VR420CAT Video Cassette Recorder Hookup Pages
6 Hookups Without a Cable Box/Direct Broadcast System The basic VCR/TV connection – antenna/cable to VCR to TV – is shown below. If you have a Cable Box or a Direct Broadcast System, please see pages eight-nine. If you have a Stereo TV, please see page 10. After you hook up the VCR, go to page 11 to turn on the VCR. 1 Disconnect the antenna or cable from your TV.
Hookups Without a Cable Box/Direct Broadcast System (cont’d) 7 3 Connect the supplied black RF coaxial cable to the OUT Jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on type (supplied) or screw-on type of coaxial cable, whichever you prefer.) ANT IN AUDIO OUT IN VIDEO OUT CH3 CH4 ANT IN 75 ANT CAB / LE AUDIO OUT 75‰ ANT / CABLE IN VIDEO OUT ANTENNA IN Jack (on back of TV) example only CH3 CH4 RF coaxial cable 4 5 Plug in the TV and the VCR.
8 Hookups With a Cable Box/Direct Broadcast System There are two ways to connect your Cable Box/DBS to the VCR. With this connection: ● You may view any channel. ● You must select channels at the Cable Box/DBS. Channels cannot be changed at the VCR. ● You may not view a channel other than the one you are recording. ● You may not program channels at the VCR. ● You can only program a timer recording for one channel at a time.
Hookups With a Cable Box/Direct Broadcast System (cont’d) 9 With this connection: ● You may watch one channel while recording another. ● You may not record scrambled channels. 1 VCR ANT IN 2 Cable Box/DBS 75 ANT CAB / LE AUDIO IN OUT IN VIDEO OUT OUT CH3 CH4 RF coaxial cable Cable Signal RF coaxial cable 3 TV’s ANTENNA IN Jack Connections 1 2 Connect a Cable signal to the VCR’s ANT(enna) IN Jack.
10 Hookups with a Stereo TV 1 antenna or cable to ANT(enna) IN Jack ANT IN AUDIO OUT IN VIDEO VIDEO (yellow) and AUDIO (white) OUT Jacks OUT Audio and Video IN Jacks on TV CH3 CH4 2 Video Cable ● Audio and Video cables are not supplied. 1 Connect the antenna or cable to the ANT(enna) IN Jack on the back of the VCR. 2 Connect a video cable to the yellow VIDEO OUT Jack on the back of the VCR. Then, connect the other end of the video cable to the VIDEO IN Jack on your TV.
24 Front Panel STOP/EJECT Button Press once to stop the tape. When playback is stopped, press to eject the tape. Press to select an item in the menu. PAUSE Button While recording, press to pause the recording. Press again to resume recording. Details are on page 27. You can not pause a One-Touch Recording. During tape playback, press to freeze the picture. Press again to resume playback. Details are on page 38.
Rear Panel 25 ANT(enna) IN Jack Connect your antenna or cable here. Details are on pages six-10. AUDIO IN Jack Connect an audio cable coming from the AUDIO OUT Jack of a camcorder, another VCR, or an audio source here. Details are on page 34. AUDIO OUT Jack Connect an audio cable going to the AUDIO IN Jack of a camcorder, another VCR, or an audio system here. Details are on page 34.
34 Rerecording (Tape Duplication) 1. Audio cable from AUDIO OUT Jack of VCR 1 to AUDIO IN Jack of VCR 2 VCR 1 Playing VCR VCR 2 - Recording VCR ANT ANT IN AUDIO OUT IN VIDEO IN AUDIO OUT CH3 CH4 OUT IN VIDEO 2. Video cable from VIDEO OUT Jack of VCR 1 to VIDEO IN Jack of VCR 2 OUT CH3 CH4 3. RF coaxial cable from the OUT jack of VCR 2 to the TV’s ANTENNA IN Jack ● Audio and Video cables are not supplied. 1 2 3 Make the connections shown above. VCR 1 will play your tape.
