginning, then stop. If the Memory light appears on the display panel, the tape may stop at 0H00M00S on the tape counter.
Glossary AUDIO IN/OUT Jacks: jacks located on the front and back of the VCR which are used to record audio from another source (IN) or to send audio to another source (OUT). Automatic Channel Programming: process in which the VCR scans all available channels and places the ones you receive in its memory. Then, when you press the CHANNEL Up/Down buttons, you only scan through channels you receive. Bands: settings that allow you to tune channels.
Specifications 59 Video Heads Four heads with Hi-Fi stereo Video Signal EIA standards; NTSC color Antenna VHF/UHF – 75 ohm external antenna terminal VHF Output Signal Channel 03 or 04 (switchable) 75 ohms unbalanced Power Requirement 120V AC; 60 Hz Power Consumption 21W Operating Temperature 41°F (5°C) to 104°F (40°C) Relative Humidity 10% to 80% Weight 7.3 lbs. (3.3 kg.
Helpful Hints If you are having problems with your VCR, check the following list of problems and possible solutions before requesting service. You may be able to solve the problem yourself. The VCR has no power. • Make sure the power plug is completely connected to an AC (alternating current) outlet. • Make sure the power is turned on. A power failure occurred. • Select a language and program channels, if prompted to do so. Details are on pages 10 - 12 and 19. Reset the clock.
Helpful Hints (cont’d) 61 There is no playback picture, or the playback picture is noisy or contains streaks. • Make sure the TV is on the same channel as the VCR’s CH3/CH4 switch. Details are on pages six - nine. • Make sure the VCR is in VCR position. Details are on pages 21, 22, 24, and 33. • Make sure channel 3 or 4 is properly adjusted at the TV. • Adjust the tracking. Details are on page 57. The Number buttons won’t work for channels above 69; channels above 13 cannot be received.
Limited Warranty VIDEO CASSETTE RECORDER 90 Days Free Labor/One Year Parts Exchange. This product must be carried in for repair. WHO IS COVERED? You must have proof of purchase to receive warranty service. A sales receipt or other document showing that you purchased the product is considered proof of purchase. WHAT IS COVERED? Warranty coverage begins the day you buy your product. For 90 days thereafter, all parts will be repaired or replaced, and labor is free.
Index 63 ac power cord accessories ant(enna) in jack audio in/out jacks automatic playback rewind 25 64 6 - 9, 25 24 - 25, 47, 58 batteries 57 57 5 cable box connections 8-9 jack 25, 42 output channel 8-9 code 27, 44 cable/tv channels 38 - 39 cassette compartment 22 cassette-inside light 22 cbl/dss button 20 ch3/ch4 switch 25 channel above 100 20 adding 13 deleting 13 display 23 programming 12 reviewing 13 up/down buttons 21, 24, 57 clear button 21, 52 clock display 23 setting 14-17 automatically 16 - 1
CB L/D US SS PA L R TIL VC E/S EW R PO TV ER W /S T IT AY EC PL EJ EX TE U FF U PL P TE O /EN ST S+ S R VC TU M TA LE C V D TT HU G/S JO U F.A R L EN M VO AR LE CH AN NE L 1 4 2 7 5 0 10 C RE 3 8 TR /O 6 0 9 R VC G X KIN DE AC IN TR R. VA OW LOW SL S V /T D EE SP O -T GO M E T O O EM M R T A H R O C AR SE C O L IP SK E SUPPLIED ACCESSORIES Check to be sure the items on this page are packed with your VCR.
