Over-ear TAPH802 User manual Register your product and get support at www.philips.
Contents 1 Important safety instructions 2 Hearing Safety General information 2 2 2 Your Bluetooth on-ear headset 3 What's in the box Other devices Overview of your Bluetooth on-ear headset 3 3 3 Get started Charge your headset Pair the headset with your mobile phone 4 Use your headset Connect the headset to a Bluetooth device Manage your calls and music Connect to ANC (active noise cancelation) Wear your headphones 3 4 4 4 5 5 5 6 6 5 Technical data 7 6 Notice 8 Notice of compliance 8 Dec
1 Important safety instructions Hearing Safety Danger To avoid hearing damage, limit the time you use headset at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guidelines when using your headset. • Listen at reasonable volumes for reasonable periods of time. • Be careful not to adjust the volume continuously upwards as your hearing adapts.
2 Your Bluetooth on-ear headset Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. With this Philips wireless on-ear headset, you can: • enjoy convenient wireless handsfree calls; • enjoy and control wireless music; • switch between calls and music. • enjoy noise cancelation. Other devices A mobile phone or device (e.g.
3 Get started Make sure that the headset are fully charged. Press and hold the button for 2 seconds to turn the headset on. Charge your headset Note Before you use your headset for the first time, charge the battery for one and a half hour for optimum battery capacity and lifetime. Use only the original USB charging cable to avoid any damage. Finish your call before charging the headset, as connecting the headset for charging will power the headset off.
4 Use your headset Connect the headset to a Bluetooth device Turn on your mobile phone/Bluetooth device. Press and hold the button for 2 seconds to turn the headphones on. The white LED flashes. Then the blue LED flahses, voice of "Device connected" is triggered. The headset are reconnected to the last connected mobile phone/ Bluetooth device automatically. If the last one is not available, the headset try to reconnect to the second last connected device.
Other headset indicator status Headset status Indicator The headset are connected to a Bluetooth device, while the headset in standby mode or while you are listening to music. The blue LED flashes for every 8 seconds. The headset are ready for pairing. The LED flashes blue and white alternately. The headset are on but not connected to a Bluetooth device. The blue LED flashes quickly If no connection can be made, the headset will turn itself off within 5 minutes. Low battery level.
5 Technical data Music time (ANC enabled with Bluetooth): 15 hours Talk time (ANC enabled with Bluetooth): 15 hours Standby time (ANC enabled with Bluetooth): 15 hours Normal time for a full charge: 2 hours Rechargeable lithium polymer battery (530 mAh) Bluetooth 4.2, Bluetooth mono support (Headset Profile - HSP, Hands-Free Profile - HFP), Bluetooth stereo supported (Advanced Audio Distribution Profile - A2DP; Audio Video Remote Control Profile-AVRCP) Frequency range: 2.402-2.
6 Notice Notice of compliance Notice for US The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. FCC rules This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Do not incinerate. Batteries may explode if overheated. For disposal or recycling information, please contact your local authorities or visit www.recycle.philips.com. If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headset. Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.
7 Frequently asked questions My Bluetooth headset do not switch on. The battery level is low. Charge the headset. I cannot pair my Bluetooth headset with a mobile phone. The Bluetooth is disabled. Enable the Bluetooth feature on your mobile phone and turn on the mobile phone after you turn on the headset. Pairing does not work. Make sure the headset are in pairing mode. • Follow the steps described in this user manual. The mobile phone cannot find the headset.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product. UM_TAPH802_10_EN_v0.
