Contestable Safety Precautions WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. o The POWER button does not completely shut off mains power from the unit, but switches operating current on and off. #The rating plate and the safely caution are on the rear of the unit. Introduction Congratulations on purchasing your new VOR (Video Cassette Recorder). Iris one of the most sophisticated yet simple-to-use home video recorders you can buy.
— Description of Controls 3 Front Panel o —rel |, VCR Display Panel BELIEVE wny fmm Loy Cassette Compartment ‘Where the video cassette is inserted. 2 Wireless Remote Sensor Reeves the signal from the (wireless) remote control. 3 Burton Press to rewind tapes. Also, during playback, press this ‘button for reverse visual search. 4 PLAY Button « Press to pay back a tape. « Press to release the Slow or Search mode and return to playback. & FF (Fast Button Press to move the tape forward vapidity.
Description of Controls (contd) Rear Panel (Alternating Current) Power Cord Conn est the AC Power Cord to a household outlet, 22 AUDIO Input) jack For audio input connection from the output jack of 3 portable video camera, another VCR, or another audio soiree, 23 AUDIO Jack For connection to the audio input connector on a TV, another VCR, or an audit tape recorder. 24 VIDEO OUT{put) Jack For video output connection another VCR.
Remote Control Transmitter VCA Controls VCR POWER Bunion Press to tun VCR power ON or OFF, Also, used to set the VCR for unattended timer recording. & PAUSE/STILL Button « Press once to temporarily stop the tape during recording (Pause). + Press once to freeze the tape picture during playback {Sti. « Press again when you want to resume normal playback or recording. 7 EJECT BUTTON Press (o eject the cassette, 8 Frame) Advance) Bunion Press while in the Stile mode to advance the picture one. frame at a time.
Before Uncompromising 1 Load The Batteries as Follows: 1 Remove the Battery Compartment | 2 Install two batteries as indicated 3 Replace the lid. lid from the bosom of the remote snide the Battery Compartment. control. B Bot torn af Emote Control Battery Replacement Canton + Do not mix old and new batteries. (Also never mix talkative batteries with manganese batteries.) “This remote control and batteries are supplied accessories. Please check to make sure they are included.
Step 1: Disconnect the Antenna from Your TV. Back of TV {example only} %I = Outdoor = 3 Indoor Antenna Antenna S Step 22 Connect Your Antenna or Cable to Your VCR. Butte TV Back of VCR el > ffrmmt e e i ANT.N {In fom Antenna} [y Step 3: Connect Your VCR to Your TV. ANT.IN Back of VCR Back Coral Cable = antenna (supplied) Plug the AG {Alternating Current) cord into an AC outlet.
Getting Hooked Up (continued) VCR to AV TV Hook-U| }/ Video Cable . } J Video and Video and P Audio in Audio out Jacks Audio Cable, (Select AY on your T) Playing a Tape that the batteries are loaded in the remote control and the Power On: connections have been completed before continuing to the steps ™ Select video Below. ‘channel or Select AY mode “Turn the TV on. Select the video channel {or AV mode). sy Insert a cassete.® Cassette Tape ]— * The VCR (Video Cassette Recorder) Power will come on.
Set the Clock 9 To set your VCR 1o the present day and time, follow steps 1 -4 below. Once set, your YCR (Video Cassette Recorder) wail maintain the time in its internal clock, and will make timer recording possible. Make sure ~ your VCR and TV ace connected and tuned on. + to make each entry within 10 seconds, otherwise the VCR will exit the Clock Set mode and you will have to start over. STATUS s Cross the MENU button, Then press the 4 LI button fo select “CLOCK SET from the Bunion men serene. CLEAR .
Placing Local Channels in the VCR With the feature, you can program your YCR (Video Cassette Recorder) Lo receive the channels available in ‘your area. With Add/Delete feature you can add or delete any channel. You must issue your remote control, At the TV and the VCR Tue the TV on and select the video channel {or AV mode). Tum the VCR on.
scored on a cassette tape, follow steps 1 -7 below. Read all the instructions before starting, You must use your remote control. v Make sure .. the steps in “Hook Up Your VCR™ have been completed. Power ON: Select VCR channel, Ut VCR Indicator Tum he TV on. Tam to your VCR channel. STOP Bunion At the VCR Insert 2 cassette with the record tab in place. ‘The power will come on.
On-Screen Displays (OSD) (SRS PO SO remorse proprietor STUTTERER Aback EET THUNDERSTORMS Main Menu VCR Set Up Bunion Pressed Time P TR nae--Channel Mz Counter and Counter Memory VCH Status Display T ST USES, S 1. Nora L PGS CONTROL (08 Picture Control Simulcast 0SD Main Menu Serene Press the MENU button on the remote to display the main menu screen, ‘Then press the NUMBER button on the remote control for the desired feature displayed on the menu.
—One Touch Recording (OTR) 13 set the VCR to automatically shut off after recording is completed, follow steps 1-3 below. OTR Jets you quickly specify how long you want recording to continue. You don’t have to program the timer with this function. ‘You must use your remote control. Make sure + the steps in “Nesting Hooked Up” are done, channels are programmed into the VCR’s memory, and the TV and VCR are ‘both turned on. < the clock is set to the comet time. « the desired tape speed (SP, LF) is selected.
Timer Recording To record while you're away, follow steps 1-12 below. For each program you sef, the VCR will turn itself on, do the recording, and tuw off automatically. You can store up to eight programs, Instructions for each step appear on the TV screes after you begin. You must use your remote control. Make sure < the sips in “Getting Hooked Up” have been completed, an antenna or cable system is connected to FOR BACH STEP BELOW, YOU HAVE 60 SECONDS the VCR, and the VCR and TV are turned on.
R First, press two NUMBER buttons for the hour. S Next, press two NUMBER buttons for the 7 minute. Now, press NUMBER button “I” for AM or | oo “27 for PM. Aerator For example, for 9:30 PM, press NUMBER buttons 0-9, 3-0, 2. Rl First, press two NUMBER buttons for the hour. Next, press two NUMBER bunions for the i mint. For example, for 10:00 PM, press o PUSHER. b Select the Recording Speed ST Press the 1 or 2 button to choose SP or LP. BES.
Set Up G-Code Your VCR’s built-in G-Code allows you to program timer recordings in one easy step. When you give your VCR a programmer G-Code bummer (found in your TV Guide), it automatically records that program. Follow the steps below o set up G-Code. First, fill in the boxes on this pages. It will only take a few minutes, and you must do it if you want yous VCR’s G-Code work property.
&, &) S Press the MENU button. Then, press the canyon Number 2 button to select VCR SET UR. Srimcsctoe Seignior Toe e © (Test e o | F Press the Number 3 button to select obtuseness GUIDE CHANNEL SET. S o sk Collegiate Tommie T ERE ROE Look at the boxes you filled in on the SWEETENING, previous page. For stations whose guide | = channels and user channels are not the user 7 same, press [wo Number buttons for the PR guide channel and two Numbers bunions for the user channel.
Timer Recording with G-Cod Read steps 1 ~7 to program.a mire recording using G-CODE numbers. [make sure « Channels have been programmed. POWER + “The clock bas been set. Buffet + There is a tape in the VCR (make sure the tape’s record tab s intact and the tape is long enough to recons the program(s). + The VCR is in VCR position. + You have selected CABLE the TUNER SET UP men, You must do each step within 66 seconds of completing the previous step. If you don’t you will have to start again at step 1.
&, Press the Number [ or 2 buttons o select SP or LP. You cannot use the SPEED butter: on the remote control to choose the recording speed. G Press the MENU button. PROGRAM WAS COMPLETED / PLEASE TURN OFF VCR FOR TIMER RECORDING should appear on the screen (but if PROGRAM NOT COMPLETED appears, please begin again from step 1), After five seconds, the on-serene display will disappear and the TIMER Hg ht will appear on the display panel, I needed, press the G-CODE button and repeat steps 20 5.
Special Playback Features Is your VCR connected to your TV? Are you familiar with tape playback? If so, you are ready to enjoy the special playback features described on this page.You must use yon remote control. To Rapidly Locate a Particular Segment First, press the PLAY button. Next, press the or FF (Fast button. A rapid forward or reverse pioneer search begins. PAUSE/STILL Search speed is about @ times the normal speed.
_Special Playback Features (cont’d) 21 Auto Playback ‘When a tape is inserted, the power comes on, I the recons tab* i removed, playback begins. Auto Rewind ‘When a tape reaches its end during playback, fast forward, or manual scored, the VCR rewinds the tape and goes into Stop mode.
Re-Recording (Tape Duplication) Dubbing from any VHS recorder (of camcorder) to another i simple, Just use the connections and steps below. The example below uses two VCR like this one. Other VCR may operate differently. Insert a per-recorded tape. VCR 1 is the VCR that will play your sap. If the record tab is missing (page 6), playback stats. Tn that case, press the stop button. CONNECTIONS 1 Source Camcorder | player Insert a blank tape in the editing VCR.
Tape Counter Control Tape Operation 23 If ‘you always rewind your tapes fully and reset the tape counter, then you’ll be able to use a list of program locations as an index. You must use your remote control. D) researcher Button FF /SEARCH Button e STOP Burton — STATUS Button £ ©0T gvu {Counter) MEMORY Button Remote Control Go-To Function Select the Tape Counter Display To select the tape counter display, press the STATUS button. The tape counter display appears on the TV screen.
Notes on Q Operations Hook Up Your VCR « I the reception on all channels is unsatisfactory, you may inced to re-tune your TV set. Clock Adjustment « In the Clock Adjustment mode, be sure to eater the first digit and all subsequent entries within 10 seconds of one another. Otherwise, the VCR will automatically leave this mode and the program you were watching will retain to the screen. If this Happens, press the MENU button and start again, Be sure to enter “0” before single-digit members.
IMPORTANT NOTE: Periodic maintenance is squired in order fo maintain the unit’s continued excellent performance. Ratifier period of time the Video heads will require replacement, If cleaning or replacement of the Video heads is required, this service should be performed by an authorized Widen System Service Center. Check the following points once again if you are having some difficulty with your VCR (Video Cassette Recorder). ‘Timer recording can’t be performed...
Before Requesting Service (cont’d) r—Remote Control Correction VCR can't be remote controlled. « Aim the Remote Control directly at the remote sensor on the VCR. + Avoid all obstacles which may interfere with the signal pails. « Inspect or replace the batteries (P8). « Make sue batteries are inserted correctly (R6). —Miscellaneous Video cassette can’t be inserted... Video cassette can't be renovated.
