Video Cassette Recorder VRX364AT TM Owner’s Manual I M P O R T A N T ! Return Your Warranty Registration Card Within 10 Days. See Why Inside.
Return your Warranty Registration card today to ensure you receive all the benefits you’re entitled to. Once your PHILIPS MAGNAVOX purchase is registered, you’re eligible to receive all the privileges of owning a PHILIPS MAGNAVOX product. So complete and return the Warranty Registration Card enclosed with your purchase at once. And take advantage of these important benefits.
Introduction 3 Welcome to your VCR owner’s manual. This manual has seven sections: Setting Up Your VCR; Description of Controls; Basic Operations; Recording; Playing; Stereo Features; and Information You May Need. The instructions explain all of the VCR’s features, which are listed below.
Table of Contents Setting Up Your VCR Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Before Using Your VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Hookups Without a Cable Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before Using Your VCR 5 Putting Batteries in the Remote Control 1 1 2 2 3 3 Remove the battery compartment lid on the bottom of the remote control by pressing in the tab, then lifting the lid. Place two AA batteries inside the battery compartment with their polarities (+ and – ends) aligned as indicated. Replace the battery compartment lid. Using the Remote Control ● ● ● ● ● Point the remote control at the VCR’s remote sensor (see page 27) when using the remote control to operate the VCR.
Hookups Without a Cable Box The basic VCR/TV connection – antenna/cable to VCR to TV – is shown below. If you have a Cable Box or a Digital Satellite System, please refer to pages eight-nine. If you have a Stereo TV, please go to page 10. After you hook up the VCR, please go to page 11 to turn on the VCR. 1 Disconnect the antenna or cable from your TV.
Hookups Without a Cable Box (cont’d) 7 3 Connect the RF coaxial cable (supplied) to the OUT Jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on type (supplied) or screw-on type of coaxial cable, whichever you prefer.
Hookups With a Cable Box/Digital Satellite System This connection allows you to view any channel. After you connect the Cable Box/Digital Satellite System, VCR, and TV as shown below, the features described on this page will be available. 3. Use a second RF coaxial cable to connect the OUT Jack on the VCR to the TV’s ANTENNA IN Jack. 1. Connect a Cable signal to the IN Jack on the Cable Box/DSS receiver. IN OUT ANT AUDIO IN L IN OUT R OUT VIDEO OUT IN CH3 CH4 2.
Hookups With a Cable Box/Digital Satellite System (cont’d) 9 This connection allows you to program an unattended recording of more than one unscrambled channel and to watch one channel while recording another. After you connect the VCR, Cable Box/Digital Satellite System, and TV as shown below, the features on this page will be available. 2. Use an RF coaxial cable (supplied) to connect 1. Connect a Cable the OUT Jack on the VCR to the IN Jack on signal to the VCR’s the Cable Box/DSS Receiver.
Hookups With a Stereo TV antenna or cable to ANT(enna) IN Jack ANT AUDIO IN L IN OUT R OUT VIDEO OUT IN CH3 CH4 Audio and Video IN Jacks on TV VIDEO (yellow) and AUDIO (red and white) OUT Jacks Video Cable Audio Cable ● Audio and Video cables are not supplied. 1 Connect the antenna or cable to the ANT(enna) IN Jack on the back of the VCR. 2 Connect a video cable to the yellow VIDEO OUT Jack on the back of the VCR.
Turning on Your VCR 11 Before turning on your VCR, make sure there are batteries in the remote control and the VCR and TV are connected correctly. ● Follow the steps on this page only when you plug the VCR power cord into the wall outlet for the first time. ● You may not be able to program channels at step 5 if you are using a Cable Box. 2 1 Turn on the TV. POWER EJECT SLOW PAUSE/STILL PLAY 1 – REW F.FWD + STOP STATUS/EXIT Press the VCR button, then the POWER button. The VCR light and the PWR.
Channel Memory Programming Channels Although your VCR may automatically memorize the channels you receive when you turn it on for the first time, this function lets you reprogram channels. POWER EJECT SLOW PAUSE/STILL 1 2 Press the VCR button. PLAY – REW F.FWD + STOP 2 STATUS/EXIT CLEAR MENU SPEED REC/OTR Press the MENU button to bring up the main menu display. MEMORY JOG& SHUTTLE TO SELECT PUSH NO.
Channel Memory (cont’d) 13 Adding/Deleting Channels 1 2 3 4 POWER EJECT Press the VCR button. SLOW PAUSE/STILL PLAY – REW F.FWD Press the MENU button to bring up the main menu display. + STOP 7 STATUS/EXIT CLEAR 2 MENU SPEED MEMORY Press the Number 3 button to select TUNER SET UP. REC/OTR JOG& SHUTTLE Press the Number 4 button to select ADD/DELETE CH. SELECT CHANNEL NUMBER CH – – TO END PUSH EXIT 5 Use the Number buttons to enter the channel number.
Setting the Clock There are two ways to set the clock. With manual clock setting, you tell the VCR the current time. With automatic clock setting, the VCR gets the current time from your local PBS station. It keeps track of the time by constantly referring to the time broadcasted by your PBS station. If you are using a Cable Box or Digital Satellite System, you must set the clock manually.
Setting the Clock (cont’d) 15 5 POWER Press two Number buttons for the hour(s) and two Number buttons for the minute(s). Then press 1 for AM or 2 for PM. For example, for 2:15 PM, press 02, 15, 2. ● Enter a 0 before a single digit number. ● Entries that do not match the VCR’s internal calendar will cause a question mark (?) to appear on-screen. ● To make corrections, press the CLEAR button until the space for the number you want to correct is flashing. Then enter the correct number.
Setting the Clock (cont’d) Automatic Clock Setting 1 Press the VCR button, then press the MENU button to bring up the main menu display. 5 POWER EJECT SLOW PAUSE/STILL PLAY – TO SELECT PUSH NO. SHOWN 1 PROGRAM 2 VCR SET UP 3 TUNER SET UP 4 SET CLOCK REW F.FWD + STOP STATUS/EXIT CLEAR MENU SPEED MEMORY TO END PUSH EXIT REC/OTR 1 JOG& SHUTTLE 2 Press the Number 4 button to select SET CLOCK.
Setting the Clock (cont’d) 17 Time Zone When using the AUTO CLOCK function, you can specify a time zone in which a local PBS channel is located. That way, the VCR will update the clock according to your time zone. POWER SLOW 1 Press the VCR button, then press the MENU button to bring up the main menu display. TO SELECT PUSH NO. SHOWN 1 PROGRAM 2 VCR SET UP 3 TUNER SET UP 4 SET CLOCK EJECT PAUSE/STILL PLAY – REW F.
Daylight-Saving Time Selection Daylight-Saving Time Selection You may program the VCR so its clock will automatically move forward one hour in April and turn back one hour in October. Daylight-Saving Time is set to ON prior to shipment from the factory. You may turn Daylight-Saving Time ON or OFF by following the steps below. 1 2 Press the VCR button. POWER EJECT SLOW PAUSE/STILL PLAY – REW F.
Language Selection 19 Language Selection Follow the steps below to change the language of the on-screen displays. POWER 1 2 EJECT SLOW PAUSE/STILL PLAY Press the VCR button. – REW F.FWD + STOP STATUS/EXIT CLEAR MENU Press the MENU button to bring up the main menu display. SPEED TO SELECT PUSH NO. SHOWN 1 PROGRAM 2 VCR SET UP 3 TUNER SET UP 4 SET CLOCK REC/OTR MEMORY JOG& SHUTTLE 2 6 TO END PUSH EXIT 3 Press the Number 2 button to select VCR SET UP. TO SELECT PUSH NO.
Setting the Remote to Operate a TV Your VCR remote control may operate your TV. If the remote control doesn’t operate your TV now, follow the steps below to program your remote control. 1&6 2 1 POWER Find your TV code. EJECT SLOW Point the remote control at your TV and press the TV button. Then, press the POWER button. If your TV turns on or off, try the other TV buttons (see pages 22 - 24). If your TV doesn’t turn on or off, or if the other buttons don’t work, go to step 2.
Setting the Remote to Operate a Cable Box/Digital Satellite System 21 Your VCR remote control may operate your Cable Box or Digital Satellite System. If the remote control doesn’t operate your Cable Box or Satellite System now, follow the steps below to program your remote control. 1&6 2 POWER 1 EJECT SLOW Find your cable box code or satellite system code. PAUSE/STILL PLAY Point the remote control at your Cable Box or Satellite System and press the CBL/DSS button. Then, press the POWER button.
Remote Control Buttons EJECT Button When playback is stopped, press to eject the tape. POWER Button Press to turn on or off the VCR, TV, Cable Box, or Digital Satellite System. (You must first press the TV, VCR, or CBL/DSS button.) Details are on pages 20-21. PAUSE/STILL Button In Record mode, press to temporarily stop the recording (pause). Press a second time to resume normal recording. Details are on page 31. You can not pause a one touch recording that is set for a specific length of time.
Remote Control Buttons (cont’d) 23 F.FWD (Fast Forward) Button When in Stop mode, press to fast forward the tape at high speed. When in Play mode, press to fast forward while the picture stays onscreen. Details are on page 46. Or, if you have a Magnavox TV, press when in TV mode to adjust (increase) the picture controls in the TV menu system. SLOW Button During tape playback, press to view the picture in slow motion. Press a second time to resume normal playback.
Remote Control Buttons (cont’d) POWER EJECT SLOW PAUSE/STILL PLAY – REW F.FWD + STOP CLEAR Button Press to erase incorrect data when programming VCR functions. Also, press to reset the real time counter. Details are on page 45. STATUS/EXIT CLEAR MENU SPEED MEMORY Button Press to memorize a tape position at which the real time counter was set to 0:00:00. Details are on page 45. REC/OTR MEMORY JOG& SHUTTLE MUTE Button Press to eliminate the TV’s sound. Press again to restore the volume.
VCR Display Panel 25 Cassette Compartment Insert a tape here. VCR Display Panel Information about VCR operations appears here. STOP EJECT PLAY head REW PWR. w VIDEO L AUDIO R PAUSE PM CHANNEL VCR/TV Timer Light This light glows when you turn off the VCR when a timer recording has been set. It also glows when a one touch recording has been set. It flashes when you turn off the VCR if a timer recording has been set but a tape has not been placed in the VCR.
Front Panel PLAY Button Press to play a tape. Also, press to release Slow, Search or Still mode and to return to normal playback. Details are on pages 46-47. POWER Button Press to turn the VCR power on and off. STOP/EJECT Button Press once to stop the tape. When playback is stopped, press to eject the tape. STOP EJECT PLAY head REW PWR.
Front Panel (cont’d) 27 F.FWD (Fast Forward) Button When in Stop mode, press to fast forward the tape at high speed. When in Play mode, press to fast forward while the picture stays onscreen. Details are on page 46. REW(ind) Button When in Stop mode, press to rewind the tape at high speed. When in Play mode, press to rewind the tape while the picture stays on-screen. Details are on page 46. Remote Sensor Receives an infrared signal from your remote control so you can operate your VCR from a distance.
Rear Panel ANT(enna) IN Jack Connect your antenna or cable here. Details are on pages six-10. AUDIO IN Jacks Connect the cables coming from the AUDIO OUT Jacks of a camcorder, another VCR, or an audio source here. Details are on page 42. AUDIO OUT Jacks Connect the cables going to the AUDIO IN Jacks of a camcorder, another VCR, or an audio source here. Details are on pages 10, 42 and 50.
On-Screen Status Displays 29 A status display, which includes the current time, channel, and other information (see illustration), will appear when you press the STATUS/EXIT button or certain function buttons. The contents of the status display may vary. There are three status display modes: ON SCREEN ON: ● Whenever you press the STOP button or the PLAY button, the status display will appear for five seconds.
Playing 1 2 Read and follow the steps below to play a tape. 1 Turn the TV on and set it to channel 3 or 4, whichever the CH3/CH4 switch on the back of the VCR is set to. 2 Insert a tape in the VCR. The power will come on. The VCR will place itself in VCR position automatically (the VCR light and the Cassette-Inside light on the display panel of the VCR will appear). If the tape’s record tab has been removed, playback will start automatically. 3 Turn on the TV. Insert a tape in the VCR.
Recording 31 1 2 Read and follow the steps below to record a television program. 1 Turn the TV on and set it to channel 3 or 4, whichever the CH3/CH4 switch on the back of the VCR is set to. 2 Insert a tape with its record tab intact (see page five) in the VCR. The power will come on, and the Cassette-Inside light will appear. Turn on the TV. Insert a tape in the VCR. POWER 8 EJECT SLOW PAUSE/STILL PLAY – REW F.
Recording One Channel/Watching Another 1 2 3 Start a recording (see page 31). POWER SLOW PAUSE/STILL PLAY Press the VCR button. – REW F.FWD + STOP STATUS/EXIT CLEAR MENU Press the VCR/TV button to put the VCR in TV position. The VCR light will disappear from the VCR’s display panel. 4 EJECT SPEED 1 REC/OTR 8 MEMORY JOG& SHUTTLE Press the TV button, then press the CHANNEL (Up/Down) or Number buttons to choose the channel you want to watch.
One Touch Recording 33 The one touch recording (OTR) function allows you to program an immediate timed recording 30 minutes to eight hours long without setting the timer. Before you begin, make sure: ● Channels are programmed. ● The desired recording speed (SP, LP, or SLP) has been selected with the (Tape) SPEED button. ● There is a tape in the VCR. Make sure the tape’s record tab is intact and the tape is long enough to record the program(s). ● The VCR is in VCR position.
Timer Recording Follow the steps below to program your VCR to record TV programs while you’re away from home. You can program up to eight timer recordings. For each one, the VCR will turn itself on, record, and turn itself off automatically. Before you begin make sure: ● Channels are programmed. ● The clock is set. ● There is a tape in the VCR. Make sure the tape’s record tab is intact and the tape is long enough to record the program(s). ● The VCR is in VCR position.
Timer Recording (cont’d) 35 4 Use the Number buttons (1 - 8) to select a slot in which to store the timer recording. There are eight timer recording slots. Open slots will flash on-screen. NOTE: If you enter a number for a slot that has already been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear onscreen for a few seconds. Then information about the program in that slot will be displayed on-screen. If this happens, press the STATUS/EXIT button twice. Then start again at step 1.
Timer Recording (cont’d) 8 Press the Number 1 button to record in SP speed, press the Number 2 button to record in LP speed, or press the Number 3 button to record in SLP speed. (For details, see the chart below.) You cannot use the (Tape) SPEED button at this time. ONE TIME PROGRAM PROGRAM 1 CHANNEL 10 TIME ON 09:30 PM TIME OFF 11:00 PM REC SPEED SLP SP=1 LP=2 SLP=3 11 POWER EJECT SLOW PAUSE/STILL PLAY – 10 REW F.
Timer Recording (cont’d) 37 Checking or Cancelling Timer Recordings 1 POWER EJECT SLOW With the VCR on and in VCR position (the VCR light will appear on the display panel), press the VCR button, then press the MENU button. PAUSE/STILL PLAY – REW F.FWD + STOP 2 3 STATUS/EXIT CLEAR MENU SPEED MEMORY Press the Number 1 button to select PROGRAM. Press the Number 4 button to select PROGRAM REVIEW. The timer recording information for the program in the lowest numbered slot will appear on-screen.
Setting Up the VCR Plus+ Programming System 1 First, fill in the boxes on this page. It will only take a few minutes, and you must do it if you want the VCR Plus+ programming system to work properly. Since the channel numbers of the stations you receive may not be the same as the station numbers, and since channel numbers differ from area to area, you must program the VCR with your local channel information.
Setting Up the VCR Plus+ Programming System (cont’d) 39 2 Now, compare the channel numbers you have written in the VCR PLUS+ CH. and CABLE/TV CH. columns. You’ll notice that some stations have VCR Plus+ and Cable/TV channel numbers that are the same, and other stations have channel numbers that do not match. Where the channel numbers DO NOT match, you must tell the VCR the VCR Plus+ and Cable/TV channel numbers according to the following steps. ● Make each entry within 60 seconds of the previous entry.
Timer Recording With the VCR Plus+ Programming System Follow the steps below to program a timer recording using the PlusCode programming numbers in your TV guide. Before you begin, make sure: ● Channels are programmed (page 12). ● The VCR Plus+ and Cable/TV channel numbers are entered (pages 38 - 39). ● The clock is set (pages 14-17). ● There is a tape in the VCR. Make sure the tape’s record tab is intact and the tape is long enough to record the program(s).
Timer Recording With the VCR Plus+ Programming System (cont’d) 41 5 Press the Number 1 button to record in SP speed, the Number 2 button to record in LP speed, or the Number 3 button to record in SLP speed. Your selection will appear to the right of REC SPEED on-screen, although SP=1 LP=2 SLP=3 will continue to flash. For details about tape speed, see pages 36 and 56. You cannot use the (Tape) SPEED button at this time.
Rerecording (Tape Duplication) VCR 1 - Playing VCR VCR 2 - Recording VCR ANT AUDIO IN IN L IN IN OUT R R OUT VIDEO OUT ANT AUDIO L OUT IN CH3 CH4 OUT VIDEO OUT IN CH3 CH4 1. Audio cables from AUDIO OUT Jacks of VCR 1 to AUDIO IN Jacks of VCR 3. RF coaxial cable (supplied) from VCR’s OUT Jack to TV’s ANTENNA IN Jack 2. Video cable from VIDEO OUT Jack of VCR 1 to VIDEO IN Jack of VCR 2 ● Audio and Video cables are not supplied.
Repeat Playback 43 Repeat Playback Follow the steps below to program the VCR to play a tape over and over. 1 2 POWER SLOW PAUSE/STILL PLAY Press the VCR button. Press the MENU button to bring up the main menu display. EJECT – REW F.FWD + STOP 5 STATUS/EXIT CLEAR MENU SPEED TO SELECT PUSH NO. SHOWN 1 PROGRAM 2 VCR SET UP 3 TUNER SET UP 4 SET CLOCK REC/OTR 2 MEMORY JOG& SHUTTLE TO END PUSH EXIT 3 Press the Number 2 button to select VCR SET UP. TO SELECT PUSH NO.
Time Search Time Search Follow the steps below to program the VCR to search forward or backward a specific length of time. 1 2 Press the VCR button. POWER EJECT SLOW PAUSE/STILL 4 PLAY – REW F.FWD + STOP STATUS/EXIT CLEAR MENU Press the TIME SEARCH button to bring up the time search display. There must be a tape in the VCR.
Real Time Counter Memory 45 Real Time Counter Memory Follow the steps below to reset the real time counter to zero at a tape location you want to refer to later. POWER 1 SLOW PAUSE/STILL PLAY Play, fast forward, or rewind a tape to the location that you would like to refer to later. Press the STOP button to stop the tape.
Special Effects Playback Forward and Reverse Searching (SP/LP/SLP) 1 When in Play mode, press and release the F.FWD button or the REW(ind) button. A fast forward or reverse picture search will begin. POWER EJECT SLOW PAUSE/STILL PLAY – REW F.FWD + STOP 2 STATUS/EXIT CLEAR MENU SPEED MEMORY To return to playback, press the PLAY button. REC/OTR Super High Speed Searching (LP/SLP) JOG& SHUTTLE 1 When in Play mode, press the F.FWD button or the REW (ind) button, then press again.
Special Effects Playback (cont’d) 47 Viewing a Slow Motion Picture 1 When in Play mode, press the SLOW button. The tape will play in slow motion. NOTE: You can control the speed of slow motion playback by pressing the VAR(iable). SLOW buttons. POWER EJECT SLOW PAUSE/STILL PLAY – REW F.FWD + STOP STATUS/EXIT CLEAR MENU 2 SPEED To release Slow mode and return to normal playback, press the PLAY button or press the SLOW button again.
Automatic Operation Features The following playback features will always operate: Automatic Playback When you put a tape in the VCR, the power will come on automatically. If the tape’s record tab is missing, playback will begin. If a timer recording is set, the power will not come on automatically when you insert a tape with the record tab intact. If a timer recording is set and the VCR power is off, the VCR will eject the tape if the record tab is missing.
Automatic Operation Features (cont’d) 49 Manual Tracking To adjust the tracking manually, press the CHANNEL (Up/Down) buttons on the VCR during tape playback. NOTES: • This function is controlled only by the CHANNEL (Up/Down) buttons on the VCR. The CHANNEL (Up/Down) buttons on the remote control will not adjust tracking. • To return tracking to the position it was in when the VCR was shipped from the factory, press the CHANNEL (Up) and CHANNEL (Down) buttons on the VCR at the same time.
MTS Broadcast Stereo System Your VCR can play recordings broadcast in Hi-Fi (high fidelity) stereo, which produces a crisp, clear sound from two sources. Your VCR also can play tapes recorded in a second audio (usually, that means your program is recorded in a second language). Of course, your VCR will play tapes recorded in monaural (single-source) sound as well.
MTS Broadcast Stereo System (cont’d) 51 1 2 POWER EJECT Press the VCR button, then press the MENU button. SLOW PAUSE/STILL PLAY – REW F.FWD Press the Number 3 button to select TUNER SET UP. TO SELECT PUSH NO. SHOWN 1 TV 2 CABLE TV ON 3 AUTO PROGRAMMING 4 ADD/DELETE CH 5 CH MEMORY REVIEW 6 TV STEREO ON 7 2ND AUDIO TO END PUSH EXIT 3 + STOP 4 6 STATUS/EXIT CLEAR MENU SPEED REC/OTR MEMORY JOG& SHUTTLE Press the Number 6 button to select TV STEREO or the Number 7 button to select 2ND AUDIO.
Hi-Fi Stereo Sound System Multi-Channel Television Sound System broadcasts are automatically recorded in Hi-Fi stereo sound. To play in Hi-Fi stereo tapes recorded in Hi-Fi stereo, however, you’ll need to follow the steps below. 1 2 Press the VCR button, then press the MENU button. POWER EJECT SLOW PAUSE/STILL PLAY – 5 REW F.FWD + STOP STATUS/EXIT CLEAR MENU SPEED REC/OTR MEMORY JOG& SHUTTLE Press the Number 2 button to select VCR SET UP. TO SELECT PUSH NO.
Hi-Fi Stereo Sound System (cont’d) 53 6 7 POWER EJECT Press the MENU button to bring up the main menu display. SLOW PAUSE/STILL PLAY – REW F.FWD Press the Number 3 button to select TUNER SET UP. TO SELECT PUSH NO. SHOWN 1 TV 2 CABLE TV ON 3 AUTO PROGRAMMING 4 ADD/DELETE CH 5 CH MEMORY REVIEW 6 TV STEREO ON 7 2ND AUDIO TO END PUSH EXIT + STOP 9 STATUS/EXIT CLEAR MENU SPEED REC/OTR MEMORY 6 JOG& SHUTTLE 8 Press the Number 6 button to select TV STEREO.
Helpful Hints If you are having problems with your VCR, check the following list of problems and possible solutions before requesting service. You may be able to solve the problem yourself. No power • Make sure the power plug is completely connected to an AC (alternating current) outlet. • Make sure the power is turned on. Power Failure • Timer recordings and the clock setting may be lost if the power fails for more than one minute. See pages 14-17 to reset your clock.
Helpful Hints (cont’d) 55 TV programs cannot be watched normally. • Put the VCR in TV position. (Press the VCR/TV button so that the VCR light disappears from the display panel. For details see pages 22 and 27.) • Check the connections between the VCR, TV, antenna/cable, and Cable Box/Digital Satellite System (if applicable). (See pages six-10 for details.) Tape cannot be inserted. • Insert the tape, window side up, with the record tab facing you.
Glossary AUDIO IN/OUT Jacks: jacks located on the front and back of the VCR which are used to record audio from another source (IN) or to send audio to another source (OUT). Automatic Channel Programming: process in which the VCR scans all available channels and places the ones you receive in its memory. Then, when you push the CHANNEL (Up/Down) buttons, you only scan through channels you receive. Bands: settings that allow you to tune channels.
Specifications 57 Video Heads Four heads – Hi-Fi Video Signal EIA standards; NTSC color Antenna VHF/UHF – 75 ohm external antenna terminal VHF Output Signal Channel 3 or 4 (switchable) 75 ohms unbalanced Power Requirement 120V AC; 60Hz Power Consumption 20W Operating Temperature 41°F (5°C) to 104°F (40°C) Relative Humidity 10% to 80% Weight 6.17 lbs. (2.8 kg.
Limited Warranty VIDEO CASSETTE RECORDER 90 Days Free Labor/One Year Parts Exchange. This product must be carried in for repair. WHO IS COVERED? You must have proof of purchase to receive warranty service. A sales receipt or other document showing that you purchased the product is considered proof of purchase. WHAT IS COVERED? Warranty coverage begins the day you buy your product. For 90 days thereafter, all parts will be repaired or replaced, and labor is free.
Index 59 ac power cord.................................28 accessories .......................................60 ant(enna) in jack ...................6-10, 28 audio in/out jacks.............10, 26, 28, ..............................................42, 50, 56 automatic playback .......................................48 rewind, eject, off........................48 long play .....................................36, 56 lp ..................................................36, 56 memory button ...................
SUPPLIED ACCESSORIES Check to be sure the items on this page are packed with your VCR. These accessories are provided to help you use or set up your VCR. Remote Control 4835 218 37204 Two “AA” Batteries 4835 138 17012 RF Coaxial Cable, 75 ohm 4835 323 27011 If any of these items are not included, or if you need to replace an item, contact Philips Service Company at the address below. Philips Service Company P.O. Box 967 Greeneville, TN 37744-0967 Or, call 1-800-851-8885.
