CONTENTS Section 1 INTRODUCTION Features 2 SUMMARY OF BUTTONS, CONTROLS AND SOCKETS Safety instructions 3 INSTALLATION Connecting the aerial Selecting the Display language Tuning your TV set to the video recorder 4 SETTING THE CLOCK ON THE VIDEO RECORDER 5 STORING TV STATIONS REMOTE CONTROL.
SUMMARY OF BUTTONS, CONTROLS AND SOCKETS Getting familiar with your video recorder The symbols below are listed in the same sequence as they appear on the voids recorder. Detailed information concerning their functions are explained in the relevant sections. i symbols only appear on the remote contra or dither from the symbols on the video recorder, they are placed between brackets in the ext.
Safety instructions and precautions The manufacturer cannot be held Hale for damages which are Incurred by not using the viced recorder in compliance with the guarantee conditions, safety instructions or precautions. # First check if your supply voltage is the same as that given on the type plate at the rear. # The video recorder should be allowed to acclimatize for at least two hours after unpacking before connecting it to the mains.
Tuning your TV to the video recorder signal (D switch on the TV. @ Cross A to remove the cassette, if already loaded, [6F ) @ Select on the TV the pres election (programmer) number for the video recorder. Most modern TV sets have pres election numbers to select TV stations or the video recorder signal, Refer to the Operating Instructions of your TV set to determine which pres election number to choose and how to tune it.
@ Cross SET CLOCK once more to complete setting the clock. For about 5 seconds the Display shows the date and the weekday, standby the Display shows the current time. if you disconnect the video recorder from the mains or after a mains allure, the clock will remain accurate for one month.
General notes: — Once you have stored all TV stations you can use the digit buttons (0-9) to select these TV stations. — If you store a TV station under a number that is already used, the new station will be stored, and the old TV station will be deleted. This van be useful if you find better reception of a TV station which has already been stored. REMOTE CONTROL With the remote control unit you can operate nearly all functions of the video recorder.
® Press change to tape length in the following sequence: E30, E60, ES0, E105, E120, E150, E180, E105, E210, E240, E300, EC, E30, ete. ® Cross SELECT TAPE again. Loading a cassette @ Hold the cassette with the title label facing you and the window side up. Push the cassette until it is caught and drawn inside automatically. inserting a cassette will switch on the video recorder automatically, Do not pull out the cassette, once automatic loading has started. @ i necessary, press W or 44th (rewind the tape.
PLAYING A CASSETTE @ switch on the TV. @ On the TV dissect the pres election number for the video recorder. @ Load a per-recorded cassette. ® press). On your TV you will now see the recording. The Display shows for example: TIME LEFT 328 17 \ RS BES] o5 00mz0a0ems ® Press M to interrupt playback. The Display shows for example: e roses B e LRI o (B & worm Note: if you wqu‘d like to start a recording from this point press @ € You will then get a clean continuation (automatic assembly).
& You can Interrupt the Intro scan function, pressing any tape transport bitten (e.g. ¥ if you have found the retarding you want to watch). Note: The Intro scan function cannot be used when a timed recording Is taking place or when no cassette Is loaded. Searching with picture: ® Pres sh, ® Freshness &, The tape will {re}wind at 7 times the normal speed with cloture but without sound. # Press ¥ again when the desired passage is reached.
An information fine appears at the top of the TV screen; f 7100 The following may be indicated in this information line: The number of the page on the screen. If ‘Stop changing pages’ is selected, & will be indicated, information, for example the name of the received TV station, the date and the time, Also page number “100" {generally the index} now appears on the screen. Note: The page number always consists of three digits {e.g. 120).
Using the Teletext system Your VCR is equipped to use the additional ‘FLOG information to improve user comfort, Al the features mentioned here are broadcaster defined. All described functions are defined by the broadcaster stations (Please contact your dealer 1o find out which teletext-broadeaster use FLO. Each displayed teletext {TXT) page shows on its bottom row up o 5 pieces of information, each indicating the subject of the page which s likely to be selected next.
If you don't want fo cancer the occupied TIMER-blocks: e Press The previously displayed TXT page will be shown again, the TXT programming mode is canceled, If you want to cancel en occupied TIMER-block and program it again: e Press + or digit button (0-8) to select the TIMER-block you want to cancel. & Press X on the remote control. e Cross The TV programmer page will be shown again on the TV screen, but now including a cursor, ® Press select the desired TV programmer. Cross (© &) again.
Programming a timed recording without Teletext (D Press & (D). The Display shows for example: All necessary data for recordings are stored in blocks. Each block contains a start time, & stop time, date and a practitioner number of a TV programmer. There are 8 programming blocks available, so you can program the video recorder to record 8 TV programmed successively. @ Cross the digit buttons {0-9} to select the book you want to program.
Press the digit buttons {0-8) to select the correct TV station to be recorded. vPS If 'VPS’ lights up on the Display, the VPS control has been switched on for this block. if a TV station does not transmit a VP code, the VPS control has no function. o Use (X} to switch off the VPS control for this block ('VPS' disappears). The video recorder then records In accordance with the times you have entered.
Programming on the remote control without Teletext Yau: can program timed recordings on the remote control using (@LCD) and (0-9) and then transmit the programming details to the video recorder using (TRANSMIT). ©On the Display of the remote control all the programming steps will be shown. Note: If during programming no bunion Is pressed within T minute, you have to start the programming sequence from the beginning again. @ Press to recall the last programmed recording details.
Canceling a block You can cancel a block of a recording already in progress: ® pressie) You can cancel a block of a recording which has not yet started: @ Press © @ If necessary, press defect the block to be canceled. @ Press X. One Touch Recording (OTR) Use OTR to record immediately for minutes, sto. @ Load a cassette. @ Press select the TV station you want to retard from, @ Press OTR {or simultaneously the two buttons {77 ¢R on the remote control. The recording stairs.
Special recording modes » Press RECORDING MODE {REC. MODE) one or more times. & To return to normal recording of both picture and sound from the TV programmer, press RECORDING MODE (REC. MODE) until the Display shows for a few seconds: THEM LEFT P Sirs ag: C Th UCLA 5 L conferrer @ assume Audio recording You can make WiFi stereo audio recordings with a play/record time hours on an E240 cassette. @ Load an unprotected cassette. It you have already loaded a cassettes, first press M.
Audio dubbing with audio mixing desk Copying via the aerial sockets 17 and @ You can mix the original WiFi sound with an external sound connecting your video recorder 1o an audio mixing desk.
WATCHING TV VIA THE VIDEO RECORDER (TUNER MODE) @ Switch ante TV, @ Ont he TV select the pres election number for the video recorder. @ Press & Press C/P one or twice to select presentation numbers (P) or channel numbers {C). & Select the TV stations using (V). The Display shows for example: EXTIRPATE BSD g5cmmmesvasan Charterer Note: Tha video recorder remains in the Tuner mode.
TROUBLE CHECKS 1 5 Disturbed or noisy picture a s the video recorder connected to the mains? b Has the 30-29 channel control been adjusted? TV station selected on the video recorder, but no picture is received a Haste pres election number for the video recorder been selected on the TV? b s this TV station broadcasting at the moment? ¢ Haste TV station been stored correctly? No picture or sound when using a 21-pin connector cable {Euro cable) a Has the External input been selected on the TV? b Has the Extern
TECHNICAL DATA* General Mains voltage Mains frequency Po war consumption Wind/rewind time Lambent temperature during operation Humidity Di mansions Wright Position for use Number of per-selections Numbers of programmable blocks Number of days in advance 220V 4810 typical (14 W typ. in standby) 830 sec. typical for E-180 +10°Cto +35°C 420 x 99 x 370 mm (inch. feet} 7.1 kg approx. max. 15° inclination on all sides 48 + ext.
