VR220CAT Video Cassette Recorder Owner’s Manual
Return your Warranty Registration card today to ensure you receive all the benefits you’re entitled to. Once your PHILIPS purchase is registered, you’re eligible to receive all the privileges of owning a PHILIPS product. So complete and return the Warranty Registration Card enclosed with your purchase at once. And take advantage of these important benefits.
Introduction 3 Welcome to your VCR owner’s manual. This manual has six sections: Setting Up Your VCR; Description of Controls; Basic Operations; Recording; Playing; and Information You May Need. The instructions explain all of the VCR’s features, which are listed below. You cannot hurt your VCR by trying the features! So read on – and relax.
Table of Contents Setting Up Your VCR Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Before Using Your VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Hookups Without a Cable Box/Direct Broadcast System . . . . . . . . . . . . . . . . . . . . .
Before Using Your VCR 5 Putting Batteries in the Remote Control 1 1 Remove the battery compartment lid on the bottom of the remote control by pressing the tab, then lifting the lid. 2 2 Place two AA batteries inside the battery compartment with their + and – ends aligned as indicated. 3 Replace the battery compartment lid.
Hookups Without a Cable Box / Direct Broadcast System The basic VCR/TV connection – antenna/cable to VCR to TV – is shown below. If you have a Cable Box or a Direct Broadcast System, please see pages eight-nine. If you have a Stereo TV, please see page 10. After you hook up the VCR, go to page 11 to turn on the VCR. 1 Disconnect the antenna or cable from your TV.
Hookups Without a Cable Box / Direct Broadcast System (cont’d) 7 3 Connect the RF coaxial cable (supplied) to the OUT Jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on type (supplied) or screw-on type of coaxial cable, whichever you prefer.
Hookups With a Cable Box / Direct Broadcast System There are two ways to connect your Cable Box/DBS to the VCR. With this connection: ● You may view any channel. ● You must select channels at the Cable Box/DBS. Channels cannot be changed at the VCR. ● You may not view a channel other than the one you are recording. ● You may not program channels at the VCR. ● You can only program a timer recording for one channel at a time.
Hookups With a Cable Box / Direct Broadcast System (cont’d) 9 With this connection: ● You may watch one channel while recording another. ● You may not record scrambled channels. 1 VCR ANT IN 2 Cable Box/DBS 75 ANT CAB / LE AUDIO IN OUT IN VIDEO OUT OUT CH3 CH4 RF coaxial cable Cable Signal RF coaxial cable 3 TV’s ANTENNA IN Jack Connections 1 2 Connect a Cable signal to the VCR’s ANT(enna) IN Jack.
Hookups With a Stereo TV 1 ANT antenna or cable to ANT(enna) IN Jack IN AUDIO OUT IN VIDEO VIDEO (yellow) and AUDIO (white) OUT Jacks OUT 2 3 Audio and Video IN Jacks on TV CH3 CH4 Video Cable Audio Cable ● Audio and Video cables are not supplied. 1 Connect the antenna or cable to the ANT(enna) IN Jack on the back of the VCR. 2 Connect a video cable to the yellow VIDEO OUT Jack on the back of the VCR. Then, connect the other end of the video cable to the VIDEO IN Jack on your TV.
Turning on Your VCR 11 Before turning on your VCR, make sure there are batteries in the remote control and the VCR and TV are connected correctly. ● You can not program channels if you are using a Cable Box or a Direct Broadcast System. 2 Turn on the TV. EJECT POWER 1 Press the VCR button, then press the POWER button. The VCR/TV light and the POWER light will appear on the VCR display panel. 4 MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 MEMORY 2 1 9 ALT.CH 0 Turn on the TV.
Automatic Channel Setup Although your VCR may automatically memorize the channels you receive when you turn it on for the first time, this function lets you set up the channels again. 2-3 1 Press the VCR button, then press the MENU button. EJECT POWER 1 SELECT op CHOOSE B → PROGRAM VCR SET UP TUNER SET UP SET CLOCK TO END PUSH EXIT MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 MEMORY 2 9 ALT.
Automatic Channel Setup (cont’d) 13 Adding/Deleting Channels 1 2 2-5 6 Press the VCR button, then press the MENU button. EJECT Press the PLAY/o button or the STOP/p button to select TUNER SET UP, then press the F.FWD/B button. 3 Press the PLAY/o button or the STOP/p button to select ADD/DELETE CH, then press the F.FWD/B button. SELECT op ADD/DELETE B 1 POWER MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 MEMORY 9 ALT.
Automatic Channel Setup (cont’d) Reviewing Memorized Channels 1 4 2-3 Press the VCR button, then press the MENU button. SELECT op CHOOSE B → PROGRAM VCR SET UP TUNER SET UP SET CLOCK TO END PUSH EXIT 2 Press the PLAY/o button or the STOP/p button to select TUNER SET UP, then press the F.FWD/B button. EJECT 1 POWER MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 MEMORY 0 REC /OTR PAUSE /STILL PLAY SELECT op CHOOSE B → AUTO PROGRAMMING ADD/DELETE CH CH MEMORY REVIEW REW F.FWD STOP CH.
Setting the Clock 15 Follow the steps below to set your VCR’s clock. Make sure: ● The VCR is on and the VCR/TV light appears on the display panel. (If it does not, press the VCR/TV button once.) ● You make each entry within 60 seconds of the previous entry. 1 2 Press the VCR button, then press the MENU button. Press the PLAY/o button or the STOP/p button to select SET CLOCK, then press the F.FWD/B button. 6 4-5 EJECT 1 POWER MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 MEMORY 3 9 ALT.
Daylight-Savings Time You may program the VCR so its clock will automatically move forward one hour in April and turn back one hour in October. Daylight-Savings Time is set to ON when you receive your VCR. Turn Daylight-Savings Time ON or OFF by following the steps below. Before you begin: ● Make sure the clock is set. Details are on page 15. 4 2-3 EJECT 1 Press the VCR button, then press the MENU button.
Language Selection 17 Follow the steps below to change the language of the on-screen displays and menus. 2-4 1 5 Press the VCR button, then press the MENU button. SELECT op CHOOSE B EJECT 1 → PROGRAM VCR SET UP TUNER SET UP SET CLOCK TO END PUSH EXIT 2 POWER MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 MEMORY 9 ALT.CH 0 Press the PLAY/o button or the STOP/p button to select VCR SET UP, then press the F.FWD/B button. REC /OTR PAUSE /STILL PLAY REW F.
Remote Control Buttons POWER Button Press to turn on or off the VCR or a Magnavox, Philips, or Philips Magnavox TV. (You must first press the VCR or TV button.) EJECT Button Press to eject the tape. MENU Button Press to access the VCR menu. Or, if you have a Magnavox, Philips, or Philips Magnavox TV, press the TV button, then press the MENU button to display the TV menu.
Remote Control Buttons (cont’d) 19 CLEAR Button Press to erase incorrect data when programming VCR functions. Also, press to reset the real-time counter. Details are on page 34. STATUS/EXIT Button Press to access or remove the VCR’s on-screen status display. Details are on page 20. Press to exit on-screen menus. Or, if you have a Magnavox, Philips, or Philips Magnavox TV, press the TV button, then press the STATUS/EXIT button, to see a TV status display or to remove the TV menu.
On-Screen Status Displays A status display will appear when you press the STATUS/EXIT button or certain function buttons. The contents of the status display will vary. To choose the status display mode, follow the steps below. If you select STATUS ON, then select COUNTER ONLY ON: ● Whenever you press the STOP/p button or the PLAY/o button, the status display will appear for five seconds. After five seconds, only the counter will remain on the screen. You must press the STATUS/EXIT button to remove it.
VCR Display Panel 21 VCR Display Panel Information about VCR operations is displayed here. Cassette Compartment Insert a tape here. STOP/EJECT PLAY REW F.FWD RECORD POWER POWER VIDEO PAUSE VCR/TV CST.IN TIMER RECORD CHANNEL MENU AUDIO STATUS/EXIT VCR/TV POWER POWER Light This light appears when the power is on. VCR/TV Light This light appears when the VCR is in VCR position. This light does not appear when the VCR is in TV position. Details are on pages 19 and 22. VCR/TV CST.
Front Panel F.FWD (Fast Forward) Button When playback is stopped, press to fast forward the tape at high speed. During tape playback, press to fast forward the tape while the picture stays on the screen. Details are on page 35. Press to select an item in the VCR menu. Remote Sensor Receives a signal from your remote control so you can operate your VCR from a distance. POWER Button Press to turn the VCR power on and off. PAUSE Button While recording, press to pause the recording.
Rear Panel 23 ANT(enna) IN Jack Connect your antenna or cable here. Details are on pages six-10. AUDIO IN Jack Connect an audio cable coming from the AUDIO OUT Jack of a camcorder, another VCR, or an audio source here. Details are on page 32. AUDIO OUT Jack Connect an audio cable going to the AUDIO IN Jack of a camcorder, another VCR, or an audio system here. Details are on page 32.
Playing 1 2 Read and follow the steps below to play a tape. 1 Turn on the TV and set it to channel 3 or 4, whichever channel the CH3/CH4 switch on the back of the VCR is set to. 2 Insert a tape in the VCR. The POWER, VCR/TV, and CST. IN lights will appear on the display panel. If the tape’s record tab has been removed, playback will start automatically. 6 3 If playback does not start automatically, press the VCR button, then press the PLAY/o button.
Recording 25 1 2 Read and follow the steps below to record a television program. 1 Turn on the TV and set it to channel 3 or 4, whichever channel the CH3/CH4 switch on the back of the VCR is set to. 2 3 Insert a tape with its record tab intact in the VCR. Turn on the TV. Insert a tape in the VCR. EJECT POWER 5 If the VCR/TV light appears on the display panel, go to step 4. If the VCR/TV light does not appear, press the VCR button, then press the VCR/TV button once.
Recording One Channel/Watching Another 1 2 3&7 Press the VCR button. EJECT POWER Press the REC(ord)/OTR button to start a recording of the current channel. (Details are on page 25.) The RECORD light will appear on the VCR display panel. 3 Press the VCR/TV button to put the VCR in TV position. The VCR/TV light will disappear from the VCR’s display panel. 4 Use the TV remote control to select the channel you want to watch at the TV.
One-Touch Recording 27 The One-Touch Recording (OTR) feature allows you to set an immediate timed recording 30 minutes to eight hours long. Before you begin: ● Set up the channels at the VCR. ● Select a recording speed (SP, SLP) with the SPEED button. ● Put a tape in the VCR. Make sure the tape’s record tab is intact and the tape is long enough to record the program(s). If the end of a tape is reached during an OTR, the VCR will eject the tape and turn itself off. ● Place the VCR in VCR position.
Timer Recording Follow the steps below to program your VCR to record TV programs while you’re away from home. The VCR will turn itself on, record, and turn itself off automatically. Before you begin: ● Set up the channels at the VCR. Details are on page 12. ● Set the clock. Details are on page 15. ● Put a tape in the VCR. Make sure the tape’s record tab is intact and the tape is long enough to record the program(s). ● Put the VCR in VCR position. The VCR/TV light will appear on the display panel.
Timer Recording (cont’d) 29 4 Use the Number buttons (1 - 8) to select a slot in which to store the timer recording. There are eight slots. Numbers for open slots will flash on the screen. NOTE: If you enter a number for a slot that has already been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on the screen briefly. Information about the program in that slot will appear on the screen. If this happens, press the STATUS/EXIT button, then select another number.
Timer Recording (cont’d) 8 10 Press the Number 1 button to record in SP speed or the Number 2 button to record in SLP speed. (See the chart below.) You cannot use the SPEED button at this time. ONE TIME PROGRAM PROGRAM 1 CHANNEL 10 TIME ON 09:30 PM TIME OFF 11:00 PM REC SPEED SLP SP=1 SLP=2 EJECT POWER 8 9 TO CORRECT PUSH CLEAR TO END PUSH EXIT 9 MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 11 9 MEMORY ALT.
Timer Recording (cont’d) 31 5 2-4 Checking or Cancelling Timer Recordings 1 With the VCR on and in VCR position (the VCR/TV light will appear on the display panel), press the VCR button, then press the MENU button. 2 Press the PLAY/o button or the STOP/p button to select PROGRAM, then press the F.FWD/B button. 3 Press the PLAY/o button or the STOP/p button to select PROGRAM REVIEW, then press the F.FWD/B button.
Rerecording (Tape Duplication) 1. Audio cable from AUDIO OUT Jack of VCR 1 to AUDIO IN Jack of VCR 2 VCR 1 Playing VCR VCR 2 - Recording VCR ANT ANT IN AUDIO OUT IN VIDEO IN AUDIO OUT CH3 CH4 OUT IN VIDEO 2. Video cable from VIDEO OUT Jack of VCR 1 to VIDEO IN Jack of VCR 2 OUT CH3 CH4 3. RF coaxial cable from the OUT jack of VCR 2 to the TV’s ANTENNA IN Jack ● Audio and Video cables are not supplied. 1 2 3 Make the connections shown above. VCR 1 will play your tape.
Repeat Play 33 Follow the steps below to make the VCR play a tape over and over. 5 1 2-4 Press the VCR button, then press the MENU button. EJECT SELECT op CHOOSE B 1 → PROGRAM VCR SET UP TUNER SET UP SET CLOCK TO END PUSH EXIT 2 POWER MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 MEMORY 9 ALT.CH 0 Press the PLAY/o button or the STOP/p button to select VCR SET UP, then press the F.FWD/B button. REC /OTR PAUSE /STILL PLAY REW F.
Real-Time Counter Memory Follow the steps below to reset the real-time counter to zero at a tape location you want to refer to later. 3 1 2 Press the VCR button. EJECT POWER Play, fast forward, or rewind a tape to the location that you would like to refer to later. Press the STOP/p button to stop the tape. 3 Press the STATUS/EXIT button to see the status display. STOP SLP 1:08PM CH10 5 2 1 : 23 : 45 MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 MEMORY 4 9 ALT.
Special Effects Playback 35 Forward and Reverse Searching (SP/LP/SLP) 1 During tape playback, press and release the F.FWD/B button or the REW(ind)/{ button. A fast forward or reverse picture search will begin. EJECT POWER 2 To return to playback, press the PLAY/o button. Super High Speed Searching (LP/SLP) MENU STATUS/EXIT CLEAR 1 2 3 4 5 6 7 8 MEMORY 9 ALT.CH 0 1 REC /OTR PAUSE /STILL PLAY During tape playback, press the F.FWD/B button or the REW(ind)/{ button, then press again.
Automatic Operation Features The following playback features will always operate. Automatic Playback When you put a tape in the VCR, the power will come on automatically. If the tape’s record tab is missing, playback will begin. If a timer recording is set, the power will not come on automatically when you insert a tape with the record tab intact. If a timer recording is set and the VCR power is off, the VCR will eject the tape if the record tab is missing.
Blue Background 37 If you want the TV screen to be solid blue when a weak signal is received, set BLUE BACKGROUND to ON. The screen will be blue and the sound will be muted. Or, if you want to receive the weak signal, set BLUE BACKGROUND to OFF. When you select a channel that is receiving a weak signal, you will see and hear the static in the TV programming. The channel number will not appear on the screen when you select a weak channel. To set BLUE BACKGROUND to ON or OFF, follow these steps.
Helpful Hints If you are having problems with your product, check this list of problems and possible solutions before requesting service. You may be able to solve the problem yourself. If you need to call a customer service representative, please know the model number and serial number of your product before you call. This information is displayed on the back of the product. Also, please take a moment to identify the problem you are having, and be prepared to explain this to the representative.
Helpful Hints (cont’d) 39 TV programs cannot be watched normally. • Put the VCR in TV position, then change channels at the TV. (Press the VCR/TV button so that the VCR/TV light disappears from the display panel. Details are on page 22.) • Check the connections between the VCR, TV, antenna/cable, and Cable Box/Direct Broadcast System (if applicable). Details are on pages six-10. Tape cannot be inserted. • Insert the tape, window side up, with the record tab facing you.
RENEWED 90 DAY LIMITED WARRANTY
Glossary/Specifications Glossary AUDIO IN/OUT Jacks: jacks located on the front and back of the VCR which are used to record audio from another source (IN) or to send audio to another system (OUT). Automatic Channel Setup: process in which the VCR memorizes all available channels. Then, when you press the CH(annel) o/p buttons, you only scan through channels you receive. Bands: settings that allow you to tune channels.
Index 42 ac power cord.................................23 accessories .......................................43 alt.ch button.....................................19 ant(enna) in jack ...................6-10, 23 audio in/out jacks10, 22, 23, 32, 41 automatic playback .......................................36 rewind, eject, off........................36 batteries ..............................................5 blue background..............................37 cassette compartment...................
SUPPLIED ACCESSORIES The following items are supplied with your VCR; they are provided to help you use or set up your VCR. Remote Control 4835 218 37313 Two AA Batteries 4835 138 17012 RF Coaxial Cable, 75 ohm 4835 323 27011 OPTIONAL ACCESSORIES The following additional items are not provided with your VCR, but they are designed for use with your new VCR. To order these optional accessories, contact us at: Philips Parts & Accessories Marketing Department 401 East Old Andrew Johnson Highway P.O.
