o Programming with 'SHOW VIEW' All the information required for a programming is contained encoded in the SHOW VIEW-cade, € Switch on the TV set. © Press the [TEES] bunion on the remote contra, © Please enter the SHOW VIEW-code (up to 3 digits) printed in your TV guide next to the start time of a TV programmer.
OPERATING INSTRUCTIONS PHILIPS VR 675 Congratulations on the purchase of one of the most sophisticated and simple-to-use video recorders (VCB) on the market. With this VR you can record and play VHS-standard 1 cassettes, VHS Please take the time to read this operating manual before using your video recorder. Safety instructions and other notes Danger: High voyage! Do not open. The video recorder does not contain any components that can be repaved by the customer.
1. INSTALLATION Connecting cables EXT o Remove the aerial cable plug from your TV set and insert it into the LT ] socket at the back of the video recorder. 9 Plug one end of the aerial cable provided into the B Socket on the video recorder and the either end into the aerial input socket on your TV set. € 1 your television does not have a scary (AV-Euro) socket please do not read further here, but turn to Chapter 4, "SPECIAL FEATURES'.
T —— Emergency interrupt Automatic Channel Search Both the video recorder and the remote control have an ‘Emergency interrupt’ button. You can use the bitten to interrupt any function. Whenever you have operating problems you can simply interrupt the function and start again. You can practice operating your set without any worries. No matter which buttons you press, you cannot damage it. User guide With 0SD {On Screen Display) the corresponding functions appear on the TV-screen.
Automatic Channel Allocation FOLLOW TV With this function the video recorder maintains the same programmer sequence as on the TV set. This only functions if the video recorder {socket [ EXT 1} and the TV stare connected via a scary cable. Additional equipment connected to socket must be switched off. @ Switch on the TV set. 9 Select programmer number 1" on the TV set . © Press the [AUTONOMOUS button on your video recorder.
2. PLAYBACK @ insert the cassette into the cassette slot. €) Press the playback button[ FLARE ], © Picture scanning: Press the 8 reverse) o [ {forward) button once or several times. You have a choice of several picture scanning speeds. @ Interrupt: Press the button. Gimlet and rewind: Interrupt the playback function and press the [ {rewind} or [P {wind) button. 1f you want to carry out this function on your video recorder, then turn the outer rotary control [ t0 the left or to the right.
Tape position/Index search Tape position: The elapsed playback time, given to the hour and minute, appears in the display. When you load a cassette, the video recorder must first calculate the playing time. Therefore, " appears first and only after the tape has been running for a few seconds the playing time will be shown. Tha playback time displayed can be incorrect when using camcorder cassettes or with cassettes made for NTSC-VHS equipment.
3. RECORDING € insert a cassette or switch the video recorder on with the [T button. © Use the or (2 Hutton or the buttons to select the programmer number from which you wish to record, 8.9. P 01", M.~ FH €) Press the [RECORD Y button. . ves ”: rr = Idyllic © To stop recording, press the Hutton. Long play function You can reduce the recording speed by half. This makes it possible to record, for example, 8 hours instead of 4 hours on an 'E240" cassette.
Programming with "SHOW VIEW’ €@ Make sure that a cassette without erase protection has g J been loaded. Switch to standby with the button, All the information required for a programming is contained A programmed recording will only function when the encoded in the SHOW VIEW code. video recorder is switched to standby with the STANDBY O | bastion. © Switch on the TV set.
A — Important programming notes + When recordings have been programmed, © appears in the display. « The programmed recording will always be made at the recording speed {SP/LP) that at the time has been selected on the video recorder. » You cannot aerate the video recorder manually while a programmed recording is being made. If you want to interrupt the programmed recording, pass the button.
4, SPECIAL FEATURES Tuner mode You can also use your video recorder as a TV receiver {tuner). @ Hold the button, until [3 appears in the display. © Choose the required programmer number with the or [P mutton or with the buttons. @ Switch the video retarder to standby by pressing the STANDBY Q) | button when you no longer want to watch television. Sound track selection You can select the required sound track during tuner-mode, stop or playback.
Setting the clock @ Press the bitten on the video recorder. €) Confirm the line 'CLOCK . 0 Adjust ‘TIME", 'YEAR", '"MONTH', ‘DATE’ if required. @) Confirm each entry. Channel number or frequency display You can switch between the display for ‘channel number” or "frequency’ for manual channel! search, €) Press the button. @) Select and confirm "CHANNEL/FREQUENCY” . € Select and confirm ‘CHANNEL' or ‘FREQUENCY’ .
VR 675 — — Nate: This modulate frequency might already be occupied by another TV station in your reception area. In this case you will find that the picture quality on your TV set will be poor when receiving one or mere TV channels. * Adjusting the modulator frequency: If the picture quality only deteriorates when the video recorder is switched on, adjust the modulator frequency. The frequency can be adjusted at step @With the [P~ lor the [2F] button. Confirm the adjusted frequency with the button.
